front NISSAN TIIDA 2007 Service Repair Manual
[x] Cancel search | Manufacturer: NISSAN, Model Year: 2007, Model line: TIIDA, Model: NISSAN TIIDA 2007Pages: 5883, PDF Size: 78.95 MB
Page 2974 of 5883
![NISSAN TIIDA 2007 Service Repair Manual CYLINDER BLOCK
EM-327
< DISASSEMBLY AND ASSEMBLY >[K9K]
C
D
E
F
G
H
I
J
K
L
MA
EM
N
P O
17. Apply two beads (B) of liquid gasket, with a diameter of 5 mm
(0.20 in).
Use Genuine Liquid Gasket or equi NISSAN TIIDA 2007 Service Repair Manual CYLINDER BLOCK
EM-327
< DISASSEMBLY AND ASSEMBLY >[K9K]
C
D
E
F
G
H
I
J
K
L
MA
EM
N
P O
17. Apply two beads (B) of liquid gasket, with a diameter of 5 mm
(0.20 in).
Use Genuine Liquid Gasket or equi](/img/5/57395/w960_57395-2973.png)
CYLINDER BLOCK
EM-327
< DISASSEMBLY AND ASSEMBLY >[K9K]
C
D
E
F
G
H
I
J
K
L
MA
EM
N
P O
17. Apply two beads (B) of liquid gasket, with a diameter of 5 mm
(0.20 in).
Use Genuine Liquid Gasket or equivalent.
18. Install the oil pan Refer to EM-284, "
Removal and Installation".
19. Crankshaft elastomer seal, timing side.
20. Screw the threaded rod (A) of front oil seal drift set [SST:
KV113B0220 (Mot. 1586)] into the crankshaft.
21. Position the spacer (B) of front oil seal drift set [SST:
KV113B0220 (Mot. 1586)] on the crankshaft.
22. Install the protector complete with the seal onto the spacer, tak-
ing care not to touch the seal.
23. Install the cover (A) and the nut (B) (putting the threaded part
(C) of the nut on the side away from the engine) of front oil seal
drift set [SST: KV113B0220 (Mot. 1586)].
MBIB0484E
MBIB0487E
MBIB0488E
MBIB0489E
MBIB0490E
Page 2975 of 5883
![NISSAN TIIDA 2007 Service Repair Manual EM-328
< DISASSEMBLY AND ASSEMBLY >[K9K]
CYLINDER BLOCK
24. Tighten the nut until the cover touches the spacer.
25. Remove the nut, the cover, the protector and the threaded rod.
26. Crankshaft elasto NISSAN TIIDA 2007 Service Repair Manual EM-328
< DISASSEMBLY AND ASSEMBLY >[K9K]
CYLINDER BLOCK
24. Tighten the nut until the cover touches the spacer.
25. Remove the nut, the cover, the protector and the threaded rod.
26. Crankshaft elasto](/img/5/57395/w960_57395-2974.png)
EM-328
< DISASSEMBLY AND ASSEMBLY >[K9K]
CYLINDER BLOCK
24. Tighten the nut until the cover touches the spacer.
25. Remove the nut, the cover, the protector and the threaded rod.
26. Crankshaft elastomer seal, flywheel side.
27. Install front oil seal drift set [SST: KV113B0210 (Mot. 1585)] on
the crankshaft, securing it with bolts (F).
MBIB0491E
MBIB0492E
MBIB0493E
MBIB0494E
Page 2976 of 5883
![NISSAN TIIDA 2007 Service Repair Manual CYLINDER BLOCK
EM-329
< DISASSEMBLY AND ASSEMBLY >[K9K]
C
D
E
F
G
H
I
J
K
L
MA
EM
N
P O
28. Put the protector complete with the seal on front oil seal drift set
[SST: KV113B0210 (Mot. 1585)], being ca NISSAN TIIDA 2007 Service Repair Manual CYLINDER BLOCK
EM-329
< DISASSEMBLY AND ASSEMBLY >[K9K]
C
D
E
F
G
H
I
J
K
L
MA
EM
N
P O
28. Put the protector complete with the seal on front oil seal drift set
[SST: KV113B0210 (Mot. 1585)], being ca](/img/5/57395/w960_57395-2975.png)
CYLINDER BLOCK
EM-329
< DISASSEMBLY AND ASSEMBLY >[K9K]
C
D
E
F
G
H
I
J
K
L
MA
EM
N
P O
28. Put the protector complete with the seal on front oil seal drift set
[SST: KV113B0210 (Mot. 1585)], being careful not to touch the
seal.
