trunk NISSAN TIIDA 2007 Service Owner's Guide

WARNING FUNCTION
DLK-39
< FUNCTION DIAGNOSIS >[WITH I-KEY, WITHOUT SUPER LOCK]
C
D
E
F
G
H
I
J
L
MA
B
DLK
N
O
P
WARNING FUNCTION
System DiagramINFOID:0000000001396494
INTELLIGENT KEY WARNING OPERATION
BACK DOOR/TRUNK LID OPEN WARNING OPERATION
System DescriptionINFOID:0000000001396495
DESCRIPTION
The warning functions are as follows and are given to the user as warning information and warnings using
combinations of Intelligent Key warning buzzer(s), key warning lamps and buzzer (built in combination meter).
INTELLIGENT KEY WARNING OPERATION
Once one of the following conditions below is established, alert or warning will be executed.
JMKIA0409GB
ALKIA0718GB

WARNING FUNCTION
DLK-41
< FUNCTION DIAGNOSIS >[WITH I-KEY, WITHOUT SUPER LOCK]
C
D
E
F
G
H
I
J
L
MA
B
DLK
N
O
P
KEY WARNING LAMP & LOCK WARNING LAMP
The key indicator and lock indicator indicates Intelligent Key system status.
Operation Condition
BACK DOOR/TRUNK OPEN WARNING OPERATION
When back door (hatchback) or trunk lid (sedan) opener switch is operated, when door lock is locked with door
lock and unlock switch, speed sensing lock or only driver side is unlocked with anti-hijack function, the buzzer
(built in combination meter) will sound.
KEY REMINDER OPERATION
 The buzzer (combination meter) will sound and the doors will not lock if the door lock and unlock switch is
pressed while the driver door is open and mechanical key is inserted into ignition key cylinder.
 The buzzer (combination meter) will sound and the doors will not lock if the door lock and unlock switch is
pressed while any door other than the driver door is open.
Door lock op-
eration warn-
ingRequest
switch opera-
tionWhen request switch is pushed (lock op-
eration) under the following conditions.
 Door switch: ON (Any door is open).
 Ignition switch is in ACC or OFF posi-
tion or ignition knob is pressed in
LOCK position or mechanical key is
inserted into ignition key cylinder.
 Intelligent Key is inside vehicle.——Active for 2
seconds
(pipipi···)
Intelligent Key
button opera-
tionWhen Intelligent Key button is pushed
(lock operation) under the following con-
ditions.
 Door switch: ON (Any door is open).
 Ignition switch is in ACC or OFF posi-
tion or ignition knob is pressed in
LOCK position or mechanical key is
inserted into ignition key cylinder.——Active for 2
seconds
(pipipi···)
Intelligent Key low battery
warningWhen Intelligent Key battery voltage is
low, Intelligent Key unit is detected after
ignition switch is turned ON.“KEY”
(GREEN blink-
ing for 30 sec-
onds)—— Warning/Information functions Operation conditions Warning lampWarning chime
Combination
meter buzzerIntelligent Key
warning buzz-
er(s)
Behavior of lamps Operation condition
KEYGREENLightingAll the following conditions are satisfied.
 Ignition knob is pushed in LOCK position. (Ignition knob switch is ON)
 Ignition key is removed from ignition key cylinder. (Key switch is OFF)
 Intelligent Key is detected inside of the vehicle.
 KEY RED lighting/blinking conditions are not satisfied.
Blinking while Intelligent Key low battery warning is operating.
REDLightingAll the following conditions are satisfied.
 Ignition knob is pushed. (Ignition knob switch is ON)
 Ignition key is removed from ignition key cylinder. (Key switch is OFF)
 Intelligent Key is not detected inside of the vehicle.
BlinkingAll the following conditions are satisfied.
 Take away warning is operating.
 KEY RED lighting condition is not satisfied.
LOCK Blinking While OFF position warning is operating.
KEY(RED) and LOCK lightingAll the following conditions are satisfied.
 Ignition switch is ON.
 Steering lock ID is NG.

