engine NISSAN TIIDA 2007 Service Repair Manual

OIL PAN
EM-285
< ON-VEHICLE REPAIR >[K9K]
C
D
E
F
G
H
I
J
K
L
MA
EM
N
P O
10. Remove oil pan and transaxle joint bolts.
11. Support the engine bottom of the oil pan with a transmission jack
etc.
12. Remove oil pan bolts in reverse order as shown.
13. Insert seal cutter [SST: KV10111100 (—)] between upper oil pan
and cylinder block. Slide tool by tapping on the side of the tool
with a hammer.
CAUTION:
Exercise care not to damage mating surface.
14. Remove oil pan.
INSTALLATION
 Installation is in the reverse order of removal.
MBIB1039E
MBIB0575E
MBIB1257E
SEM365EA

EM-286
< ON-VEHICLE REPAIR >[K9K]
OIL PAN
1. Apply liquid gasket as shown.
 Use Genuine Liquid Gasket or equivalent.
2. Using suitable tool, align the oil pan with the cylinder block.
3. Install oil pan bolts in numerical order as shown.
NOTE:
Wait at least 30 minutes after oil pan is installed before filling
engine with engine oil.
InspectionINFOID:0000000001381494
INSPECTION AFTER REMOVAL
Clean oil pump assembly if any objects attached.
INSPECTION AFTER INSTALLATION
 Check the engine oil level. Refer to LU-26, "Inspection".
 Start the engine and make sure there are no leaks of engine oil. Refer to LU-26, "
Inspection".
MBIB0593E
MBIB0594E
: 14.0 N·m (1.4 kg-m, 10 ft-lb)
MBIB1257E

HIGH PRESSURE SUPPLY PUMP
EM-287
< ON-VEHICLE REPAIR >[K9K]
C
D
E
F
G
H
I
J
K
L
MA
EM
N
P O
HIGH PRESSURE SUPPLY PUMP
Exploded ViewINFOID:0000000001381495
Removal and InstallationINFOID:0000000001381496
REMOVAL
CAUTION:
 Be sure to read “Precautions for Diesel Equipment”. Refer to EM-253, "
Precaution for Diesel Equip-
ment".
 Wait until the fuel temperature drops before carrying out any work.
 Order the special high pressure injection circuit plug kit.
 It is strictly forbidden to remove any high pressure supply
pump sprocket marked number 070 575 (see diagram). If the
pump is being replaced, the pulley must be replaced.
1. Disconnect the battery.
2. Remove air duct (inlet). Refer to EM-269, "
Exploded View".
3. Remove engine cover.
4. Remove blow-by hose.
5. Remove charge air cooler hose and pipes. Refer to EM-270,
"Exploded View".
6. Remove the RH front tire. Refer to WT-6, "
Rotation".
7. Remove fender protector (RH). Refer to EXT-22, "
Removal and
Installation".
8. Remove drive belt. Refer to EM-263, "
Removal and Installation".
9. Support the engine using suitable tool.
10. Remove the timing belt. Refer to EM-291, "
Removal and Installation".
11. Remove the oil level gauge guide and plug the hole. Refer to EM-281, "
Exploded View".
12. Remove high pressure pipes protection cover (upper). Refer to EM-281, "
Exploded View".
13. Carefully disconnect:
 The connectors from the flow actuator,
 The connectors from the fuel temperature sensor,
 On the pump, the fuel supply and return pipes.
 The return pipe connecting the injectors with the pump.
14. Remove the injection tube connecting the pump to the rail. Refer to EM-281, "
Removal and Installation".
1. High pressure supply pump protec-
tor2. Stud bolt 3. High pressure supply pump
4. Engine cover bracket
E1BIA0119GB
MBIB9036E

ROCKER COVER
EM-289
< ON-VEHICLE REPAIR >[K9K]
C
D
E
F
G
H
I
J
K
L
MA
EM
N
P O
ROCKER COVER
Exploded ViewINFOID:0000000001381497
Removal and InstallationINFOID:0000000001381498
REMOVAL
1. Remove engine cover.
2. Remove air duct (inlet). Refer to EM-269, "
Exploded View".
3. Remove air duct (suction). Refer to EM-269, "
Exploded View".
4. Remove charge air cooler pipes and hoses. Refer to EM-270, "
Exploded View".
5. Disconnect and remove camshaft position sensor.
6. Remove fuel hose shield.
7. Disconnect electronic throttle control actuator. Refer to EM-272, "
Exploded View".
8. Remove blow-by hose.
9. Remove high pressure pipes protection cover (upper).
10. Unclip fuel injector spill hose from rocker cover.
11. Unclip timing belt upper cover.
12. Remove rocker cover.
NOTE:
Loosen bolts in the reverse order as shown.
INSTALLATION
1. Install new gasket to rocker cover.
1. Oil filler cap 2. Rocker cover 3. Gasket
4. Camshaft position sensor
E1BIA0006GB
E1BIA0048ZZ

