Check engine NISSAN TIIDA 2007 Service Repair Manual

TM-634
< REMOVAL AND INSTALLATION >[5MT: RS5F91R]
TRANSAXLE ASSEMBLY
8. Remove engine undercover.
9. Remove front drive shafts. Refer to FAX-10, "
Removal and Installation (Left Side)" and FAX-11, "Removal
and Installation (Right Side)".
NOTE:
Insert a suitable plug into side oil seal after removing front drive shaft.
10. Remove heat insulator and exhaust front tube. Refer to EX-5, "
Removal and Installation".
11. Disconnect position switch harness connector and then disconnect clip from rear housing.
12. Drain gear oil. Refer to TM-628, "
Draining".
13. Disconnect select cable and shift cable from transaxle assembly. Refer to TM-630, "
Removal and Installa-
tion".
14. Support engine assembly and transaxle assembly with a jack.
CAUTION:
When setting a jack, be careful not to bring it into contact with switch.
15. Remove engine mount through bolt-securing nut. Refer to EM-89, "
Exploded View".
16. Remove LH engine mount bracket (transaxle side) bolts.
17. Remove rear engine mount bracket and rear torque rod.
18. Remove transaxle assembly to engine assembly bolts.
19. Remove transaxle assembly from the vehicle.
CAUTION:
Secure transaxle assembly to a jack while removing it.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
When installing transaxle assembly, be careful not to bring transaxle input shaft into contact with
clutch cover.
 If transaxle is removed from the vehicle, always replace CSC. Refer to CL-11, "
Removal and Installation".
 When installing the transaxle assembly to the engine, install the
bolts following the standard below.
(A): M/T to engine
(B): Engine to M/T
 Bleed the air from the clutch hydraulic system. Refer to CL-8, "
Air Bleeding Procedure".
 After installation, check oil level, and check for leaks and loose mechanisms. Refer to TM-628, "
Inspection".
SCIA7084E
Bolt No. 1234
Quantity 2213
Bolt length “ ”
mm (in)55
(2.17)49
(1.93)69
(2.72)55
(2.17)
Tightening torque
N·m (kg-m, ft-lb)48.0
(4.9, 35)
PCIB1517E

TM-672
< ON-VEHICLE MAINTENANCE >[6MT: RS6F94R]
GEAR OIL
ON-VEHICLE MAINTENANCE
GEAR OIL
Exploded ViewINFOID:0000000001381632
Refer to TM-635, "Exploded View".
DrainingINFOID:0000000001381633
1. Start engine and let it run to warm up transaxle.
2. Stop engine. Remove drain plug (1) and then drain oil.
3. Set a new gasket on drain plug (1) and install it to transaxle and
tighten drain plug to the specified torque. Refer to TM-683,
"Exploded View".
CAUTION:
Do not reuse gasket.
RefillingINFOID:0000000001381634
1. Remove filler plug (1). Fill with new oil until oil level reaches the
specified limit near filler plug hole as shown.
2. After refilling oil, check oil level.
3. Set a new gasket on filler plug (1), then install it to transaxle and
tighten to the specified torque. Refer to TM-683, "
Exploded
View".
CAUTION:
Do not reuse gasket.
InspectionINFOID:0000000001381635
LEAKAGE
Make sure that oil is not leaking from transaxle or around it.
LEVEL
1. Remove filler plug (1) and check oil level at filler plug hole as
shown.
CAUTION:
Do not start engine while checking oil level.
2. Set a new gasket on filler plug (1) and install it to the transaxle
case.
CAUTION:
Do not reuse gasket.
3. Tighten filler plug to the specified torque. Refer to TM-683,
"Exploded View".
SCIA7622E
Oil grade and capacity : Refer to MA-19, "Fluids and
Lubricants".
SCIA7623E
SCIA7623E

TM-682
< REMOVAL AND INSTALLATION >[6MT: RS6F94R]
TRANSAXLE ASSEMBLY
K9K
Tighten bolts to the specified torque.
 Refer to CL-11, "
Removal and Installation" for CSC (Concentric Slave Cylinder) installation procedure.
 Refer to TM-674, "
Removal and Installation" for select cable and shift cable installation procedure.
 Bleed the air from the clutch hydraulic system. Refer to CL-8, "
Air Bleeding Procedure".
 After installation, check for oil leakage and oil level. Refer to TM-672, "
Inspection".
“ ” mm (in)60 (2.36) 50 (1.97)
Tightening torque
N·m (kg-m, ft-lb)62.0 (6.3, 46) Bolt symbol A B
: Transaxle to engine
: Engine to transaxle
Bolt symbol A B C
Quantity 2 2 4
“ ” mm (in)50 (1.97) 80 (3.15) 65 (2.56)
Tightening torque
N·m (kg-m, ft-lb)48 (4.9, 35)
JPDIC0054ZZ

A/C UNIT ASSEMBLY
VTL-13
< ON-VEHICLE REPAIR >[AUTOMATIC AIR CONDITIONER]
C
D
E
F
G
H
J
K
L
MA
B
VTL
N
O
P
7. Remove console box assembly. Refer to IP-11, "Removal and Installation"
8. Remove the instrument stay nuts (A) and harness clamps (B),
and then remove instrument stay (1).
9. Disconnect intake sensor connector (1).
10. Remove instrument panel and pad. Refer to IP-11, "
Removal and Installation".
11. Remove side ventilator ducts. Refer to VTL-23, "
Removal and Installation".
12. Remove center ventilator ducts. Refer to VTL-23, "
Removal and Installation".
13. Remove the side kicking plates. Refer to INT-20, "
Removal and Installation".
14. Disconnect the fuel filler door cable and the rear hatch door cable (if equipped).
15. Remove A/C unit assembly bolts, steering member bolts, steering column nuts and harness clips.
16. Remove steering member, and then remove A/C unit assembly.
INSTALLATION
Installation is in the reverse order of removal.
 Fill the cooling system with coolant. Refer to CO-11, "
Changing Engine Coolant" (HR16DE), CO-35, "Chang-
ing Engine Coolant" (MR18DE), CO-58, "Refilling" (K9K).
 Recharge the refrigerant. Refer to HA-29, "
HFC-134a (R-134a) Service Procedure".
CAUTION:
 Replace O-rings for A/C piping with new ones, and then apply compressor oil to it when installing it.
 When recharging refrigerant, check for leaks.
SJIA0646E
SJIA0690E
A/C unit assembly bolt : 6.9 N·m (0.7 kg-m, 61 in-lb)
Steering member bolt : 12 N·m (1.25 kg-m, 9 ft-lb)
Steering column nut : -Refer to ST-9, "
Removal and Installation".

