page 71 NISSAN TIIDA 2008 Service Service Manual
[x] Cancel search | Manufacturer: NISSAN, Model Year: 2008, Model line: TIIDA, Model: NISSAN TIIDA 2008Pages: 2771, PDF Size: 60.61 MB
Page 889 of 2771
CVT-50
< SERVICE INFORMATION >
TROUBLE DIAGNOSIS
Engine Brake Adjustment
CAUTION:
Mode of “+1”“0”“-1”“-2”“OFF” can be selected by pressing the “UP”“DOWN” on CONSULT-III screen.
However, do not select mode other than “0” and “OFF”. If the “+1” or “-1” or “-2” is selected, that
might cause the irregular driveability.
Check CVT Fluid Deterioration Date
CAUTION:
Touch “CLEAR” after changing CVT fluid, and then erase “CVTF DETERIORATION DATE”.
SELF-DIAGNOSTIC RESULT MODE
After performing self-diagnosis, place check marks for results on the CVT-30, "How to Perform Trouble Diag-
nosis for Quick and Accurate Repair" . Reference pages are provided following the items.
Display Items List
X: Applicable —: Not applicable
Item name Description
ENGINE BRAKE ADJ. The engine brake level setting can be canceled.
CONFORM CVTF DETERIORTN The CVT fluid deterioration level can be checked.
“ENGINE BRAKE LEVEL”
0: Initial set value (Engine brake level control is ac-
tivated)
OFF: Engine brake level control is deactivated.
“CVTF DETERIORATION DATE”
More than 210000:
It is necessary to change CVT fluid.
Less than 210000:
It is not necessary to change CVT fluid.
Items (CONSULT-
III screen terms)Malfunction is detected when...TCM self-di-
agnosisOBD-III (DTC)
Reference
page “TRANSMIS-
SION” with
CONSULT-IIIMIL indicator
lamp*1, “EN-
GINE” with
CONSULT-III
or GST
CAN COMM CIR-
CUITWhen TCM is not transmitting or receiving CAN communica-
tion signal for 2 seconds or moreU1000 U1000CVT-56
CONTROL
UNIT(CAN)When detecting error during the initial diagnosis of CAN con-
troller of TCMU1010 U1010CVT-59
STARTER RELAY/
CIRCIf this signal is ON other than in “P” or “N” position, this is
judged to be a malfunction
(And if it is OFF in “P” or “N” position, this is judged to be a
malfunction too)P0615 —CVT-60
BRAKE SW/CIRC When the brake switch does not switch to ON or OFF P0703 —CVT-63
PNP SW/CIRC• PNP switch 1-4 signals input with impossible pattern
• PNP switch 3 monitor terminal open or short circuitP0705 P0705CVT-65
ATF TEMP SEN/
CIRCDuring running, the CVT fluid temperature sensor signal volt-
age is excessively high or lowP0710 P0710CVT-71
INPUT SPD SEN/
CIRC• Input speed sensor (primary speed sensor) signal is not in-
put due to an open circuit
• An unexpected signal is input when vehicle is being drivenP0715 P0715CVT-76
Page 890 of 2771
![NISSAN TIIDA 2008 Service Service Manual TROUBLE DIAGNOSIS
CVT-51
< SERVICE INFORMATION >
D
E
F
G
H
I
J
K
L
MA
B
CVT
N
O
PVEH SPD SEN/
CIR AT• Signal from vehicle speed sensor CVT [Output speed sen-
sor (Secondary speed sensor)] not input](/img/5/57399/w960_57399-889.png "NISSAN TIIDA 2008 Service Service Manual TROUBLE DIAGNOSIS
CVT-51
< SERVICE INFORMATION >
D
E
F
G
H
I
J
K
L
MA
B
CVT
N
O
PVEH SPD SEN/
CIR AT• Signal from vehicle speed sensor CVT [Output speed sen-
sor (Secondary speed sensor)] not input")
TROUBLE DIAGNOSIS
CVT-51
< SERVICE INFORMATION >
D
E
F
G
H
I
J
K
L
MA
B
CVT
N
O
PVEH SPD SEN/
CIR AT• Signal from vehicle speed sensor CVT [Output speed sen-
sor (Secondary speed sensor)] not input due to open or
short circuit
• Unexpected signal input during runningP0720 P0720CVT-80
ENGINE SPEED
SIG• TCM does not receive the CAN communication signal from
the ECM
• Engine speed is too low while drivingP0725 —CVT-85
BELT DAMG Unexpected gear ratio detected P0730 —CVT-87
TCC SOLENOID/
CIRCNormal voltage not applied to solenoid due to open or short
circuitP0740 P0740CVT-88
A/T TCC S/V
FNCTN• CVT cannot perform lock-up even if electrical circuit is good
• TCM detects as irregular by comparing difference value
with slip rotation
• There is big difference engine speed and primary speed
