trunk release NISSAN TIIDA 2007 Service Repair Manual

BCS-48
< ECU DIAGNOSIS >
BCM (BODY CONTROL MODULE)
527
(GR)Ground PTC relay 2 control Output Ignition ONPTC heater 2 ON 0V
PTC heater 2 OFF Battery voltage
58
(Y)Ground Door unlock sensor Input Driver doorLock Battery voltage
Unlock 0V
59
(O)Ground Rear door switch LH InputRear door
switch LHOFF (When rear door LH
closed) Battery voltage
ON (When rear door LH
opened)0V
60
(GR)Ground Rear door switch RH InputRear door
switch RHOFF (When rear door RH
closed) Battery voltage
ON (When rear door RH
opened)0V
61
3
(O)Ground A/C switch Output A/C switchNot pressed Battery voltage
Pressed 0V
63
(R)GroundLight & rain sensor
serial linkOutputIgnition switch OFF Battery voltage
Ignition switch ON
64
7
(O)Ground PTC relay 1 control Output Ignition ONPTC heater 1 ON 0V
PTC heater 1 OFF Battery voltage
65
(V)Ground Turn signal LH OutputIgnition switch
ONTurn signal switch OFF 0V
Turn signal switch LH
66
(W)Ground Turn signal RH OutputIgnition switch
ONTurn signal switch OFF 0V
Turn signal switch RH
67
(G)GroundDoor unlock (pas-
senger and rear
doors)OutputDoor lock/un-
lock switchPressed to the unlock side Battery voltage
Pressed to the lock side 0V
68
1
(R)GroundBack door lock actu-
atorOutputBack door
opener switchPressed Battery voltage
Not pressed 0V
68
2
(R)GroundTrunk release sole-
noidOutputTrunk lid opener
switchPressed Battery voltage
Not pressed 0V Te r m i n a l N o .
(Wire color)Description
ConditionReference Value
(Approx.)
Signal nameInput/
Output +−
MKIB0173E
SKIA1120J
SKIA1120J

TRUNK LID OPENER
DLK-37
< FUNCTION DIAGNOSIS >[WITH I-KEY, WITHOUT SUPER LOCK]
C
D
E
F
G
H
I
J
L
MA
B
DLK
N
O
P
TRUNK LID OPENER
TRUNK LID OPENER SWITCH
TRUNK LID OPENER SWITCH : System DiagramINFOID:0000000001451786
TRUNK LID OPENER OPERATION
TRUNK LID OPENER SWITCH : System DescriptionINFOID:0000000001451787
TRUNK LID OPENER OPERATION
When trunk lid opener switch is pressed, BCM opens trunk release solenoid.
NOTE:
Trunk release solenoid is not for locking the back door. The function is only to open the trunk.
OPERATION CONDITION
If the following conditions are not satisfied, trunk release operation is not performed.
TRUNK LID OPENER SWITCH : Component Parts LocationINFOID:0000000001451788
ALKIA0717GB
Trunk lid opener switch operation Operation condition
Trunk release solenoid Vehicle speed is less than 5 km/h (3 MPH).
 All doors are unlocked.
ALKIA0819ZZ
1. BCM M18, M20
(view with glove box removed) 2. Trunk lamp switch and trunk release solenoid
B663. Trunk lid opener switch B61

DLK-38
< FUNCTION DIAGNOSIS >[WITH I-KEY, WITHOUT SUPER LOCK]
TRUNK LID OPENER
TRUNK LID OPENER SWITCH : Component Description
INFOID:0000000001451789
Item Function
BCM Controls the trunk lid opener switch function.
Trunk lid opener switch Transmits trunk lid opener switch operation signal to BCM.
Trunk release solenoid Opens the trunk with the trunk release solenoid signal from BCM.
Combination meter Transmits vehicle speed signal to BCM via CAN communication.

DLK-52
< FUNCTION DIAGNOSIS >[WITH I-KEY, WITHOUT SUPER LOCK]
DIAGNOSIS SYSTEM (BCM)
CONSULT-III performs the following functions via CAN communication with BCM.
DATA MONITOR
TRUNK
TRUNK : CONSULT-III Function (BCM - TRUNK)INFOID:0000000001396505
APPLICATION ITEM
CONSULT-III performs the following functions via CAN communication with BCM.
DATA MONITOR
ACTIVE TEST
Diagnosis mode Function Description
DATA MONITOR The BCM input/output signals are displayed.
Monitor Item Condition
IGN ON SW Indicates [ON/OFF] condition of ignition switch in ON position.
ACC ON SW Indicates [ON/OFF] condition of ignition switch in ACC position.
KEY ON SW Indicates [ON/OFF] condition of key switch.
PUSH SW Indicates [ON/OFF] condition of ignition knob switch.
I-KEY LOCK Indicates [ON/OFF] condition of lock signal from Intelligent Key.
I-KEY UNLOCK Indicates [ON/OFF] condition of unlock signal from Intelligent Key.
Diagnosis mode Function Description
DATA MONITOR The BCM input/output signals are displayed.
ACTIVE TEST The signals used to activate each device are forcibly supplied from Intelligent Key unit.
Monitor Item Condition
IGN ON SW Indicates [ON/OFF] condition of ignition switch in ON position.
KEY ON SW Indicates [ON/OFF] condition of key switch.
PUSH SW Indicates [ON/OFF] condition of ignition knob switch.
TRNK OPNR SW Indicates [ON/OFF] condition of back door/trunk opener switch.
VEHICLE SPEEDDisplays the vehicle speed signal received from combination meter by numerical value
[km/h].
Test item Description
TRUNK/GLASS HATCH This test is able to check back door actuator/trunk release solenoid operation [ON/OFF].