TIMING BELT
EM-291
< ON-VEHICLE REPAIR >[K9K]
C
D
E
F
G
H
I
J
K
L
MA
EM
N
P O
TIMING BELT
Exploded ViewINFOID:0000000001381499
Removal and InstallationINFOID:0000000001381500
CAUTION:
 Apply new engine oil to parts marked in illustration before installation.
 Replace any belt that has been removed.
 Never turn the engine in the direction opposite to that of normal operation.
 When replacing the timing belt, be sure to replace the timing belt tensioner.
 Do not run the engine without the drive belts to avoid damaging the crankshaft pulley.
REMOVAL
1. Remove front wheel RH. Refer to WT-6, "Rotation".
2. Remove fender protector RH. Refer to EXT-22, "
Removal and Installation".
3. Remove engine cover.
4. Remove drive belt. Refer to EM-291, "
Removal and Installation".
5. Support the engine using suitable tool.
6. Remove RH engine torque rod.
7. Remove RH engine mounting support bracket and RH engine mounting insulator.
1. Timing belt inner cover 2. Timing belt 3. Camshaft sprocket
4. Camshaft sprocket stud bolt 5. Timing belt tensioner 6. Timing belt cover
7. Cylinder head suspended bracket 8. Crankshaft pulley 9. Crankshaft sprocket (timing belt)
10. Oil seal 11. Crankshaft cover 12. Gasket
A. 30.0 N·m (3.1 kg-m, 22 ft-lb) and 86 degrees
B. 120.0 N·m (12 kg-m, 89 ft-lb) and 95 degrees
E1BIA0022GB

TIMING BELT
EM-293
< ON-VEHICLE REPAIR >[K9K]
C
D
E
F
G
H
I
J
K
L
MA
EM
N
P O
13. Insert TDC set pin [SST: KV113B0110 (Mot.1430)] (A) into the
camshaft sprocket and cylinder head hole.
14. Screw in the TDC set pin [SST: KV113 B0130 (Mot. 1439)].
15. Turn the engine clockwise (timing side) until the crankshaft
touches the TDC set pin.
16. The pin [SST: KV113B0110 (Mot.1430)] (A) must engage in the
camshaft pulley and cylinder head holes.
17. Remove crankshaft position sensor. Refer to EM-284,
"Exploded View".
18. Remove crankshaft pulley (1).
CAUTION:
Do not remove bolt. Keep loosened bolt in place to protect
removed crankshaft pulley from dropping.
NOTE:
Insert flat-bladed screwdriver into position of crankshaft position
sensor to hold crankshaft from moving and loosen crankshaft
pulley bolt.
E1BIA0044ZZ
MBIB0394E
MBIB0395E
E1BIA0044ZZ
E1BIA0045ZZ

EM-294
< ON-VEHICLE REPAIR >[K9K]
TIMING BELT
19. Slacken the timing belt by loosening the bolt of tensioner (1),
then remove timing belt.
INSTALLATION
CAUTION:
It is essential to remove any dirt or grease from the end of the crankshaft, the bore of the crankshaft
sprocket and the bearing faces of the drive belt pulley to prevent any movement between the timing
sprockets and the crankshaft which would risk damaging the engine.
1. Install timing belt tensioner.
NOTE:
Put the timing belt tensioner tab (1) in the cylinder head groove.
2. Insert TDC set pin [SST: KV113B0110 (Mot. 1430)] (A) in the
camshaft pulley and cylinder head holes.
3. Check that high pressure supply pump sprocket mark (2) has
shifted one tooth to the right of vertical axle as shown.
4. Turn crankshaft to set TDC set pin [SST: KV113B0130 (Mot.
1489)] (the crankshaft groove (1) must be facing upwards).
5. Insert and tighten crankshaft pulley bolt with a spacer (1) (which
does not cover the timing sprocket mark).
E1BIA0046ZZ
E1BIA0060ZZ
E1BIA0061ZZ
E1BIA0059ZZ

EM-298
< ON-VEHICLE REPAIR >[K9K]
CAMSHAFT
CAMSHAFT
Exploded ViewINFOID:0000000001381501
Removal and InstallationINFOID:0000000001381502
CAUTION:
Apply new engine oil to parts marked in illustration before installation.
REMOVAL
1. Remove front wheel RH. Refer to WT-6, "Rotation".
2. Remove fender protector RH. Refer to EXT-22, "
Removal and Installation".
3. Remove rocker cover. Refer to EM-289, "
Removal and Installation".
4. Remove electronic throttle control actuator. Refer to EM-272, "
Exploded View".
5. Remove vacuum pump. Refer to EM-280, "
Removal and Installation".
6. Remove drive belt. Refer to EM-263, "
Removal and Installation".
7. Support the engine using suitable tool.
CAUTION:
Put a piece of wood or something similar as supporting surface to secure a completely stable con-
dition.
8. Remove timing belt. Refer to EM-291, "
Removal and Installation".
9. Remove camshaft brackets.
10. Remove camshaft.
11. Remove valve lifter.
INSTALLATION
1. Camshaft sprocket stud bolt 2. Camshaft sprocket 3. Oil seal
4. Camshaft bracket 5. Camshaft 6. Cylinder head suspended bracket
7. Valve lifter 8. Cap 9. Cylinder head
A. 30.0 N·m (3.1 kg-m, 22 ft-lb) and 86 degrees
E1BIA0023GB