when TCM lock-up signal is onP0744 P0744CVT-93
L/PRESS SOL/
CIRC• Normal voltage not applied to solenoid due to open or short
circuit
• TCM detects as irregular by comparing target value with
monitor valueP0745 P0745CVT-95
PRS CNT SOL/A
FCTNUnexpected gear ratio was detected in the LOW side due to
excessively low line pressureP0746 P0746CVT-100
PRS CNT SOL/B
FCTNSecondary pressure is too high or too low compared with the
commanded value while drivingP0776 P0776CVT-102
PRS CNT SOL/B
CIRC• Normal voltage not applied to solenoid due to cut line,
short, or the like
• TCM detects as irregular by comparing target value with
monitor valueP0778 P0778CVT-104
TR PRS SENS/A
CIRCSignal voltage of the transmission fluid pressure sensor A
(secondary pressure sensor) is too high or too low while driv-
ingP0840 P0840CVT-109
PRESS SEN/
FNCTNCorrelation between the values of the transmission fluid pres-
sure sensor A (secondary pressure sensor) and the transmis-
sion fluid pressure sensor B (primary pressure sensor) is out
of specificationP0841 —CVT-113
TR PRS SENS/B
CIRCSignal voltage of the transmission fluid pressure sensor B
(primary pressure sensor) is too high or too low while drivingP0845 P0845CVT-115
SEC/PRESS
DOWNSecondary fluid pressure is too low compared with the com-
manded value while drivingP0868 —CVT-119
TCM-POWER
SUPPLY• When the power supply to the TCM is cut OFF, for example
because the battery is removed, and the self-diagnosis
memory function stops
• This is not a malfunction message (Whenever shutting
OFF a power supply to the TCM, this message appears on
the screen)P1701 —CVT-121
TP SEN/CIRC A/TTCM does not receive the proper accelerator pedal position
signals (input by CAN communication) from ECMP1705 —CVT-125
ESTM VEH SPD
SIG*2• CAN communication with the ABS actuator and the electric
unit (control unit) is malfunctioning
• There is a great difference between the vehicle speed sig-
nal from the ABS actuator and the electric unit (control
unit), and the vehicle speed sensor signalP1722 —CVT-127
Items (CONSULT-
III screen terms)Malfunction is detected when...TCM self-di-
agnosisOBD-III (DTC)
Reference
page “TRANSMIS-
SION” with
CONSULT-IIIMIL indicator
lamp*1, “EN-
GINE” with
CONSULT-III
or GST
Page 891 of 2771
CVT-52
< SERVICE INFORMATION >
TROUBLE DIAGNOSIS
*1: Refer to CVT-27, "Malfunction Indicator Lamp (MIL)" .
*2: Models without ABS does not indicate.
DATA MONITOR MODE
Display Items List
X: Standard, —: Not applicable, : Option
CVT SPD SEN/
FNCTNA rotation sensor error is detected because the gear does not
change in accordance with the position of the stepping motor
CAUTION:
One of the “P0720 VEH SPD SEN/CIR AT”, the “P0715 IN-
PUT SPD SEN/CIRC” or the “P0725 ENGINE SPEED SIG“
is displayed with the DTC at the same timeP1723 —CVT-129
ELEC TH CON-
TROLThe electronically controlled throttle for ECM is malfunction-
ingP1726 —CVT-131
LU-SLCT SOL/
CIRC• Normal voltage not applied to solenoid due to cut line,
short, or the like
• TCM detects as irregular by comparing target value with
monitor valueP1740 P1740CVT-132
L/PRESS CON-
TROLTCM detects the unexpected line pressure P1745 —CVT-136
STEP MOTR CIRCEach coil of the step motor is not energized properly due to
an open or a shortP1777 P1777CVT-137
STEP MOTR/FNCThere is a great difference between the number of steps for
the stepping motor and for the actual gear ratioP1778 P1778CVT-141
NO DTC IS DE-
TECTED: FUR-
THER TESTING
MAY BE RE-
QUIREDNo NG item has been detected X X — Items (CONSULT-
III screen terms)Malfunction is detected when...TCM self-di-
agnosisOBD-III (DTC)
Reference
page “TRANSMIS-
SION” with
CONSULT-IIIMIL indicator
lamp*1, “EN-
GINE” with
CONSULT-III
or GST
Monitored item (Unit)Monitor item selection
Remarks ECU IN-
PUT SIG-
NALSMAIN SIG-
NALSSELEC-
TION
FROM
MENU
VSP SENSOR (km/h) X — Output speed sensor (secondary speed sensor).