WARNING FUNCTION
DLK-43
< FUNCTION DIAGNOSIS >[WITH I-KEY, WITHOUT SUPER LOCK]
C
D
E
F
G
H
I
J
L
MA
B
DLK
N
O
PALKIA0815ZZ
1. Combination meter M24 2. Key warning lamp (combination meter) 3. Lock warning lamp (combination meter)
4. Stop lamp switch E13
(view with instrument panel LH re-
moved)5. Steering lock solenoid M6
(bottom view of steering column)6. Key switch and ignition knob switch (A/
T) M32
7. Key switch and ignition knob
switch (M/T) M328. Instrument panel antenna M10
(view with glove box removed)9. BCM M18, M19, M20
10. Intelligent Key Unit M52 11. Intelligent key warning buzzer (driver side)
D6 (view with front door finisher removed)12. Front outside antenna (driver side) D10
(Passenger side) D106
13. Front door request switch (driver
side) D5
(Passenger side) D10314. Door unlock sensor D14
[Front door lock actuator (driver side)]15. Front door switch (driver side) B34
(Passenger side) B29
16. Front console antenna B45
(view with front console removed)17. Rear door switch LH B71
RH B5318. Rear floor antenna B46
(behind rear seat)
19. Trunk request switch B67
(sedan)20. Rear bumper antenna B81
(view with rear fascia removed)21. Intelligent Key warning buzzer (trunk)
B82 (sedan)
(view with trunk finisher LH removed)
22. Back door request switch D406
(hatchback)23. Back door lock assembly (back door switch)
D405 (hatchback view with back door open)

DLK-44
< FUNCTION DIAGNOSIS >[WITH I-KEY, WITHOUT SUPER LOCK]
WARNING FUNCTION
Component Description
INFOID:0000000001396497
* : Sedan only
**: Hatchback onlyItem Function
BCM Controls the warning function with Intelligent Key unit.
Intelligent Key unit Controls the warning function with BCM.
Key switch Detects that mechanical key is inserted into ignition key cylinder.
Door switch Detects door state (open or closed).
Door lock and unlock switch Transmits door lock and unlock signal to BCM.
Intelligent Key unitRequests to turn ON hazard warning lamp to BCM and turn signal indicator to
combination meter.
Combination meterTurns ON the LOCK indicator, KEY indicator, turn signal indicator and buzzer
(built in combination meter) by the request from Intelligent Key unit via CAN com-
munication.
Intelligent Key warning buzzer (driver side) Sounds by the request from Intelligent Key unit.
Intelligent Key warning buzzer (trunk)
*Sounds by the request from Intelligent Key unit.
Back door opener switch
**Transmits back door open signal to BCM
Trunk lid opener switch
*Transmits trunk open signal to BCM

DLK-48
< FUNCTION DIAGNOSIS >[WITH I-KEY, WITHOUT SUPER LOCK]
HAZARD AND BUZZER REMINDER FUNCTION
ALKIA0815ZZ
1. Combination meter M24 2. Key warning lamp (combination meter) 3. Lock warning lamp (combination meter)
4. Stop lamp switch E13
(view with instrument panel LH re-
moved)5. Steering lock solenoid M6
(bottom view of steering column)6. Key switch and ignition knob switch (A/
T) M32
7. Key switch and ignition knob
switch (M/T) M328. Instrument panel antenna M10
(view with glove box removed)9. BCM M18, M19, M20
10. Intelligent Key Unit M52 11. Intelligent key warning buzzer (driver side)
D6 (view with front door finisher removed)12. Front outside antenna (driver side) D10
(Passenger side) D106
13. Front door request switch (driver
side) D5
(Passenger side) D10314. Door unlock sensor D14
[Front door lock actuator (driver side)]15. Front door switch (driver side) B34
(Passenger side) B29
16. Front console antenna B45
(view with front console removed)17. Rear door switch LH B71
RH B5318. Rear floor antenna B46
(behind rear seat)
19. Trunk request switch B67
(sedan)20. Rear bumper antenna B81
(view with rear fascia removed)21. Intelligent Key warning buzzer (trunk)
B82 (sedan)
(view with trunk finisher LH removed)
22. Back door request switch D406
(hatchback)23. Back door lock assembly (back door switch)
D405 (hatchback view with back door open)