29. Install the cover (G) and nut (H) (putting the threaded part (I) of
the nut on the side away from the engine) of front oil seal drift
set [SST: KV113B0210 (Mot. 1585)].
30. Tighten the nut until the cover touches the cylinder block.
MBIB0495E
MBIB0496E
MBIB0497E
MBIB0498E
Page 2991 of 5883
![NISSAN TIIDA 2007 Service Repair Manual EXHAUST SYSTEM
EX-5
< ON-VEHICLE REPAIR >[HR16DE]
C
D
E
F
G
H
I
J
K
L
MA
EX
N
P O
ON-VEHICLE REPAIR
EXHAUST SYSTEM
ComponentINFOID:0000000001337859
Removal and InstallationINFOID:0000000001337860
REMO NISSAN TIIDA 2007 Service Repair Manual EXHAUST SYSTEM
EX-5
< ON-VEHICLE REPAIR >[HR16DE]
C
D
E
F
G
H
I
J
K
L
MA
EX
N
P O
ON-VEHICLE REPAIR
EXHAUST SYSTEM
ComponentINFOID:0000000001337859
Removal and InstallationINFOID:0000000001337860
REMO](/img/5/57395/w960_57395-2990.png)
EXHAUST SYSTEM
EX-5
< ON-VEHICLE REPAIR >[HR16DE]
C
D
E
F
G
H
I
J
K
L
MA
EX
N
P O
ON-VEHICLE REPAIR
EXHAUST SYSTEM
ComponentINFOID:0000000001337859
Removal and InstallationINFOID:0000000001337860
REMOVAL
CAUTION:
Be sure to use genuine NISSAN exhaust system parts or equivalents which are specially designed
for heat resistance, corrosion resistance and shape.
Perform the operation with the exhaust system fully cooled down because the system will be hot
just after the engine stops.
Be careful not to cut your hand on heat insulator edge.
1. Disconnect harness connector of heated oxygen sensor 2.
Using Tool, remove heated oxygen sensor 2.
CAUTION:
Be careful not to damage heated oxygen sensor 2.
a.
1. Main muffler 2. Mounting rubber 3. Ring gasket
4. Center muffler 5. Mounting rubber 6. Spring
7. Seal bearing 8. Heated oxygen sensor 2 9. Exhaust front tube
10. Seal bearing 11. Stud bolt 12. Spring
13. Ground cable
WBIA0844E
Tool number : KV10114400 (J-38365)
Page 2992 of 5883
![NISSAN TIIDA 2007 Service Repair Manual EX-6
< ON-VEHICLE REPAIR >[HR16DE]
EXHAUST SYSTEM
2. Disconnect each joint and mounting rubber.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
Always replace exhaust gaskets NISSAN TIIDA 2007 Service Repair Manual EX-6
< ON-VEHICLE REPAIR >[HR16DE]
EXHAUST SYSTEM
2. Disconnect each joint and mounting rubber.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
Always replace exhaust gaskets](/img/5/57395/w960_57395-2991.png)
EX-6
< ON-VEHICLE REPAIR >[HR16DE]
EXHAUST SYSTEM
2. Disconnect each joint and mounting rubber.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
Always replace exhaust gaskets and seal bearings with new ones when installing.
Discard any heated oxygen sensor 2 which has been dropped from a height of more than 0.5 m (19.7
in) onto a hard surface such as a concrete floor; use a new one.
Before installing a new heated oxygen sensor 2, clean exhaust system threads using the heated oxy-
gen sensor thread cleaner and apply anti-seize lubricant (commercial service tool).
Do not over tighten heated oxygen sensor 2. Doing so may cause damage to the heated oxygen sen-
sor 2, resulting in the “MIL” coming on.
Remove deposits from the sealing surface of each connection. Connect them securely to avoid
exhaust leakage.
Temporarily tighten nuts on the exhaust manifold side and bolts on the vehicle side. Check each part
for unusual interference, and then tighten them to the specified torque.
When installing each mounting rubber, avoid twisting or unusual extension in up/down and right/left
directions.
Exhaust Manifold to Exhaust Front Tube
1. Securely insert seal bearing (2) into exhaust manifold (1) side in
the direction shown.
Exhaust front tube (5)
CAUTION:
Be careful not to damage seal bearing surface when install-
ing.