ESTM VSP SIG (km/h) X — Models without ABS does not indicate.
PRI SPEED SEN (rpm) X —
ENG SPEED SIG (rpm) X —
SEC HYDR SEN (V) X —
PRI HYDR SEN (V) X —
ATF TEMP SEN (V) X — CVT fluid temperature sensor
VIGN SEN (V) X —
VEHICLE SPEED (km/h) — X Vehicle speed recognized by the TCM.
PRI SPEED (rpm) — X Primary pulley speed.
SEC SPEED (rpm) — — Secondary pulley speed.
Page 1034 of 2771
COMBINATION METERS
DI-13
< SERVICE INFORMATION >
C
D
E
F
G
H
I
J
L
MA
B
DI
N
O
P
CONSULT-III Function (METER/M&A)INFOID:0000000001704498
CONSULT-III can display each diagnostic item using the diagnostic test modes shown following.
SELF-DIAGNOSTIC RESULTS
Display Item List
NOTE:
“TIME” indicates the following.
• 0: Indicates that a malfunction is detected at present.
• 1-63: Indicates that a malfunction was dectected in the past. (Displays number of ignition switch OFF → ON
cycles after malfunction is detected. Self-diagnostic result is erased when “63” is exceded.)
DATA MONITOR
Display Item List
METER diagnosis mode Description
SELF-DIAG RESULTS Displays combination meter self-diagnosis results.
DATA MONITOR Displays combination meter input/output data in real time.
CAN DIAG SUPPORT MNTR The result of transmit/receive diagnosis of CAN communication can be read.
CONSULT-III display Malfunction Reference page
CAN COMM CIRC [U1000]Malfunction is detected in CAN communication lines.
CAUTION:
Even when there is no malfunction on CAN communication system, mal-
function may be misinterpreted when battery has low voltage (when main-
taining 7 - 8 V for about 2 seconds) or 10A fuse [No. 14, located in the fuse
block (J/B)] is removed.DI-19
VEHICLE SPEED CIRC [B2205]Malfunction is detected when an erroneous speed signal is input.
CAUTION:
Even when there is no malfunction on speed signal system, malfunctions
may be misinterpreted when battery has low voltage (when maintaining 7
- 8 V for about 2 seconds).DI-16
Display item [Unit]MAIN
SIGNALSSELECTION
FROM MENUContents
SPEED METER [km/h] X XThe value of vehicle speed signal, which is input from ABS ac-
tuator and electric unit (control unit).
SPEED OUTPUT [km/h] X XThe value of vehicle speed signal, which is transmitted to each
unit with CAN communication.
TACHO METER [rpm] X X The value of engine speed signal, which is input from ECM.
W TEMP METER [°C] X XThe value of engine coolant temperature signal, which is input
from ECM.
FUEL METER [lit.] X XThe value, which processes a resistance signal from fuel
gauge.
DISTANCE [km] X XThe value, which is calculated by vehicle speed signal from
ABS actuator and electric unit (control unit), fuel gauge and fuel
consumption signal from ECM.
FUEL W/L [ON/OFF] X X Indicates [ON/OFF] condition of low-fuel warning lamp.
C-ENG W/L [ON/OFF] XIndicates [ON/OFF] condition of malfunction indicator lamp
(MIL).
AIR PRES W/L X Indicates [ON/OFF] condition of low tire pressure warning lamp.
SEAT BELT W/L X Indicates [ON/OFF] condition of seat belt warning lamp.
BUZZER [ON/OFF] X X Indicates [ON/OFF] condition of buzzer.