VTL-38
< ON-VEHICLE REPAIR >[MANUAL AIR CONDITIONER]
A/C UNIT ASSEMBLY
7. Remove console box assembly. Refer to IP-11, "Removal and Installation" .
8. Remove instrument stay nuts (A) and harness clamps (B), and
then remove instrument stay (1).
9. Disconnect thermo control amp. connector (1).
10. Remove instrument panel and pad. Refer to IP-11, "
Removal and Installation".
11. Remove side ventilator ducts. Refer to VTL-48, "
Removal and Installation".
12. Remove center ventilator ducts. Refer to VTL-48, "
Removal and Installation".
13. Remove side kicking plates. Refer to INT-20, "
Removal and Installation".
14. Disconnect the fuel filler door cable and the rear hatch door cable.
15. Remove A/C unit assembly bolts, steering member bolts, steering column nuts and harness clips.
16. Remove steering member, and then remove A/C unit assembly.
INSTALLATION
Installation is in the reverse order of removal.
 Fill the cooling system. Refer to CO-11, "
Changing Engine Coolant" (HR16DE), CO-35, "Changing Engine
Coolant" (MR18DE), CO-58, "Refilling" (K9K).
 Recharge the refrigerant.
CAUTION:
 Replace O-rings for A/C piping with new ones, and apply compressor oil when installing.
 When recharging refrigerant, check for leaks.
SJIA0646E
SJIA0647E
A/C unit assembly bolt : 6.9 N·m (0.7 kg-m, 61 in-lb)
Steering member bolt : 12 N·m (1.25 kg-m, 9 ft-lb)
Steering column nut : Refer to ST-9, "
Removal and Installation".

WCS-30
< COMPONENT DIAGNOSIS >
PARKING BRAKE SWITCH SIGNAL CIRCUIT
PARKING BRAKE SWITCH SIGNAL CIRCUIT
DescriptionINFOID:0000000001722969
Transmits the parking brake switch signal to the combination meter.
Component Function CheckINFOID:0000000001724686
1.COMBINATION METER INPUT SIGNAL
1. Start engine.
2. Monitor “BRAKE” warning lamp while applying and releasing the parking brake.
>> Inspection End.
Diagnosis ProcedureINFOID:0000000001724687
1.CHECK PARKING BRAKE SWITCH CIRCUIT
1. Disconnect combination meter connector and parking brake
switch connector.
2. Check continuity between combination meter harness connector
M24 (A) terminal 10 and parking brake switch harness connec-
tor M17 (B) terminal 1.
3. Check continuity between combination meter harness connector
M24 (A) terminal 10 and ground.
Is the inspection result normal?
YES >> Inspection End.
NO >> Repair harness or connector.
Component InspectionINFOID:0000000001724688
1.CHECK PARKING BRAKE SWITCH
Check continuity between parking brake switch terminal 1 and switch
case ground.
Is the inspection result normal?
YES >> Inspection End.
NO >> Replace parking brake switch.BRAKE warning lamp
Parking brake applied : ON
Parking brake released : OFF
10 - 1 : Continuity should exist.
10 - Ground : Continuity should not exist.
AWNIA0273ZZ
Component Terminal Condition Continuity
Parking brake switch 1Parking brake applied Yes
Parking brake released No
AWNIA0018ZZ

WCS
THE PARKING BRAKE RELEASE WARNING CONTINUES SOUNDING, OR
DOES NOT SOUND
WCS-79
< SYMPTOM DIAGNOSIS >
C
D
E
F
G
H
I
J
K
L
MB A
O
P
THE PARKING BRAKE RELEASE WARNING CONTINUES SOUNDING, OR
DOES NOT SOUND
DescriptionINFOID:0000000001722967
 The parking brake warning buzzer sounds continuously during vehicle travel though the parking brake is
released
 The parking brake warning buzzer does not sound at all even though driving the vehicle with the parking
brake applied.
Diagnosis ProcedureINFOID:0000000001722968
1.CHECK PARKING BRAKE WARNING LAMP
1. Start the engine.
2. Check the operation of the brake warning lamp by operating the parking brake.
Is the inspection result normal?
YES >> Replace the combination meter. Refer to MWI-94, "Removal and Installation".
NO >> GO TO 2
2.CHECK PARKING BRAKE SWITCH SIGNAL CIRCUIT
Perform inspection of the parking brake switch signal circuit. Refer to WCS-30, "
Diagnosis Procedure".
Is the inspection result normal?
YES >> GO TO 3
NO >> Repair harness or connector.
3.CHECK PARKING BRAKE SWITCH UNIT
Perform a unit inspection for the parking brake switch. Refer to WCS-30, "
Component Inspection".
Is the inspection result normal?
YES >> Replace the combination meter. Refer to MWI-94, "Removal and Installation".
NO >> Replace the parking brake switch.Parking brake ON : ON
Parking brake OFF : OFF