2. Install spring (3), tighten nut (4).
Be careful that the stud bolt nut does not interfere with the
flanged area ( ).
Make sure the spring (3) sits properly on the flange surface by
aligning it to the locator dimples.
Exhaust Front Tube to Center Muffler
1. Securely insert seal bearing (2) into exhaust front tube (1) side
in the direction shown.
Center muffler (5)
CAUTION:
Be careful not to damage seal bearing surface when install-
ing.
2. With spring (3), tighten bolt (4).
Be careful that the stud bolt does not interfere with the flanged
area ( ).
Make sure the spring (3) sits properly on the flange surface by
aligning it to the locator dimples.
InspectionINFOID:0000000001700348
INSPECTION AFTER INSTALLATION
With the engine running, check exhaust tube joints for exhaust leakage and unusual noise.
Check to ensure that brackets and mounting rubbers are installed properly and free from undue stress.
Improper installation could result in excessive noise and vibration.
PBIC3797E
PBIC3798E
Page 2996 of 5883
![NISSAN TIIDA 2007 Service Repair Manual EX-10
< ON-VEHICLE REPAIR >[MR18DE]
EXHAUST SYSTEM
ON-VEHICLE REPAIR
EXHAUST SYSTEM
ComponentINFOID:0000000001696508
Removal and InstallationINFOID:0000000001696507
REMOVAL
CAUTION:
Be sure to use g NISSAN TIIDA 2007 Service Repair Manual EX-10
< ON-VEHICLE REPAIR >[MR18DE]
EXHAUST SYSTEM
ON-VEHICLE REPAIR
EXHAUST SYSTEM
ComponentINFOID:0000000001696508
Removal and InstallationINFOID:0000000001696507
REMOVAL
CAUTION:
Be sure to use g](/img/5/57395/w960_57395-2995.png)
EX-10
< ON-VEHICLE REPAIR >[MR18DE]
EXHAUST SYSTEM
ON-VEHICLE REPAIR
EXHAUST SYSTEM
ComponentINFOID:0000000001696508
Removal and InstallationINFOID:0000000001696507
REMOVAL
CAUTION:
Be sure to use genuine NISSAN exhaust system parts or equivalents which are specially designed
for heat resistance, corrosion resistance and shape.
Perform the operation with the exhaust system fully cooled down because the system will be hot
just after the engine stops.
Be careful not to cut your hand on heat insulator edge.
1. Disconnect harness connector of heated oxygen sensor 2.
Using Tool, remove heated oxygen sensor 2.
CAUTION:
Be careful not to damage heated oxygen sensor 2.
a.
1. Main muffler 2. Mounting rubber 3. Ring gasket
4. Center muffler 5. Mounting rubber 6. Spring
7. Seal bearing 8. Heated oxygen sensor 2 9. Exhaust front tube
10. Seal bearing 11. Stud bolt 12. Spring
13. Ground cable
WBIA0844E
Tool number : KV10114400 (J-38365)
Page 2997 of 5883
![NISSAN TIIDA 2007 Service Repair Manual EXHAUST SYSTEM
EX-11
< ON-VEHICLE REPAIR >[MR18DE]
C
D
E
F
G
H
I
J
K
L
MA
EX
N
P O
2. Disconnect each joint and mounting rubber.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION: NISSAN TIIDA 2007 Service Repair Manual EXHAUST SYSTEM
EX-11
< ON-VEHICLE REPAIR >[MR18DE]
C
D
E
F
G
H
I
J
K
L
MA
EX
N
P O
2. Disconnect each joint and mounting rubber.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:](/img/5/57395/w960_57395-2996.png)
EXHAUST SYSTEM
EX-11
< ON-VEHICLE REPAIR >[MR18DE]
C
D
E
F
G
H
I
J
K
L
MA
EX
N
P O
2. Disconnect each joint and mounting rubber.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
Always replace exhaust gaskets and seal bearings with new ones when installing.
Discard any heated oxygen sensor 2 which has been dropped from a height of more than 0.5 m (19.7
in) onto a hard surface such as a concrete floor; use a new one.
Before installing a new heated oxygen sensor 2, clean exhaust system threads using the heated oxy-
gen sensor thread cleaner and apply anti-seize lubricant (commercial service tool).
Do not over tighten heated oxygen sensor 2. Doing so may cause damage to the heated oxygen sen-
sor 2, resulting in the “MIL” coming on.
Remove deposits from the sealing surface of each connection. Connect them securely to avoid
exhaust leakage.