DOOR W/L [ON/OFF] X Indicates [ON/OFF] condition of door warning lamp.
HI-BEAM IND [ON/OFF] X Indicates [ON/OFF] condition of high beam indicator lamp.
Page 1083 of 2771
INDEX FOR DTC
EC-9
< SERVICE INFORMATION >
C
D
E
F
G
H
I
J
K
L
MA
EC
N
P O
SERVICE INFORMATION
INDEX FOR DTC
DTC No. IndexINFOID:0000000001702546
NOTE:
•If DTC U1000 or U1001 is displayed with other DTC, first perform the trouble diagnosis for DTC
U1000, U1001. Refer to EC-143
.
•If DTC U1010 is displayed with other DTC, first perform the trouble diagnosis for DTC U1010.
Refer to EC-145
.
DTC*1
Items
(CONSULT-II screen terms)Reference page
CONSULT-II
GST*
2ECM*3
U1000
1000*4CAN COMM CIRCUITEC-143
U1001
1001*4CAN COMM CIRCUITEC-143
U1010 1010 CONTROL UNIT(CAN)EC-145
P0000 0000NO DTC IS DETECTED.
FURTHER TESTING
MAY BE REQUIRED.—
P0011 0011 INT/V TIM CONT-B1EC-147
P0031 0031 A/F SEN1 HTR (B1)EC-151
P0032 0032 A/F SEN1 HTR (B1)EC-151
P0037 0037 HO2S2 HTR (B1)EC-156
P0038 0038 HO2S2 HTR (B1)EC-156
P0075 0075 INT/V TIM V/CIR-B1EC-162
P0101 0101 MAF SEN/CIRCUITEC-167
P0102 0102 MAF SEN/CIRCUITEC-175
P0103 0103 MAF SEN/CIRCUITEC-175
P0112 0112 IAT SEN/CIRCUITEC-182
P0113 0113 IAT SEN/CIRCUITEC-182
P0117 0117 ECT SEN/CIRCEC-187
P0118 0118 ECT SEN/CIRCEC-187
P0122 0122 TP SEN 2/CIRCEC-192
P0123 0123 TP SEN 2/CIRCEC-192
P0125 0125 ECT SENSOREC-198
P0127 0127 IAT SENSOREC-201
P0128 0128 THERMSTAT FNCTNEC-204
P0130 0130 A/F SENSOR1 (B1)EC-206
P0131 0131 A/F SENSOR1 (B1)EC-213
P0132 0132 A/F SENSOR1 (B1)EC-219
P0133 0133 A/F SENSOR1 (B1)EC-225
P0137 0137 HO2S2 (B1)EC-233
P0138 0138 HO2S2 (B1)EC-240
P0139 0139 HO2S2 (B1)EC-250
P0171 0171 FUEL SYS-LEAN-B1EC-257
P0172 0172 FUEL SYS-RICH-B1EC-264
P0181 0181 FTT SENSOREC-270
Page 1084 of 2771
EC-10
< SERVICE INFORMATION >
INDEX FOR DTC
P0182 0182 FTT SEN/CIRCUITEC-274
P0183 0183 FTT SEN/CIRCUITEC-274
P0222 0222 TP SEN 1/CIRCEC-278
P0223 0223 TP SEN 1/CIRCEC-278
P0300 0300 MULTI CYL MISFIREEC-284
P0301 0301 CYL 1 MISFIREEC-284
P0302 0302 CYL 2 MISFIREEC-284
P0303 0303 CYL 3 MISFIREEC-284
P0304 0304 CYL 4 MISFIREEC-284
P0327 0327 KNOCK SEN/CIRC-B1EC-291
P0328 0328 KNOCK SEN/CIRC-B1EC-291
P0335 0335 CKP SEN/CIRCUITEC-295
P0340 0340 CMP SEN/CIRC-B1EC-302
P0420 0420 TW CATALYST SYS-B1EC-308
P0441 0441 EVAP PURG FLOW/MONEC-313
P0442 0442 EVAP SMALL LEAKEC-318
P0443 0443 PURG VOLUME CONT/VEC-325
P0444 0444 PURG VOLUME CONT/VEC-332
P0445 0445 PURG VOLUME CONT/VEC-332
P0447 0447 VENT CONTROL VALVEEC-338
P0448 0448 VENT CONTROL VALVEEC-345
