Screen NISSAN TIIDA 2007 Service Manual PDF

CVT-70
DTC U1000 CAN COMMUNICATION LINE
Revision: June 20062007 Versa
TCM terminal data are reference values, measured between each terminal and ground.
Diagnostic ProcedureUCS005YP
1. CHECK CAN COMMUNICATION CIRCUIT
With CONSULT-II
1. Turn ignition switch ON and start engine.
2. Select “SELF-DIAG RESULTS” mode for “TRANSMISSION”
with CONSULT-II.
Is any malfunction of the
“U1000 CAN COMM CIRCUIT” indicated?
YES >> Print out CONSULT-II screen, go to LAN section. Refer
to LAN-47, "
CAN System Specification Chart" .
NO >>INSPECTION END
TerminalWire
colorItem Condition Data (Approx.)
5 L CAN-H — —
6 P CAN-L — —
SCIA5982E

DTC P1701 TRANSMISSION CONTROL MODULE (POWER SUPPLY)
CVT-145
D
E
F
G
H
I
J
K
L
MA
B
CVT
Revision: June 20062007 Versa
DTC P1701 TRANSMISSION CONTROL MODULE (POWER SUPPLY)PFP:31036
DescriptionUCS0062D
When the power supply to the TCM is cut OFF, for example because the battery is removed, and the self-diag-
nosis memory function stops, malfunction is detected.
NOTE:
Since “P1701 TCM-POWER SUPPLY” will be indicated when replacing TCM, perform diagnosis after
erasing “SELF-DIAG RESULTS”
On Board Diagnosis LogicUCS0062E

This is not an OBD-II self-diagnostic item.

Diagnostic trouble code “P1701 TCM-POWER SUPPLY” with CONSULT-II is detected when TCM does
not receive the voltage signal from the battery power supply.

This is not a malfunction message. (Whenever shutting OFF a power supply to the TCM, this message
appears on the screen.)
Possible CauseUCS0062F
Harness or connectors
(Battery or ignition switch and TCM circuit is open or shorted.)
DTC Confirmation ProcedureUCS0062G
NOTE:
If “DTC Confirmation Procedure” has been previously conducted, always turn ignition switch OFF and
wait at least 10 seconds before conducting the next test.
After the repair, perform the following procedure to confirm the malfunction is eliminated.
WITH CONSULT-II
1. Turn ignition switch ON. (Do not start engine.)
2. Select “DATA MONITOR” mode for “TRANSMISSION” with
CONSULT-II.
3. Wait for at least 2 consecutive seconds.
4. If DTC is detected, go to CVT-147, "
Diagnostic Procedure" .
BCIA0031E

SHIFT POSITION INDICATOR CIRCUIT
CVT-175
D
E
F
G
H
I
J
K
L
MA
B
CVT
Revision: June 20062007 Versa
SHIFT POSITION INDICATOR CIRCUITPFP:24810
DescriptionUCS006XJ
TCM sends the switch signals to combination meter via CAN communication line. Then selector lever position
is indicated on the shift position indicator.
CONSULT-II Reference ValueUCS00642
Diagnostic ProcedureUCS00643
1. CHECK INPUT SIGNALS
With CONSULT-II
1. Start engine.
2. Select “MAIN SIGNALS” in “DATA MONITOR” mode for “TRANSMISSION” with CONSULT-II and read
out the value of “RANGE”.
3. Check that the following three positions or indicators are same.
–Actual position of the selector lever
–“RANGE” on CONSULT-II screen
–Shift position indicator in the combination meter
OK or NG
OK >>INSPECTION END
NG >> Check the following.
SHIFT POSITION INDICATOR SYMPTOM CHART
Item name Condition Display value
RANGESelector lever in “N” or “P” position. N·P
Selector lever in “R” position. R
Selector lever in “D” position. D
Selector lever in “L” position. L
Items Presumed location of trouble
Actual position does not change.Park/neutral position switch

Refer to CVT-78, "DTC P0705 PARK/NEUTRAL POSITION
SWITCH" .
CVT main system (Fail-safe function actuated)

Refer to CVT-60, "SELF-DIAGNOSTIC RESULT MODE" .
Shift position indicator in the combination meter does not indicate
any position.
Perform the self-diagnosis for CVT and the combination meter.