DLK-54
< FUNCTION DIAGNOSIS >[WITH I-KEY, WITHOUT SUPER LOCK]
DIAGNOSIS SYSTEM (INTELLIGENT KEY UNIT)
ACTIVE TEST
Monitor Item Condition
PUSH SW Indicates [ON (pressed)/OFF (released)] condition of ignition knob switch.
KEY SW Indicates [ON (inserted)/OFF (removed)] condition of key switch.
DR REQ SW Indicates [ON (pressed)/OFF (released)] condition of door request switch (driver side).
AS REQ SW Indicates [ON (pressed)/OFF (released)] condition of door request switch (passenger side).
BD/TR REQ SW Indicates [ON (pressed)/OFF (released)] condition of back door/trunk request switch.
IGN SWIndicates [ON (ON or START position)/OFF (other than ON and START position)] condition of
ignition switch ON position.
ACC SW Indicates [ON/OFF] condition of ignition switch ACC position.
STOP LAMP SW Indicates [ON/OFF] condition of stop lamp switch.
DOOR LOCK SIG Indicates [ON/OFF] condition of LOCK signal from Intelligent Key.
DOOR UNLOCK SIG Indicates [ON/OFF] condition of UNLOCK signal from Intelligent Key.
DOOR SW DRIndicates [OPEN/CLOSE] condition of front door switch (driver side) from BCM via CAN com-
munication.
DOOR SW ASIndicates [OPEN/CLOSE] condition of front door switch (passenger side) from BCM via CAN
communication.
DOOR SW RRIndicates [OPEN/CLOSE] condition of rear door switch (RH) from BCM via CAN communica-
tion.
DOOR SW RLIndicates [OPEN/CLOSE] condition of rear door switch (LH) from BCM via CAN communica-
tion.
DOOR BK SW Indicates [OPEN/CLOSE] condition of back door switch from BCM via CAN communication.
VEHICLE SPEED Displays the vehicle speed signal received from combination meter by numerical value [km/h].
Test item Description
DOOR LOCK/UNLOCKThis test is able to check door lock/unlock operation.
 ALL UNLK: All door lock actuators are unlocked.
 DR UNLK: Door lock actuator (driver side) is unlocked.
 AS UNLK: Door lock actuator (passenger side) is unlocked.
 BK UNLK: This item is indicated, but inactive.
 LOCK: All door lock actuator is locked.
ANTENNAThis test is able to check Intelligent Key antenna operation.
When the following condition are met, hazard warning lamps flash.
 ROOM ANT1: Inside key antenna (console) detects Intelligent Key, when “ROOM
ANT1” is selected.
 ROOM ANT2: Inside key antenna (instrument center/rear seat) detects Intelligent
Key, when “ROOM ANT2”is selected.
 DRIVER ANT: Outside key antenna (driver side) detects Intelligent Key, when “DRIV-
ER ANT” is selected.
 ASSIST ANT: Outside key antenna (passenger side) detects Intelligent Key, when
“ASSIST ANT” is selected.
 BK DOOR ANT: Outside key antenna (rear bumper) detects Intelligent Key, when “BK
DOOR ANT” is selected.
OUTSIDE BUZZERThis test is able to check Intelligent Key warning buzzer(s) operation.
ON
OFF
INSIDE BUZZERThis test is able to check warning chime in combination meter operation.
 TAKE OUT: Take away warning chime sounds.
 KNOB: Ignition knob switch warning chime sounds.
 KEY: Key warning chime sounds.
OFF

TRUNK REQUEST SWITCH
DLK-91
< COMPONENT DIAGNOSIS >[WITH I-KEY, WITHOUT SUPER LOCK]
C
D
E
F
G
H
I
J
L
MA
B
DLK
N
O
P
TRUNK REQUEST SWITCH
DescriptionINFOID:0000000001396532
Transmits lock/unlock operation to Intelligent Key unit.
Component Function CheckINFOID:0000000001396533
1.CHECK FUNCTION
With CONSULT-III
Check door request switch “BD/TR REQ SW” in “Data Monitor” mode.
Is the inspection result normal?
YES >> Door request switch is OK.
NO >> Refer to DLK-91, "
Diagnosis Procedure".
Diagnosis ProcedureINFOID:0000000001396534
1.CHECK INTELLIGENT KEY UNIT INPUT SIGNAL
1. Turn ignition switch OFF.
2. Check voltage between Intelligent Key unit harness connector
and ground.
Is the inspection result normal?
YES >> GO TO 6.
NO >> GO TO 2.
2.CHECK TRUNK REQUEST SWITCH CIRCUIT
1. Disconnect Intelligent Key unit and trunk request switch.
Monitor item Condition
BD/TR REQ SWDoor request switch is pressed :ON
Door request switch is released :OFF
ALKIA0745ZZ
Te r m i n a l
trunk request
switch conditionVoltage (V)
(Approx.) (+)
(–)
Intelligent Key unit
connectorTe r m i n a l
M52 29 GroundPressed 0
Released 5