Temporarily tighten nuts on the exhaust manifold side and bolts on the vehicle side. Check each part
for unusual interference, and then tighten them to the specified torque.
When installing each mounting rubber, avoid twisting or unusual extension in up/down and right/left
directions.
Exhaust Manifold to Exhaust Front Tube
1. Securely insert seal bearing (2) into exhaust manifold (1) side in
the direction shown.
Exhaust front tube (5)
CAUTION:
Be careful not to damage seal bearing surface when install-
ing.
2. Install spring (3), tighten nut (4).
Be careful that the stud bolt nut does not interfere with the
flanged area ( ).
Make sure the spring (3) sits properly on the flange surface by
aligning it to the locator dimples.
Exhaust Front Tube to Center Muffler
1. Securely insert seal bearing (2) into exhaust front tube (1) side
in the direction shown.
Center muffler (5)
CAUTION:
Be careful not to damage seal bearing surface when install-
ing.
2. With spring (3), tighten bolt (4).
Be careful that the stud bolt does not interfere with the flanged
area ( ).
Make sure the spring (3) sits properly on the flange surface by
aligning it to the locator dimples.
INSPECTION AFTER INSTALLATION
With the engine running, check exhaust tube joints for exhaust leakage and unusual noise.
Check to ensure that brackets and mounting rubbers are installed properly and free from undue stress.
Improper installation could result in excessive noise and vibration.
InspectionINFOID:0000000001696389
INSPECTION AFTER INSTALLATION
Make sure clearance between tail tube and rear bumper is even.
With engine running, check exhaust tube joints for gas leakage and unusual noises.
Check to ensure that mounting brackets and mounting rubbers are installed properly and free from undue
stress. Improper installation could result in excessive noise and vibration.
PBIC3797E
PBIC3798E
Page 3000 of 5883
![NISSAN TIIDA 2007 Service Repair Manual EX-14
< ON-VEHICLE REPAIR >[K9K]
EXHAUST SYSTEM
ON-VEHICLE REPAIR
EXHAUST SYSTEM
ComponentINFOID:0000000001700347
Removal and InstallationINFOID:0000000001696393
CAUTION:
Be sure to use genuine exha NISSAN TIIDA 2007 Service Repair Manual EX-14
< ON-VEHICLE REPAIR >[K9K]
EXHAUST SYSTEM
ON-VEHICLE REPAIR
EXHAUST SYSTEM
ComponentINFOID:0000000001700347
Removal and InstallationINFOID:0000000001696393
CAUTION:
Be sure to use genuine exha](/img/5/57395/w960_57395-2999.png)
EX-14
< ON-VEHICLE REPAIR >[K9K]
EXHAUST SYSTEM
ON-VEHICLE REPAIR
EXHAUST SYSTEM
ComponentINFOID:0000000001700347
Removal and InstallationINFOID:0000000001696393
CAUTION:
Be sure to use genuine exhaust system parts or equivalents which are specially designed for heat
resistance, corrosion resistance and shape.
Perform the operation with the exhaust system fully cooled down because the system is still hot just
after the engine stops.
Be careful not to cut your hand on the insulator edge.
REMOVAL
Disconnect each joint and mounting.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
Always replace exhaust gaskets and seal bearings with new ones when installing.
Remove deposits from the sealing surface of each connection. Connect them securely to avoid
exhaust leakage.
Temporarily tighten nuts on the exhaust manifold side and bolts on the vehicle side. Check each part
for unusual interference, and then tighten them to the specified torque.
1. Main muffler 2. Mounting rubber 3. Ring gasket
4. Center muffler 5. Spring 6. Seal bearing
7. Exhaust front tube 8. Stud bolt 9. Ground cable
AWBIA0159GB
Page 3001 of 5883
![NISSAN TIIDA 2007 Service Repair Manual EXHAUST SYSTEM
EX-15
< ON-VEHICLE REPAIR >[K9K]
C
D
E
F
G
H
I
J
K
L
MA
EX
N
P O
When installing each mounting rubbers, avoid twisting or unusual extension in up/down and right/
left directions.
Exha NISSAN TIIDA 2007 Service Repair Manual EXHAUST SYSTEM
EX-15
< ON-VEHICLE REPAIR >[K9K]
C
D
E
F
G
H
I
J
K
L
MA
EX
N
P O
When installing each mounting rubbers, avoid twisting or unusual extension in up/down and right/
left directions.