HAZARD AND BUZZER REMINDER FUNCTION
DLK-49
< FUNCTION DIAGNOSIS >[WITH I-KEY, WITHOUT SUPER LOCK]
C
D
E
F
G
H
I
J
L
MA
B
DLK
N
O
P
Component DescriptionINFOID:0000000001396501
*: Sedan onlyItem Function
BCM Controls the hazard and buzzer reminder function with Intelligent Key unit.
Intelligent Key unit Controls the hazard and buzzer reminder function with BCM.
Combination meterTurns ON the LOCK indicator, KEY indicator, turn signal indicator and buzzer
(built in combination meter) by the request from Intelligent Key unit via CAN com-
munication.
Intelligent Key warning buzzer (driver side) Sounds by the request signal from Intelligent Key unit via CAN communication.
Intelligent Key warning buzzer (trunk)
*Sounds by the request signal from Intelligent Key unit via CAN communication.

DLK-50
< FUNCTION DIAGNOSIS >[WITH I-KEY, WITHOUT SUPER LOCK]
DIAGNOSIS SYSTEM (BCM)
DIAGNOSIS SYSTEM (BCM)
COMMON ITEM
COMMON ITEM : CONSULT-III Function (BCM - COMMON ITEM)INFOID:0000000001396502
APPLICATION ITEM
CONSULT-III performs the following functions via CAN communication with BCM.
SYSTEM APPLICATION
BCM can perform the following functions for each system.
NOTE:
It can perform the diagnosis modes except the following for all sub system selection items.
DOOR LOCK
DOOR LOCK : CONSULT-III Function (BCM - DOOR LOCK)INFOID:0000000001396503
BCM CONSULT-III FUNCTION
CONSULT-III performs the following functions via CAN communication with BCM.
Diagnosis mode Function Description
WORK SUPPORT Changes the setting for each system function.
SELF-DIAG RESULTS Displays the diagnosis results judged by BCM. Refer to XX-XX, "*****"
.
CAN DIAG SUPPORT MNTR Monitors the reception status of CAN communication viewed from BCM.
DATA MONITOR The BCM input/output signals are displayed.
ACTIVE TEST The signals used to activate each device are forcibly supplied from BCM.
ECU IDENTIFICATION The BCM part number is displayed.
CONFIGURATION Enables to read and save the vehicle specification.
 Enables to write the vehicle specification when replacing BCM.
System Sub system selection itemDiagnosis mode
WORK SUPPORT DATA MONITOR ACTIVE TEST
—BCM×
Door lock DOOR LOCK×××
Rear window defogger REAR DEFOGGER××
Warning chime BUZZER××
Interior room lamp timer INT LAMP×××
Remote keyless entry system MULTI REMOTE ENT×××
Exterior lamp HEAD LAMP×××
Wiper and washer WIPER×××
Turn signal and hazard warning lamps FLASHER××
Air conditioner AIR CONDITONER×
Intelligent Key system INTELLIGENT KEY×
Combination switch COMB SW×
Immobilizer IMMU××
Interior room lamp battery saver BATTERY SAVER×××
Trunk open TRUNK×
Vehicle security system THEFT ALM×××
Signal buffer system SIGNAL BUFFER××
PTC heater system PTC HEATER××