Refer to CVT-60, "SELF-DIAGNOSTIC RESULT MODE" and
DI-5, "
COMBINATION METERS" . Actual position changes, but the shift position indicator in the
combination meter does not change.
Actual position differs from the shift position indicator in the com-
bination meter.
Shift position indicator in the combination meter does not indicate
specific position only.Check the combination meter.

Refer to DI-5, "COMBINATION METERS" .

DI-22
COMBINATION METERS
Revision: June 20062007 Versa
Fuel Gauge Fluctuates, Indicates Wrong Value, or VariesEKS00I0K
1. CHECK FUEL GAUGE FLUCTUATION
Test drive vehicle to see if gauge fluctuates only during driving or at the instant of stopping.
Does the indication value vary only during driving or at the at the instant of stopping?
YES >> The pointer fluctuation may be caused by fuel level change in the fuel tank. Condition is normal.
NO >> Ask the customer about the situation when the symptom occurs in detail, and perform the trouble
diagnosis.
Fuel Gauge Does Not Move to Full positionEKS00I0L
1. OBSERVE FUEL GAUGE
Does it take a long time for the pointer to move to FULL position?
YES or NO
YES >> GO TO 2.
NO >> GO TO 3.
2. IDENTIFY FUELING CONDITION
Was the vehicle fueled with the ignition switch ON?
YES or NO
YES >> Be sure to fuel the vehicle with the ignition switch OFF. Otherwise, it will take a long time to move
to FULL position because of the characteristic of the fuel gauge.
NO >> GO TO 3.
3. OBSERVE VEHICLE POSITION
Is the vehicle parked on an incline?
YES or NO
YES >> Check the fuel level indication with vehicle on a level surface.
NO >> GO TO 4.
4. OBSERVE FUEL GAUGE POINTER
During driving, does the fuel gauge pointer move gradually toward EMPTY position?
YES or NO
YES >> Check the components. Refer to DI-23, "FUEL LEVEL SENSOR UNIT CHECK" .
NO >> The float arm may interfere or bind with any of the components in the fuel tank.
DTC [U1000] CAN Communication CircuitEKS00IAR
Symptom: Display CAN COMM CIRC [U1000] at the result of self-diagnosis for combination meter.
1. CHECK CAN COMMUNICATION
1. Select "SELF-DIAG RESULTS" mode for "METER" with CONSULT-II.
2. Print out CONSULT-II screen.
>> Go to "CAN SYSTEM". Refer to LAN-44, "
TROUBLE DIAGNOSIS" .

EC-8Revision: June 2006
INDEX FOR DTC
2007 Versa
INDEX FOR DTCPFP:00024
DTC No. IndexUBS00QB1
NOTE:

If DTC U1000 or U1001 is displayed with other DTC, first perform the trouble diagnosis for DTC
U1000, U1001. Refer to EC-151, "
DTC U1000, U1001 CAN COMMUNICATION LINE" .