P0451 0451 EVAP SYS PRES SENEC-351
P0452 0452 EVAP SYS PRES SENEC-355
P0453 0453 EVAP SYS PRES SENEC-362
P0455 0455 EVAP GROSS LEAKEC-370
P0456 0456 EVAP VERY SML LEAKEC-377
P0460 0460 FUEL LEV SEN SLOSHEC-385
P0461 0461 FUEL LEVEL SENSOREC-387
P0462 0462 FUEL LEVL SEN/CIRCEC-389
P0463 0463 FUEL LEVL SEN/CIRCEC-389
P0500 0500
VEH SPEED SEN/CIRC*5EC-391
P0506 0506 ISC SYSTEMEC-393
P0507 0507 ISC SYSTEMEC-395
P0605 0605 ECMEC-397
P0643 0643 SENSOR POWER/CIRCEC-400
P0705 0705 PNP SW/CIRCAT- 8 6 (A/T),
CVT-65
(CVT)
P0710 0710 ATF TEMP SEN/CIRCAT- 9 1
(A/T),
CVT-71
(CVT)
P0715 0715 INPUT SPD SEN/CIRCCVT-76
P0720 0720
VEH SPD SEN/CIR AT*5AT- 9 6 (A/T),
CVT-80
(CVT)
P0725 0725 ENGINE SPEED SIGAT- 1 0 1
DTC*1
Items
(CONSULT-II screen terms)Reference page
CONSULT-II
GST*
2ECM*3
Page 1085 of 2771
INDEX FOR DTC
EC-11
< SERVICE INFORMATION >
C
D
E
F
G
H
I
J
K
L
MA
EC
N
P OP0731 0731 A/T 1ST GR FNCTNAT- 1 0 5
P0732 0732 A/T 2ND GR FNCTNAT- 1 0 8
P0733 0733 A/T 3RD GR FNCTNAT- 111
P0734 0734 A/T 4TH GR FNCTNAT- 11 4
P0740 0740 TCC SOLENOID/CIRCAT- 11 9
P0744 0744 A/T TCC S/V FNCTNAT- 1 2 4 (A/T),
CVT-93
(CVT)
P0745 0745 L/PRESS SOL/CIRCAT- 1 2 9
P0746 0746 PRS CNT SOL/A FCTNCVT-100
P0750 0750 SFT SOL A/CIRCAT- 1 3 4
P0755 0755 SFT SOL B/CIRCAT- 1 3 9
P0776 0776 PRS CNT SOL/B FCTNCVT-102
P0778 0778 PRS CNT SOL/B CIRCCVT-104
P0840 0840 TR PRS SENS/A CIRCCVT-109
P0845 0845 TR PRS SENS/B CIRCCVT-115
P0850 0850 P-N POS SW/CIRCUITEC-405
P1148 1148 CLOSED LOOP-B1EC-411
P1217 1217 ENG OVER TEMPEC-412
P1225 1225 CTP LEARNINGEC-426
P1226 1226 CTP LEARNINGEC-428
P1421 1421 COLD START CONTROLEC-430
P1564 1564 ASCD SWEC-432
P1572 1572 ASCD BRAKE SWEC-438
P1574 1574 ASCD VHL SPD SENEC-447
P1610 - P1615 1610 - 1615 NATS MALFUNCTIONBL-210
P1705 1705 TP SEN/CIRC CVTCVT-125
P1715 1715 IN PULY SPEEDEC-449 (A/T),
EC-450
(CVT)
P1740 1740 LU-SLCT SOL/CIRCCVT-132
P1760 1760 O/R CLTCH SOL/CIRCAT- 1 4 4
P1777 1777 STEP MOTR CIRCCVT-137
P1778 1778 STEP MOTR FNCCVT-141
P1805 1805 BRAKE SW/CIRCUITEC-452
P2100 2100 ETC MOT PWREC-456
P2101 2101 ETC FUNCTION/CIRCEC-461
P2103 2103 ETC MOT PWREC-456
P 2 11 8 2 11 8 E T C M O TEC-467
P 2 11 9 2 11 9 E T C A C T REC-472
P2122 2122 APP SEN 1/CIRCEC-474
P2123 2123 APP SEN 1/CIRCEC-474
P2127 2127 APP SEN 2/CIRCEC-480
P2128 2128 APP SEN 2/CIRCEC-480
P2135 2135 TP SENSOREC-487
DTC*1
Items
(CONSULT-II screen terms)Reference page
CONSULT-II
GST*
2ECM*3
Page 1086 of 2771
EC-12
< SERVICE INFORMATION >
INDEX FOR DTC
*1: 1st trip DTC No. is the same as DTC No.
