navigation NISSAN TIIDA 2007 Service User Guide

AV-12
< COMPONENT DIAGNOSIS >[AUDIO WITHOUT NAVIGATION]
STEERING SWITCH
1. Disconnect spiral cable connector M102.
2. Check continuity between spiral cable harness connector M30
(A) and M102 (B).
Does the spiral cable check OK?
YES >> Inspection End.
NO >> Replace spiral cable. Refer to XX-XX, "*****"
.
Spiral cable
Continuity
Connector Terminal Connector Terminal
M3024
M10220
Ye s 31 17
32 16
ALNIA0333GB

AV
MICROPHONE SIGNAL CIRCUIT
AV-13
< COMPONENT DIAGNOSIS >[AUDIO WITHOUT NAVIGATION]
C
D
E
F
G
H
I
J
K
L
MB A
O
P
MICROPHONE SIGNAL CIRCUIT
DescriptionINFOID:0000000001728771
Voice signals are transmitted from the microphone to the AV control unit using the microphone signal circuits.
Diagnosis ProcedureINFOID:0000000001728772
1.CHECK HARNESS BETWEEN AV CONTROL UNIT AND MICROPHONE
1. Turn ignition switch OFF.
2. Disconnect AV control unit connector and microphone connector.
3. Check continuity between AV control unit harness connector M44 and microphone harness connector
R15.
4. Check continuity between AV control unit harness connector M44 and ground.
Are the continuity test results as specified?
YES >> GO TO 2
NO >> Repair harness or connector.
2.CHECK MICROPHONE POWER SUPPLY
1. Connect AV control unit connector and microphone connector.
2. Turn ignition switch ON.
3. Check voltage between microphone harness connector R15 ter-
minal 4 and ground.
Is voltage reading approx. 5 volts?
YES >> GO TO 3
NO >> Replace AV control unit. Refer to XX-XX, "*****"
.
3.CHECK MICROPHONE SIGNAL
Check signal between AV control unit harness connector M44 terminals 27 and 28 with CONSULT-III or and
oscilliscope.
Te r m i n a l Te r m i n a l
Continuity
Connector Terminal Connector Terminal
M4427
R151
Ye s 28 2
29 4
Te r m i n a l
— Continuity
Connector Terminal
M447
Ground No 8
29
4 - Ground : Approx. 5V
WKIA5796E

AV-14
< COMPONENT DIAGNOSIS >[AUDIO WITHOUT NAVIGATION]
MICROPHONE SIGNAL CIRCUIT
Are voltage readings as specified?
YES >> Replace AV control unit. Refer to XX-XX, "*****".
NO >> Replace microphone. Refer to XX-XX, "*****"
.
Connector(+) (-)
Reference signal
Terminal Terminal
M44 27 28While speaking into MIC
PKIB5037J

AV
AV CONTROL UNIT
AV-15
< ECU DIAGNOSIS >[AUDIO WITHOUT NAVIGATION]
C
D
E
F
G
H
I
J
K
L
MB A
O
P
ECU DIAGNOSIS
AV CONTROL UNIT
Reference ValueINFOID:0000000001728621
TERMINAL LAYOUT
PHYSICAL VALUES
JPNIA0230ZZ
Te r m i n a l
(Wire color)Description
ConditionReference value
(Approx.)
+ – Signal nameInput/
Output
2
(L)3
(G)Sound signal front LH OutputIgnition
switch
ONVoice output
4
(LG)5
(Y)Sound signal rear LH OutputIgnition
switch
ONVoice output
6
(R)15
(B)Steering switch signal A InputIgnition
switch
ONKeep pressing SOURCE
switch. 0 V
Keep pressing SEEK UP
switch.1.7 V
Keep pressing VOL UP
switch.3.3 V
Except for above. 5 V
7
(R)Ground ACC power supply InputIgnition
switch
ACC−Battery voltage
11
(BR)12
(P)Sound signal front RH OutputIgnition
switch
ONVoice output
SKIB3609E
SKIB3609E
SKIB3609E