If DTC U1010 is displayed with other DTC, first perform the trouble diagnosis for DTC U1010.
Refer to EC-154, "
DTC U1010 CAN COMMUNICATION" .
DTC*1
Items
(CONSULT-II screen terms)Reference page
CONSULT-II
GST*
2ECM*3
U1000
1000*4CAN COMM CIRCUITEC-151
U1001
1001*4CAN COMM CIRCUITEC-151
U1010 1010 CONTROL UNIT(CAN)EC-154
P0000 0000NO DTC IS DETECTED.
FURTHER TESTING
MAY BE REQUIRED.—
P0011 0011 INT/V TIM CONT-B1EC-156
P0031 0031 A/F SEN1 HTR (B1)EC-161
P0032 0032 A/F SEN1 HTR (B1)EC-161
P0037 0037 HO2S2 HTR (B1)EC-166
P0038 0038 HO2S2 HTR (B1)EC-166
P0075 0075 INT/V TIM V/CIR-B1EC-173
P0101 0101 MAF SEN/CIRCUITEC-178
P0102 0102 MAF SEN/CIRCUITEC-187
P0103 0103 MAF SEN/CIRCUITEC-187
P0112 0112 IAT SEN/CIRCUITEC-195
P0113 0113 IAT SEN/CIRCUITEC-195
P 0 11 7 0 11 7 E C T S E N / C I R CEC-200
P 0 11 8 0 11 8 E C T S E N / C I R CEC-200
P0122 0122 TP SEN 2/CIRCEC-206
P0123 0123 TP SEN 2/CIRCEC-206
P0125 0125 ECT SENSOREC-212
P0127 0127 IAT SENSOREC-215
P0128 0128 THERMSTAT FNCTNEC-218
P0130 0130 A/F SENSOR1 (B1)EC-220
P0131 0131 A/F SENSOR1 (B1)EC-227
P0132 0132 A/F SENSOR1 (B1)EC-233
P0133 0133 A/F SENSOR1 (B1)EC-239
P0137 0137 HO2S2 (B1)EC-248
P0138 0138 HO2S2 (B1)EC-257
P0139 0139 HO2S2 (B1)EC-267
P0171 0171 FUEL SYS-LEAN-B1EC-276
P0172 0172 FUEL SYS-RICH-B1EC-284
P0181 0181 FTT SENSOREC-291
P0182 0182 FTT SEN/CIRCUITEC-297
P0183 0183 FTT SEN/CIRCUITEC-297

INDEX FOR DTC
EC-9
C
D
E
F
G
H
I
J
K
L
MA
EC
Revision: June 20062007 VersaP0222 0222 TP SEN 1/CIRCEC-302
P0223 0223 TP SEN 1/CIRCEC-302
P0300 0300 MULTI CYL MISFIREEC-308
P0301 0301 CYL 1 MISFIREEC-308
P0302 0302 CYL 2 MISFIREEC-308
P0303 0303 CYL 3 MISFIREEC-308
P0304 0304 CYL 4 MISFIREEC-308
P0327 0327 KNOCK SEN/CIRC-B1EC-315
P0328 0328 KNOCK SEN/CIRC-B1EC-315
P0335 0335 CKP SEN/CIRCUITEC-319
P0340 0340 CMP SEN/CIRC-B1EC-327
P0420 0420 TW CATALYST SYS-B1EC-334
P0441 0441 EVAP PURG FLOW/MONEC-340
P0442 0442 EVAP SMALL LEAKEC-346
P0443 0443 PURG VOLUME CONT/VEC-354
P0444 0444 PURG VOLUME CONT/VEC-362
P0445 0445 PURG VOLUME CONT/VEC-362
P0447 0447 VENT CONTROL VALVEEC-369
P0448 0448 VENT CONTROL VALVEEC-376
P0451 0451 EVAP SYS PRES SENEC-382
P0452 0452 EVAP SYS PRES SENEC-385
P0453 0453 EVAP SYS PRES SENEC-391
P0455 0455 EVAP GROSS LEAKEC-398
P0456 0456 EVAP VERY SML LEAKEC-406
P0460 0460 FUEL LEV SEN SLOSHEC-415
P0461 0461 FUEL LEVEL SENSOREC-417
P0462 0462 FUEL LEVL SEN/CIRCEC-419
P0463 0463 FUEL LEVL SEN/CIRCEC-419
P0500 0500
VEH SPEED SEN/CIRC*5EC-421
P0506 0506 ISC SYSTEMEC-423
P0507 0507 ISC SYSTEMEC-425
P0605 0605 ECMEC-427
P0643 0643 SENSOR POWER/CIRCEC-430
P0705 0705 PNP SW/CIRCAT- 9 7 (A/T),
CVT-78
(CVT)
P0710 0710 ATF TEMP SEN/CIRCAT- 1 0 2
(A/T),
CVT-85
(CVT)
P0715 0715 INPUT SPD SEN/CIRCCVT-90
P0720 0720
VEH SPD SEN/CIR AT*5AT- 1 0 7 (A/T),
CVT-95
(CVT)
P0725 0725 ENGINE SPEED SIGAT- 11 3
P0731 0731 A/T 1ST GR FNCTNAT- 11 7
P0732 0732 A/T 2ND GR FNCTNAT- 1 2 1
DTC*1
Items
(CONSULT-II screen terms)Reference page
CONSULT-II
GST*
2ECM*3