TRUNK REQUEST SWITCH
DLK-93
< COMPONENT DIAGNOSIS >[WITH I-KEY, WITHOUT SUPER LOCK]
C
D
E
F
G
H
I
J
L
MA
B
DLK
N
O
P
Component InspectionINFOID:0000000001396535
1.CHECK TRUNK REQUEST SWITCH
Check trunk request switch.
Is the inspection result normal?
YES >> Door request switch is OK.
NO >> Replace trunk request switch. Refer to XX-XX, "*****"
.
WIIA1186E
Te r m i n a l
Trunk request switch condition Continuity
Trunk request switch
12Pressed Yes
Released No

DLK-94
< COMPONENT DIAGNOSIS >[WITH I-KEY, WITHOUT SUPER LOCK]
TRUNK LID UNLOCK SWITCH
TRUNK LID UNLOCK SWITCH
DescriptionINFOID:0000000001507341
Detects trunk open/close condition.
Component Function CheckINFOID:0000000001507342
1.CHECK FUNCTION
With CONSULT-III
Check TRNK/HAT MNTR in Data Monitor mode with CONSULT-III.
Is the inspection result normal?
YES >> Trunk lamp switch is OK.
NO >> Refer to DLK-94, "
Diagnosis Procedure".
Diagnosis ProcedureINFOID:0000000001507343
1.CHECK TRUNK LAMP SWITCH INPUT SIGNAL
1. Turn ignition switch OFF.
2. Check voltage between BCM connector and ground.
Is the inspection result normal?
YES >> GO TO 4
NO >> GO TO 2
2.CHECK TRUNK LAMP SWITCH CIRCUIT
1. Disconnect BCM and trunk lamp switch and trunk release solenoid connectors.
Monitor item Condition
TRNK/HAT MNTROPEN : ON
CLOSE : OFF
ALKIA0755ZZ
Te r m i n a l s
Trunk
conditionVoltage (V)
(Approx.) (+)
(–)
BCM connector Terminal
M18 10 GroundOPEN 0
CLOSE Battery voltage

TRUNK LID UNLOCK SWITCH
DLK-95
< COMPONENT DIAGNOSIS >[WITH I-KEY, WITHOUT SUPER LOCK]
C
D
E
F
G
H
I
J
L
MA
B
DLK
N
O
P
2. Check continuity between BCM connector (A) M18 terminals10
and trunk lamp switch and trunk release solenoid connector (B)
B66 terminal 3.
3. Check continuity between BCM connector and ground.
Is the inspection result normal?
YES >> GO TO 3
NO >> Repair or replace harness between BCM and trunk lamp switch and trunk release solenoid.
3.CHECK TRUNK LAMP SWITCH GROUND CIRCUIT
Check continuity between trunk lamp switch and trunk release sole-
noid connector and ground.
Is the inspection result normal?
YES >> GO TO 4
NO >> Repair or replace trunk lamp switch and trunk release solenoid ground circuit.
4.CHECK BCM OUTPUT SIGNAL
1. Connect BCM connector.
ALKIA0762ZZ
BCM connector TerminalTrunk lamp switch and trunk release
solenoid connectorTerminal Continuity
M18 10 B66 3 Yes
BCM connector Terminal
GroundContinuity
M18 10 No
ALKIA0763ZZ
Trunk lamp switch and trunk release
solenoid connectorTe r m i n a l
GroundContinuity
B66 1 Yes

DLK-96
< COMPONENT DIAGNOSIS >[WITH I-KEY, WITHOUT SUPER LOCK]
TRUNK LID UNLOCK SWITCH
2. Check voltage between BCM connector and ground.
Is the inspection result normal?
YES >> GO TO 5
NO >> Replace BCM. Refer to XX-XX, "*****"
.
5.CHECK TRUNK ROOM LAMP SWITCH
Refer to DLK-96, "
Component Inspection".
Is the inspection result normal?
YES >> GO TO 6
NO >> Replace trunk lamp switch and trunk release solenoid.
6.CHECK INTERMITTENT INCIDENT
Refer to XX-XX, "*****"
.
>> INSPECTION END.
Component InspectionINFOID:0000000001507344
1.CHECK TRUNK LAMP SWITCH
1. Turn ignition switch OFF.
2. Check trunk lamp switch.
Is the inspection result normal?
YES >> INSPECTION END.
ALKIA0755ZZ
Te r m i n a l s
Voltage (V)
(Approx.) (+)
(–)
BCM connector Terminal
M18 10 Ground Battery voltage
ALKIA0764ZZ
Te r m i n a l
Trunk condition Continuity
Trunk lamp switch and trunk release solenoid
13OPEN Yes
CLOSE No