AV-16
< ECU DIAGNOSIS >[AUDIO WITHOUT NAVIGATION]
AV CONTROL UNIT
13
(O)14
(V)Sound signal rear RH OutputIgnition
switch
ONVoice output
15
(B)Ground Steering switch signal GND —Ignition
switch
ON—0 V
16
(Y)15
(B)Steering switch signal B InputIgnition
switch
ONKeep pressing switch.0 V
Keep pressing SEEK
DOWN switch.1.7 V
Keep pressing VOL DOWN
switch.3.3 V
Except for above. 5 V
17
(SB)— Immobilizer — — — —
18
(Y)GroundVehicle speed signal (8-
pulse) InputIgnition
switch
ONWhen vehicle speed is ap-
prox. 40 km/h (25MPH)
19
(LG)Ground Battery power supply InputIgnition
switch
OFF— Battery voltage
31
(B)Ground GND —Ignition
switch
ON—0 V
35
(B/W)36 Microphone signal InputIgnition
switch
ONSounds
36 Ground Microphone GND —Ignition
switch
ON—0 V
37
(L)36 Microphone VCC OutputIgnition
switch
ON—5 V
42 — Antenna signal Input — — —Terminal
(Wire color)Description
ConditionReference value
(Approx.)
+ – Signal nameInput/
Output
SKIB3609E
SKIA6649J
PKIB5037J

AV
AV CONTROL UNIT
AV-17
< ECU DIAGNOSIS >[AUDIO WITHOUT NAVIGATION]
C
D
E
F
G
H
I
J
K
L
MB A
O
P
Wiring DiagramINFOID:0000000001728622
ALNWA0138GB

AV-18
< ECU DIAGNOSIS >[AUDIO WITHOUT NAVIGATION]
AV CONTROL UNIT
ALNWA0139GB

AV
MULTI AV SYSTEM SYMPTOMS
AV-19
< SYMPTOM DIAGNOSIS >[AUDIO WITHOUT NAVIGATION]
C
D
E
F
G
H
I
J
K
L
MB A
O
P
SYMPTOM DIAGNOSIS
MULTI AV SYSTEM SYMPTOMS
Symptom TableINFOID:0000000001728624
RELATED TO AUDIO
RELATED TO HANDS FREE PHONE
 Check that the cellular phone is corresponding type (Bluetooth® enabled) when the hands free related mal-
function vehicle is in service before performing a diagnosis.
 There is a case that malfunction occurs due to the version change of the phone type, etc. even though it is a
corresponding type. Therefore, confirm it by changing the cellular phone to another corresponding type
phone, and check that it operates normally. It is necessary to distinguish whether the cause is the vehicle or
cellular phone. Check to ensure the customers phone is supported by checking the phone compatibility for
the hands free system.
Trouble diagnosis chart by symptom
RELATED TO STEERING SWITCH
Symptom Check items Possible malfunction location / Action to take
Audio sound is not heard.No sound from all speakers Audio unit (XX-XX, "*****"
)
Sound is not heard only from the specif-
ic places (Front RH, rear RH, front LH
and rear LH).Sound signal circuit of suspect system
Symptoms Check items Possible malfunction location / Action to take
Does not recognize cellular
phone connection. Repeat the registration of cellular phone. Audio unit (XX-XX, "*****"
)
Hands free phone cannot be
established. Hands free phone operation can be
made, but the communication cannot
be established.
 Hands free phone operation can be
performed, however, voice between
each other cannot be heard during the
conversation.Audio unit (XX-XX, "*****"
)
The other party's voice cannot
be heard by hands free phone.No sound from all speakers Audio unit (XX-XX, "*****"
)
Sound is not heard only from the specific
places (Front RH or front LH).Sound signal circuit (TEL voice)
Originating sound is not heard
by the other party with hands
free phone communication.Sound operation function is normal. Audio unit (XX-XX, "*****"
)
Sound operation function does not work. Microphone signal circuit (XX-XX, "*****"
)
Symptoms Possible malfunction location / Action to take
All steering switches are not operated. Steering switch signal ground circuit (XX-XX, "*****"
)
Only specified switch cannot be operated. Steering switch (XX-XX, "*****"
)
“MENU UP”, “VOL UP” and “SOURCE” switches are not op-
erated.Steering switch signal A circuit (XX-XX, "*****"
)
“ ”, “MENU DOWN” and “VOL DOWN” switches are not
operated.Steering switch signal B circuit (XX-XX, "*****"
)