EC-10Revision: June 2006
INDEX FOR DTC
2007 Versa
P0733 0733 A/T 3RD GR FNCTNAT- 1 2 4
P0734 0734 A/T 4TH GR FNCTNAT- 1 2 8
P0740 0740 TCC SOLENOID/CIRCAT- 1 3 4
P0744 0744 A/T TCC S/V FNCTNAT- 1 3 9 (A/T),
CVT-110
(CVT)
P0745 0745 L/PRESS SOL/CIRCAT- 1 4 5
P0746 0746 PRS CNT SOL/A FCTNCVT-118
P0750 0750 SFT SOL A/CIRCAT- 1 5 1
P0755 0755 SFT SOL B/CIRCAT- 1 5 6
P0776 0776 PRS CNT SOL/B FCTNCVT-121
P0778 0778 PRS CNT SOL/B CIRCCVT-124
P0840 0840 TR PRS SENS/A CIRCCVT-129
P0845 0845 TR PRS SENS/B CIRCCVT-137
P0850 0850 P-N POS SW/CIRCUITEC-436
P1148 1148 CLOSED LOOP-B1EC-442
P1217 1217 ENG OVER TEMPEC-443
P1225 1225 CTP LEARNINGEC-460
P1226 1226 CTP LEARNINGEC-462
P1421 1421 COLD START CONTROLEC-464
P1564 1564 ASCD SWEC-466
P1572 1572 ASCD BRAKE SWEC-473
P1574 1574 ASCD VHL SPD SENEC-483
P1610 - P1615 1610 - 1615 NATS MALFUNCTIONBL-212
P1705 1705 TP SEN/CIRC CVTCVT-150
P1715 1715 IN PULY SPEEDEC-485 (A/T),
EC-486
(CVT)
P1740 1740 LU-SLCT SOL/CIRCCVT-158
P1760 1760 O/R CLTCH SOL/CIRCAT- 1 6 1
P1777 1777 STEP MOTR CIRCCVT-164
P1778 1778 STEP MOTR FNCCVT-168
P1805 1805 BRAKE SW/CIRCUITEC-488
P2100 2100 ETC MOT PWREC-493
P2101 2101 ETC FUNCTION/CIRCEC-499
P2103 2103 ETC MOT PWREC-493
P 2 11 8 2 11 8 E T C M O TEC-506
P 2 11 9 2 11 9 E T C A C T REC-511
P2122 2122 APP SEN 1/CIRCEC-513
P2123 2123 APP SEN 1/CIRCEC-513
P2127 2127 APP SEN 2/CIRCEC-519
P2128 2128 APP SEN 2/CIRCEC-519
P2135 2135 TP SENSOREC-526
P2138 2138 APP SENSOREC-532
P2A00 2A00 A/F SENSOR1 (B1)EC-540
DTC*1
Items
(CONSULT-II screen terms)Reference page
CONSULT-II
GST*
2ECM*3

EC-12Revision: June 2006
INDEX FOR DTC
2007 Versa
Alphabetical IndexUBS00QB2
NOTE:

If DTC U1000 or U1001 is displayed with other DTC, first perform the trouble diagnosis for DTC
U1000, U1001. Refer to EC-151, "
DTC U1000, U1001 CAN COMMUNICATION LINE" .