EM-302
< REMOVAL AND INSTALLATION >[K9K]
ENGINE ASSEMBLY
REMOVAL AND INSTALLATION
ENGINE ASSEMBLY
Exploded ViewINFOID:0000000001381504
Removal and InstallationINFOID:0000000001381505
WARNING:
 Situate vehicle on a flat and solid surface.
 Place chocks at front and back of rear wheels.
 For engines not equipped with engine slingers, attach proper slingers and bolts described in PARTS
CATALOG.
CAUTION:
 Always be careful to work safely, avoid forceful or uninstructed operations.
 Do not start working until exhaust system and coolant are cool enough.
 If items or work required are not covered by the main engine section, follow the procedures in the
applicable sections.
 Always use the support point specified for lifting.
 Use either 2-pole lift type or separate type lift as best you can. If board-on type is used for unavoid-
able reasons, support at the rear axle jacking point with transmission jack or similar tool before
starting work, in preparation for the backward shift of center of gravity.
 For supporting points for lifting and jacking rear axle, refer to GI-48, "
Garage Jack and Safety Stand
and 2-Pole Lift" or GI-49, "Board-On Lift".
REMOVAL
Description of Work
1. Engine mounting insulator LH 2. Engine mounting frame support LH 3. Engine mounting bracket LH
4. Upper torque rod 5. Engine mounting insulator RH 6. Engine mounting bracket RH (upper)
7. Engine mounting bracket RH (lower) 8. Lower torque rod bracket 9. Lower torque rod
: Vehicle front
AWBIA0162GB

ENGINE ASSEMBLY
EM-303
< REMOVAL AND INSTALLATION >[K9K]
C
D
E
F
G
H
I
J
K
L
MA
EM
N
P O
Remove engine and transaxle assembly from vehicle down ward. Separate engine and transaxle.
Preparation
Remove the following parts.
 Battery ground cable.
 Engine undercover.
 LH and RH front wheels. Refer to WT-6, "
Rotation".
 LH and RH fender protectors. Refer to EXT-22, "
Removal and Installation".
Engine Room
1. Drain engine coolant. Refer to CO-58, "Draining".
CAUTION:
Perform when engine is cold.
2. Remove lower radiator hose. Refer to CO-62, "
Exploded View".
3. Drain transaxle fluid. Refer to TM-672, "
Draining".
4. Disconnect clutch tube at clutch housing and drain clutch fluid.
NOTE:
Cover clutch tube ends to prevent contamination.
5. Remove hood. Refer to DLK-214, "
Removal and Installation".
6. Remove cowl top cover and cowl top extension assembly. Refer to EXT-20, "
Removal and Installation".
7. Remove battery and battery trap. Refer to PG-6, "
Removal and Installation".
8. Disconnect engine room harness from the engine side and position aside.
9. Remove the air duct (inlet). Refer to EM-269, "
Exploded View".
10. Remove engine cover.
11. Remove blow-by hose.
12. Remove air cleaner case and air duct (suction). Refer to EM-269, "
Removal and Installation".
13. Remove reservoir tank and hoses. Refer to CO-62, "
Exploded View".
14. Remove charge air cooler hoses and tubes. Refer to EM-270, "
Exploded View".
15. Remove vacuum hose. Refer to EM-280, "
Removal and Installation".
16. Disconnect fuel feed and return hoses, and plug it to prevent fuel from draining.
17. Remove radiator upper hose. Refer to CO-62, "
Exploded View".
18. Disconnect heater hoses.
19. Disconnect transaxle side harness.
20. Disconnect breather hose transaxle side.
21. Disconnect shift cable and select cable. Refer to TM-674, "
Exploded View".
22. Remove cooling fan. Refer to CO-64, "
Removal and Installation".
23. Remove radiator. Refer to CO-62, "
Exploded View".
24. Disconnect all the body-side vacuum hoses and air hoses at engine side.
Vehicle Underbody
1. Remove drive shaft assembly RH and LH. Refer to Removal and Installation.
2. Remove exhaust front tube. Refer to EX-14, "
Component".
3. Remove drive belt. Refer to EM-263, "
Removal and Installation".
4. Remove A/C compressor and position aside.
NOTE:
Secure it to body with a rope to avoid putting load on A/C lines.
5. Remove lower torque rod. Refer to EM-302, "
Exploded View".
Removal