*2: This number is prescribed by SAE J2012.
*3: In Diagnostic Test Mode II (Self-diagnostic results), this number is controlled by NISSAN.
*4: The troubleshooting for this DTC needs CONSULT-II.
*5: When the fail-safe operations for both self-diagnoses occur, the MIL illuminates.
Alphabetical IndexINFOID:0000000001702547
NOTE:
•If DTC U1000 or U1001 is displayed with other DTC, first perform the trouble diagnosis for DTC
U1000, U1001. Refer to EC-143
.
•If DTC U1010 is displayed with other DTC, first perform the trouble diagnosis for DTC U1010.
Refer to EC-145
.
P2138 2138 APP SENSOREC-493
P2A00 2A00 A/F SENSOR1 (B1)EC-500
DTC*1
Items
(CONSULT-II screen terms)Reference page
CONSULT-II
GST*
2ECM*3
Items
(CONSULT-II screen terms)DTC*1
Reference page
CONSULT-II
GST*
2ECM*3
A/F SENSOR1 (B1) P0130 0130EC-206
A/F SENSOR1 (B1) P0131 0131EC-213
A/F SENSOR1 (B1) P0132 0132EC-219
A/F SENSOR1 (B1) P0133 0133EC-225
A/F SENSOR1 (B1) P2A00 2A00EC-500
A/F SEN1 HTR (B1) P0031 0031EC-151
A/F SEN1 HTR (B1) P0032 0032EC-151
A/T 1ST GR FNCTN P0731 0731AT- 1 0 5
A/T 2ND GR FNCTN P0732 0732AT- 1 0 8
A/T 3RD GR FNCTN P0733 0733AT- 111
A/T 4TH GR FNCTN P0734 0734AT- 11 4
A/T TCC S/V FNCTN P0744 0744AT- 1 2 4 (A/T),
CVT-93
(CVT)
APP SEN 1/CIRC P2122 2122EC-474
APP SEN 1/CIRC P2123 2123EC-474
APP SEN 2/CIRC P2127 2127EC-480
APP SEN 2/CIRC P2128 2128EC-480
APP SENSOR P2138 2138EC-493
ASCD BRAKE SW P1572 1572EC-438
ASCD SW P1564 1564EC-432
ASCD VHL SPD SEN P1574 1574EC-447
ATF TEMP SEN/CIRC P0710 0710AT- 9 1 (A/T),
CVT-71
(CVT)
BRAKE SW/CIRCUIT P1805 1805EC-452
CAN COMM CIRCUIT U1000
1000*4EC-143
CAN COMM CIRCUIT U1001
1001*4EC-143
CKP SEN/CIRCUIT P0335 0335EC-295
Page 1087 of 2771
INDEX FOR DTC
EC-13
< SERVICE INFORMATION >
C
D
E
F
G
H
I
J
K
L
MA
EC
N
P OC L O S E D L O O P - B 1 P 11 4 8 11 4 8EC-411
CMP SEN/CIRC-B1 P0340 0340EC-302
COLD START CONTROL P1421 1421EC-430
CONTROL UNIT(CAN) U1010 1010EC-145
CTP LEARNING P1225 1225EC-426
CTP LEARNING P1226 1226EC-428
CYL 1 MISFIRE P0301 0301EC-284
CYL 2 MISFIRE P0302 0302EC-284
CYL 3 MISFIRE P0303 0303EC-284
CYL 4 MISFIRE P0304 0304EC-284
ECM P0605 0605EC-397
ECT SEN/CIRC P0117 0117EC-187
ECT SEN/CIRC P0118 0118EC-187
ECT SENSOR P0125 0125 EC-198
ENG OVER TEMP P1217 1217EC-412
ENGINE SPEED SIG P0725 0725AT- 1 0 1
ETC ACTR P2119 2119EC-472
ETC FUNCTION/CIRC P2101 2101EC-461
ETC MOT P2118 2118EC-467
ETC MOT PWR P2100 2100EC-456