If DTC U1010 is displayed with other DTC, first perform the trouble diagnosis for DTC U1010.
Refer to EC-154, "
DTC U1010 CAN COMMUNICATION" .
Items
(CONSULT-II screen terms)DTC*1
Reference page
CONSULT-II
GST*
2ECM*3
A/F SENSOR1 (B1) P0130 0130EC-220
A/F SENSOR1 (B1) P0131 0131EC-227
A/F SENSOR1 (B1) P0132 0132EC-233
A/F SENSOR1 (B1) P0133 0133EC-239
A/F SENSOR1 (B1) P2A00 2A00EC-540
A/F SEN1 HTR (B1) P0031 0031EC-161
A/F SEN1 HTR (B1) P0032 0032EC-161
A/T 1ST GR FNCTN P0731 0731AT- 11 7
A/T 2ND GR FNCTN P0732 0732AT-121
A/T 3RD GR FNCTN P0733 0733AT-124
A/T 4TH GR FNCTN P0734 0734AT-128
A/T TCC S/V FNCTN P0744 0744AT-139 (A/T),
CVT-110
(CVT)
APP SEN 1/CIRC P2122 2122EC-513
APP SEN 1/CIRC P2123 2123EC-513
APP SEN 2/CIRC P2127 2127EC-519
APP SEN 2/CIRC P2128 2128EC-519
APP SENSOR P2138 2138EC-532
ASCD BRAKE SW P1572 1572EC-473
ASCD SW P1564 1564EC-466
ASCD VHL SPD SEN P1574 1574EC-483
ATF TEMP SEN/CIRC P0710 0710AT-102 (A/T),
CVT-85
(CVT)
BRAKE SW/CIRCUIT P1805 1805EC-488
CAN COMM CIRCUIT U1000
1000*4EC-151
CAN COMM CIRCUIT U1001
1001*4EC-151
CKP SEN/CIRCUIT P0335 0335EC-319
CLOSED LOOP-B1 P1148 1148EC-442
CMP SEN/CIRC-B1 P0340 0340EC-327
COLD START CONTROL P1421 1421EC-464
CONTROL UNIT(CAN) U1010 1010EC-154
CTP LEARNING P1225 1225EC-460
CTP LEARNING P1226 1226EC-462
CYL 1 MISFIRE P0301 0301EC-308
CYL 2 MISFIRE P0302 0302EC-308
CYL 3 MISFIRE P0303 0303EC-308
CYL 4 MISFIRE P0304 0304EC-308

INDEX FOR DTC
EC-13
C
D
E
F
G
H
I
J
K
L
MA
EC
Revision: June 20062007 VersaECM P0605 0605EC-427
ECT SEN/CIRC P0117 0117EC-200
ECT SEN/CIRC P0118 0118EC-200
ECT SENSOR P0125 0125 EC-212
ENG OVER TEMP P1217 1217EC-443
ENGINE SPEED SIG P0725 0725AT - 11 3
ETC ACTR P2119 2119EC-511
ETC FUNCTION/CIRC P2101 2101EC-499
ETC MOT P2118 2118EC-506
ETC MOT PWR P2100 2100EC-493
ETC MOT PWR P2103 2103EC-493
EVAP GROSS LEAK P0455 0455EC-398
EVAP PURG FLOW/MON P0441 0441EC-340
EVAP SMALL LEAK P0442 0442EC-346
EVAP SYS PRES SEN P0451 0451EC-382
EVAP SYS PRES SEN P0452 0452EC-385
EVAP SYS PRES SEN P0453 0453EC-391
EVAP VERY SML LEAK P0456 0456EC-406
FTT SEN/CIRCUIT P0182 0182EC-297
FTT SEN/CIRCUIT P0183 0183EC-297
FTT SENSOR P0181 0181EC-291
FUEL LEV SEN SLOSH P0460 0460EC-415
FUEL LEVEL SENSOR P0461 0461EC-417
FUEL LEVL SEN/CIRC P0462 0462EC-419
FUEL LEVL SEN/CIRC P0463 0463EC-419
FUEL SYS-LEAN-B1 P0171 0171EC-276
FUEL SYS-RICH-B1 P0172 0172EC-284
HO2S2 (B1) P0137 0137EC-248
HO2S2 (B1) P0138 0138EC-257
HO2S2 (B1) P0139 0139EC-267
HO2S2 HTR (B1) P0037 0037EC-166
HO2S2 HTR (B1) P0038 0038EC-166
IAT SEN/CIRCUIT P0112 0112EC-195
IAT SEN/CIRCUIT P0113 0113EC-195
IAT SENSOR P0127 0127EC-215
INPUT SPD SEN/CIRC P0715 0715EC-486
IN PULY SPEED P1715 1715EC-485 (A/T),
EC-486
(CVT)
INT/V TIM CONT-B1 P0011 0011EC-156
INT/V TIM V/CIR-B1 P0075 0075EC-173
ISC SYSTEM P0506 0506EC-423
ISC SYSTEM P0507 0507EC-425
KNOCK SEN/CIRC-B1 P0327 0327EC-315
Items
(CONSULT-II screen terms)DTC*1
Reference page
CONSULT-II
GST*
2ECM*3