DIAGNOSIS SYSTEM (BCM)
DLK-51
< FUNCTION DIAGNOSIS >[WITH I-KEY, WITHOUT SUPER LOCK]
C
D
E
F
G
H
I
J
L
MA
B
DLK
N
O
P
DATA MONITOR
ACTIVE TEST
WORK SUPPORT
INTELLIGENT KEY
INTELLIGENT KEY : CONSULT-III Function (BCM - INTELLIGENT KEY)INFOID:0000000001396504
BCM CONSULT-III FUNCTION
Diagnosis mode Function Description
WORK SUPPORT Changes the setting for each system function.
DATA MONITOR The BCM input/output signals are displayed.
ACTIVE TEST The signals used to activate each device are forcibly supplied from BCM.
Monitor Item Condition
IGN ON SW Indicates [ON/OFF] condition of ignition switch in ON position.
ACC ON SW Indicates [ON/OFF] condition of ignition switch in ACC position.
PUSH SW Indicates [ON/OFF] condition of ignition knob switch.
KEY ON SW Indicates [ON/OFF] condition of key switch.
CDL LOCK SW Indicates [ON/OFF] condition of door lock and unlock switch.
CDL UNLOCK SW Indicates [ON/OFF] condition of door lock and unlock switch.
DOOR SW-DR Indicates [ON/OFF] condition of front door switch (driver side).
DOOR SW-AS Indicates [ON/OFF] condition of front door switch (passenger side).
DOOR SW-RR Indicates [ON/OFF] condition of rear door switch RH.
DOOR SW-RL Indicates [ON/OFF] condition of rear door switch LH.
BACK DOOR SW Indicates [ON/OFF] condition of back door switch.
BD/TR OPNR SW Indicates [ON/OFF] condition of back door/trunk opener switch.
I-KEY LOCK Indicates [ON/OFF] condition of lock signal from Intelligent Key.
I-KEY UNLOCK Indicates [ON/OFF] condition of unlock signal from Intelligent Key.
UNLOCK WITH DR This item is indicated, but not monitored.
UNLOCK SHOCKIndicates [ON/OFF] condition of signal from air bag diagnosis unit.
 ON: During the unlock operation interlock with air bag.
 OFF: Other than above.
SHOCK SENSORIndicates [NOMAL/ON/OFF] condition of circuit between BCM and air bag diagnosis sensor unit.
 NORMAL: Ignition switch ON. (BCM is receiving normal condition signal from air bag diagno-
sis sensor unit.)
 ON: During the receiving of air bag deployment signal from air bag diagnosis sensor unit.
 OFF: After the receiving of air bag deployment signal from air bag diagnosis sensor unit.
VEHICLE SPEED Displays the vehicle speed signal received from combination meter by numerical value [km/h].
Test item Description
DOOR LOCK INDThis test is able to check door lock indicator (built in door lock and unlock switch on center
console) operation [ON/OFF].
DOOR LOCKThis test is able to check door lock operation [ALL LOCK/ALL UNLOCK/DR UNLOCK/
OTHER UNLOCK].
Test item Description
SECURITY DOOR LOCK SETAnti hijack function mode can be changed in this mode.
 ON: Anti hijack mode is active.
 OFF: Anti hijack mode is inactive.

DLK-52
< FUNCTION DIAGNOSIS >[WITH I-KEY, WITHOUT SUPER LOCK]
DIAGNOSIS SYSTEM (BCM)
CONSULT-III performs the following functions via CAN communication with BCM.
DATA MONITOR
TRUNK
TRUNK : CONSULT-III Function (BCM - TRUNK)INFOID:0000000001396505
APPLICATION ITEM
CONSULT-III performs the following functions via CAN communication with BCM.
DATA MONITOR
ACTIVE TEST
Diagnosis mode Function Description
DATA MONITOR The BCM input/output signals are displayed.
Monitor Item Condition
IGN ON SW Indicates [ON/OFF] condition of ignition switch in ON position.
ACC ON SW Indicates [ON/OFF] condition of ignition switch in ACC position.
KEY ON SW Indicates [ON/OFF] condition of key switch.
PUSH SW Indicates [ON/OFF] condition of ignition knob switch.
I-KEY LOCK Indicates [ON/OFF] condition of lock signal from Intelligent Key.
I-KEY UNLOCK Indicates [ON/OFF] condition of unlock signal from Intelligent Key.
Diagnosis mode Function Description
DATA MONITOR The BCM input/output signals are displayed.
ACTIVE TEST The signals used to activate each device are forcibly supplied from Intelligent Key unit.
Monitor Item Condition
IGN ON SW Indicates [ON/OFF] condition of ignition switch in ON position.
KEY ON SW Indicates [ON/OFF] condition of key switch.
PUSH SW Indicates [ON/OFF] condition of ignition knob switch.
TRNK OPNR SW Indicates [ON/OFF] condition of back door/trunk opener switch.
VEHICLE SPEEDDisplays the vehicle speed signal received from combination meter by numerical value
[km/h].
Test item Description
TRUNK/GLASS HATCH This test is able to check back door actuator/trunk release solenoid operation [ON/OFF].