Exha](/img/5/57395/w960_57395-3000.png)
EXHAUST SYSTEM
EX-15
< ON-VEHICLE REPAIR >[K9K]
C
D
E
F
G
H
I
J
K
L
MA
EX
N
P O
When installing each mounting rubbers, avoid twisting or unusual extension in up/down and right/
left directions.
Exhaust Manifold to Exhaust Front Tube
1. Securely insert seal bearing (2) into catalyst (1) side in the direc-
tion shown.
Exhaust front tube (5)
CAUTION:
Be careful not to damage seal bearing surface when install-
ing.
2. Install spring (3), tighten nut (4).
Be careful that the stud bolt nut does not interfere with the
flanged area ( ).
Make sure the spring (3) sits properly on the flange surface by
aligning it to the locator dimples.
Exhaust Front Tube to Center Muffler
1. Securely insert seal bearing (2) into exhaust front tube (1) side
in the direction shown.
Center muffler (5)
CAUTION:
Be careful not to damage seal bearing surface when install-
ing.
2. With spring (3), tighten bolt (4).
Be careful that the stud bolt does not interfere with the flanged
area ( ).
Make sure the spring (3) sits properly on the flange surface by
aligning it to the locator dimples.
INSPECTION AFTER INSTALLATION
With the engine running, check exhaust tube joints for exhaust leakage and unusual noise.
Check to ensure that brackets and mounting rubbers are installed properly and free from undue stress.
Improper installation could result in excessive noise and vibration.
InspectionINFOID:0000000001696394
INSPECTION AFTER INSTALLATION
With the engine running, check exhaust tube joints for gas leakage and unusual noises.
Check to ensure that mounting brackets and mounting rubbers are installed properly and free from undue
stress. Improper installation could result in excessive noise and vibration.
PBIC3797E
PBIC3798E
Page 3002 of 5883

EXL-1
DRIVER CONTROLS
C
D
E
F
G
H
I
J
K
M
SECTION EXL
A
B
EXL
N
O
P
CONTENTS
EXTERIOR LIGHTING SYSTEM
BASIC INSPECTION ....................................5
DIAGNOSIS AND REPAIR WORKFLOW ..........5
Work Flow .................................................................5
FUNCTION DIAGNOSIS ...............................8
HEADLAMP (HALOGEN) ...................................8
System Diagram ........................................................8
System Description ...................................................8
Component Parts Location ........................................8
Component Description .............................................8
HEADLAMP (XENON) .......................................10
System Diagram ......................................................10
System Description .................................................10
Component Parts Location ......................................10
Component Description ..........................................11
AUTO LIGHT SYSTEM ......................................12
System Diagram ......................................................12
System Description .................................................12
Component Parts Location ......................................12
Component Description ...........................................13
HEADLAMP AIMING SYSTEM (MANUAL) .......14
System Diagram ......................................................14
System Description .................................................14
Component Parts Location ......................................14
Component Description ...........................................14
HEADLAMP AIMING SYSTEM (AUTOMAT-
IC) .......................................................................
15
System Diagram ......................................................15
System Description .................................................15
Component Parts Location ......................................15
Component Description ...........................................15
DAYTIME LIGHT SYSTEM ................................17
System Diagram ......................................................17
System Description .................................................17
Component Parts Location ......................................17
Component Description ..........................................18
FRONT FOG LAMP ..........................................19
System Diagram ......................................................19
System Description ..................................................19
Component Parts Location ......................................19
Component Description ...........................................20
REAR FOG LAMP .............................................21
System Diagram ......................................................21
System Description ..................................................21
Component Parts Location ......................................21
Component Description ..........................................21
TURN SIGNAL AND HAZARD WARNING
LAMPS ..............................................................
22
System Diagram ......................................................22
System Description ..................................................22
Component Parts Location ......................................22
Component Description ...........................................23
PARKING, LICENSE PLATE AND TAIL
LAMPS ..............................................................
24
System Diagram ......................................................24
System Description ..................................................24
Component Parts Location ......................................25
Component Description ...........................................25
DIAGNOSIS SYSTEM (BCM) ...........................26
COMMON ITEM .........................................................26
COMMON ITEM : CONSULT-III Function (BCM -
COMMON ITEM) .....................................................
26
BCM ...........................................................................26
BCM : CONSULT-III Function (BCM - BCM) ...........26
HEADLAMP ...............................................................26
HEADLAMP : CONSULT-III Function (BCM -
HEAD LAMP) ...........................................................
26
FLASHER ...................................................................27