ETC MOT PWR P2103 2103EC-456
EVAP GROSS LEAK P0455 0455EC-370
EVAP PURG FLOW/MON P0441 0441EC-313
EVAP SMALL LEAK P0442 0442EC-318
EVAP SYS PRES SEN P0451 0451EC-351
EVAP SYS PRES SEN P0452 0452EC-355
EVAP SYS PRES SEN P0453 0453EC-362
EVAP VERY SML LEAK P0456 0456EC-377
FTT SEN/CIRCUIT P0182 0182EC-274
FTT SEN/CIRCUIT P0183 0183EC-274
FTT SENSOR P0181 0181EC-270
FUEL LEV SEN SLOSH P0460 0460EC-385
FUEL LEVEL SENSOR P0461 0461EC-387
FUEL LEVL SEN/CIRC P0462 0462EC-389
FUEL LEVL SEN/CIRC P0463 0463EC-389
FUEL SYS-LEAN-B1 P0171 0171EC-257
FUEL SYS-RICH-B1 P0172 0172EC-264
HO2S2 (B1) P0137 0137EC-233
HO2S2 (B1) P0138 0138EC-240
HO2S2 (B1) P0139 0139EC-250
HO2S2 HTR (B1) P0037 0037EC-156
HO2S2 HTR (B1) P0038 0038EC-156
Items
(CONSULT-II screen terms)DTC*1
Reference page
CONSULT-II
GST*
2ECM*3
Page 1088 of 2771
EC-14
< SERVICE INFORMATION >
INDEX FOR DTC
IAT SEN/CIRCUIT P0112 0112EC-182
IAT SEN/CIRCUIT P0113 0113EC-182
IAT SENSOR P0127 0127EC-201
INPUT SPD SEN/CIRC P0715 0715EC-450
IN PULY SPEED P1715 1715EC-449 (A/T),
EC-450
(CVT)
INT/V TIM CONT-B1 P0011 0011EC-147
INT/V TIM V/CIR-B1 P0075 0075EC-162
ISC SYSTEM P0506 0506EC-393
ISC SYSTEM P0507 0507EC-395
KNOCK SEN/CIRC-B1 P0327 0327EC-291
KNOCK SEN/CIRC-B1 P0328 0328EC-291
LU-SLCT SOL/CIRC P1740 1740CVT-132
L/PRESS SOL/CIRC P0745 0745AT- 1 2 9
MAF SEN/CIRCUIT P0101 0101EC-167
MAF SEN/CIRCUIT P0102 0102EC-175
MAF SEN/CIRCUIT P0103 0103EC-175
MULTI CYL MISFIRE P0300 0300EC-284
NATS MALFUNCTION P1610 - P1615 1610 - 1615BL-210
NO DTC IS DETECTED.
FURTHER TESTING
MAY BE REQUIRED.P0000 0000 —
O/R CLTCH SOL/CIRC P1760 1760AT- 1 4 4
P-N POS SW/CIRCUIT P0850 0850EC-405
PNP SW/CIRC P0705 0705AT- 8 6 (A/T),
CVT-65
(CVT)
PRS CNT SOL/A FCTN P0746 0746CVT-100
PRS CNT SOL/B CIRC P0778 0778CVT-104
PRS CNT SOL/B FCTN P0776 0776CVT-102
PURG VOLUME CONT/V P0443 0443EC-325
PURG VOLUME CONT/V P0444 0444EC-332
PURG VOLUME CONT/V P0445 0445EC-332
SENSOR POWER/CIRC P0643 0643EC-400
SFT SOL A/CIRC P0750 0750 AT- 1 3 4
SFT SOL B/CIRC P0755 0755AT- 1 3 9
STEP MOTR CIRC P1777 1777CVT-137
STEP MOTR FNC P1778 1778CVT-141
TCC SOLENOID/CIRC P0740 0740AT- 11 9
THERMSTAT FNCTN P0128 0128EC-204
TP SEN 1/CIRC P0222 0222EC-278
TP SEN 1/CIRC P0223 0223EC-278
TP SEN 2/CIRC P0122 0122EC-192
TP SEN 2/CIRC P0123 0123EC-192
TP SENSOR P2135 2135EC-487
Items
(CONSULT-II screen terms)DTC*1
Reference page
CONSULT-II
GST*
2ECM*3