EC-14Revision: June 2006
INDEX FOR DTC
2007 Versa
*1: 1st trip DTC No. is the same as DTC No.
*2: This number is prescribed by SAE J2012.KNOCK SEN/CIRC-B1 P0328 0328EC-315
LU-SLCT SOL/CIRC P1740 1740CVT-158
L/PRESS SOL/CIRC P0745 0745AT-145
MAF SEN/CIRCUIT P0101 0101EC-178
MAF SEN/CIRCUIT P0102 0102EC-187
MAF SEN/CIRCUIT P0103 0103EC-187
MULTI CYL MISFIRE P0300 0300EC-308
NATS MALFUNCTION P1610 - P1615 1610 - 1615BL-212
NO DTC IS DETECTED.
FURTHER TESTING
MAY BE REQUIRED.P0000 0000 —
O/R CLTCH SOL/CIRC P1760 1760AT-161
P-N POS SW/CIRCUIT P0850 0850EC-436
PNP SW/CIRC P0705 0705AT- 9 7 (A/T),
CVT-78
(CVT)
PRS CNT SOL/A FCTN P0746 0746CVT-118
PRS CNT SOL/B CIRC P0778 0778CVT-124
PRS CNT SOL/B FCTN P0776 0776CVT-121
PURG VOLUME CONT/V P0443 0443EC-354
PURG VOLUME CONT/V P0444 0444EC-362
PURG VOLUME CONT/V P0445 0445EC-362
SENSOR POWER/CIRC P0643 0643EC-430
SFT SOL A/CIRC P0750 0750 AT-151
SFT SOL B/CIRC P0755 0755AT-156
STEP MOTR CIRC P1777 1777CVT-164
STEP MOTR FNC P1778 1778CVT-168
TCC SOLENOID/CIRC P0740 0740AT-134
THERMSTAT FNCTN P0128 0128EC-218
TP SEN 1/CIRC P0222 0222EC-302
TP SEN 1/CIRC P0223 0223EC-302
TP SEN 2/CIRC P0122 0122EC-206
TP SEN 2/CIRC P0123 0123EC-206
TP SENSOR P2135 2135EC-526
TP SEN/CIRC A/T P1705 1705CVT-150
TR PRS SENS/A CIRC P0840 0840CVT-129
TR PRS SENS/B CIRC P0845 0845CVT-137
TW CATALYST SYS-B1 P0420 0420EC-334
VEH SPD SEN/CIR AT*5P0720 0720AT-107 (A/T).
CVT-95
(CVT)
VEH SPEED SEN/CIRC*
5P0500 0500EC-421
VENT CONTROL VALVE P0447 0447EC-369
VENT CONTROL VALVE P0448 0448EC-376
Items
(CONSULT-II screen terms)DTC*1
Reference page
CONSULT-II
GST*
2ECM*3