DLK-54
< FUNCTION DIAGNOSIS >[WITH I-KEY, WITHOUT SUPER LOCK]
DIAGNOSIS SYSTEM (INTELLIGENT KEY UNIT)
ACTIVE TEST
Monitor Item Condition
PUSH SW Indicates [ON (pressed)/OFF (released)] condition of ignition knob switch.
KEY SW Indicates [ON (inserted)/OFF (removed)] condition of key switch.
DR REQ SW Indicates [ON (pressed)/OFF (released)] condition of door request switch (driver side).
AS REQ SW Indicates [ON (pressed)/OFF (released)] condition of door request switch (passenger side).
BD/TR REQ SW Indicates [ON (pressed)/OFF (released)] condition of back door/trunk request switch.
IGN SWIndicates [ON (ON or START position)/OFF (other than ON and START position)] condition of
ignition switch ON position.
ACC SW Indicates [ON/OFF] condition of ignition switch ACC position.
STOP LAMP SW Indicates [ON/OFF] condition of stop lamp switch.
DOOR LOCK SIG Indicates [ON/OFF] condition of LOCK signal from Intelligent Key.
DOOR UNLOCK SIG Indicates [ON/OFF] condition of UNLOCK signal from Intelligent Key.
DOOR SW DRIndicates [OPEN/CLOSE] condition of front door switch (driver side) from BCM via CAN com-
munication.
DOOR SW ASIndicates [OPEN/CLOSE] condition of front door switch (passenger side) from BCM via CAN
communication.
DOOR SW RRIndicates [OPEN/CLOSE] condition of rear door switch (RH) from BCM via CAN communica-
tion.
DOOR SW RLIndicates [OPEN/CLOSE] condition of rear door switch (LH) from BCM via CAN communica-
tion.
DOOR BK SW Indicates [OPEN/CLOSE] condition of back door switch from BCM via CAN communication.
VEHICLE SPEED Displays the vehicle speed signal received from combination meter by numerical value [km/h].
Test item Description
DOOR LOCK/UNLOCKThis test is able to check door lock/unlock operation.
 ALL UNLK: All door lock actuators are unlocked.
 DR UNLK: Door lock actuator (driver side) is unlocked.
 AS UNLK: Door lock actuator (passenger side) is unlocked.
 BK UNLK: This item is indicated, but inactive.
 LOCK: All door lock actuator is locked.
ANTENNAThis test is able to check Intelligent Key antenna operation.
When the following condition are met, hazard warning lamps flash.
 ROOM ANT1: Inside key antenna (console) detects Intelligent Key, when “ROOM
ANT1” is selected.
 ROOM ANT2: Inside key antenna (instrument center/rear seat) detects Intelligent
Key, when “ROOM ANT2”is selected.
 DRIVER ANT: Outside key antenna (driver side) detects Intelligent Key, when “DRIV-
ER ANT” is selected.
 ASSIST ANT: Outside key antenna (passenger side) detects Intelligent Key, when
“ASSIST ANT” is selected.
 BK DOOR ANT: Outside key antenna (rear bumper) detects Intelligent Key, when “BK
DOOR ANT” is selected.
OUTSIDE BUZZERThis test is able to check Intelligent Key warning buzzer(s) operation.
ON
OFF
INSIDE BUZZERThis test is able to check warning chime in combination meter operation.
 TAKE OUT: Take away warning chime sounds.
 KNOB: Ignition knob switch warning chime sounds.
 KEY: Key warning chime sounds.
OFF