AV-20
< SYMPTOM DIAGNOSIS >[AUDIO WITHOUT NAVIGATION]
NORMAL OPERATING CONDITION
NORMAL OPERATING CONDITION
DescriptionINFOID:0000000001728625
RELATED TO AUDIO
 The majority of the audio malfunctions are the result of outside causes (bad CD, electromagnetic interfer-
ence, etc.). Check the symptoms below to diagnose the malfunction.
 The vehicle itself can be a source of noise if noise prevention parts or electrical equipment is malfunctioning.
Check that noise is caused and/or changed by engine speed, ignition switch turned to each position, and
operation of each piece of electrical equipment. Then determine the cause.
NOTE:
 CD-R is not guaranteed to play because they can contain compressed audio (MP3, WMA) or could be incor-
rectly mastered by the customer on a computer.
 Check that the CDs carry the Compact Disc Logo. If not, the disc is not mastered to the red book Compact
Disc Standard and may not play.
Noise resulting from variations in field strength, such as fading noise and multi-path noise, or external noise from trains and other
sources, is not a malfunction.
NOTE:
 Fading noise: This noise occurs because of variations in the field strength in a narrow range due to mountains or buildings blocking
the signal.
 Multi-path noise: This noise results from a time difference between the broadcast waves directly from the station arriving at the
antenna and the waves reflected by mountains or buildings.
RELATED TO TELEPHONE
Symptoms Cause and Counter measure
Cannot playCheck that the CD was inserted correctly.
Check that the CD is scratched or dirty.
Check that there is condensation inside the player, and if there is, wait until the condensation is
gone (about 1 hour) before using the player.
The player will play correctly after it returns to the normal temperature if there is a temperature
increase error.
Only the music CD files (CD-DA data) will be played if there is a mixture of music CD files (CD-
DA data) and MP3/WMA files on a CD.
Files with extensions other than “.MP3”, “.WMA”, “.mp3”, or “.wma” cannot be played.
Check that the finalization process, such as session close and disc close, is done for the disc.
Check that the CD is protected by copyright.
Poor sound quality Check that the CD is scratched or dirty.
It takes a relatively long time before
the music starts playing.If there are many folder or file levels on the MP3/WMA CD, or if it is a multisession disc, some
time may be required before the music starts playing.
The songs do not play back in the
desired order.The playback order is the order in which the files were written by the software, so the files might
not play in the desired order.
Symptom Possible cause Possible solution
The system does not recognize the
command.
The system recognizes the com-
mand incorrectly.The interior of the vehicle is too noisy.Close the windows or have other occupants
be quiet.
The volume of the voice is too low. Speak louder.
Pronunciation is unclear. Speak clearly.
Voice recognition mode is not yet ready to speak.Push the release “ ” on the steering
switch, and speak a command after the
tone sounds.
5 seconds or more have passed after pushed and
released “ ” on the steering switch.Make sure to speak a command within
5seconds after push and release “ ” on
the steering switch.

AV
PRECAUTIONS
AV-21
< PRECAUTION >[AUDIO WITHOUT NAVIGATION]
C
D
E
F
G
H
I
J
K
L
MB A
O
P
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"
INFOID:0000000001731028
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. Information necessary to service the system safely is included in the “SRS AIRBAG” and
“SEAT BELT” of this Service Manual.
WARNING:
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
 Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see the “SRS AIRBAG”.
 Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or har-
ness connectors.