width NISSAN X-TRAIL 2001 Service Workshop Manual

AT-462
[ALL]
REPAIR FOR COMPONENT PARTS
DISASSEMBLY
●Remove valves at retainer plate.
For removal procedures, refer to “DISASSEMBLY”,AT- 4 5 7 ,
"Control Valve Upper Body" .
INSPECTION
Valve Springs
●Check each valve spring for damage or deformation. Also mea-
sure free length and outer diameter.
●Replace valve springs if deformed or fatigued.
Control Valves
●Check sliding surfaces of control valves, sleeves and plugs for damage.
ASSEMBLY
●Install control valves.
For installation procedures, refer to “ASSEMBLY”, AT- 4 5 7 ,
"Control Valve Upper Body" .
Retainer Plate (Lower Body)
Unit: mm (in)
●Install proper retainer plates.
Refer to AT- 4 6 1 , "
Control Valve Lower Body" .
SAT550G
Inspection standard :Refer to AT- 5 2 1 , "SERVICE DATA
AND SPECIFICATIONS (SDS)" .
SAT138D
SAT550A
No. Name of control valve and plug Width A Length B Type
19 Pressure regulator valve
6.0
(0.236)28.0
(1.102)I 27 Accumulator control valve
30 Shift valve A
23 Overrun clutch control valve
2 Pressure modifier valve
35 Shuttle valve
9 Shift valve B — — II
SAT089F

AT-528
[ALL]
SERVICE DATA AND SPECIFICATIONS (SDS)
Input Shaft
ECS004MR
SEAL RING CLEARANCE
SEAL RING
*: Always check with the Parts Department for the latest parts information.
Reduction Pinion GearECS004MS
TURNING TORQUE
REDUCTION PINION GEAR BEARING ADJUSTING SHIMS
Input shaft seal ring clearance mm
(in)Standard 0.08 - 0.23 (0.0031 - 0.0091)
Allowable limit 0.23 (0.0091)
Outer diameter mm (in) 1nner diameter mm (in) Width mm (in) Part number*
26 (1.024) 22.4 (0.882) 1.97 (0.078) 31525 80X02
Turning torque of reduction pinion gear N·m (kg-cm, in-lb) 0.05 - 0.39 (0.5 - 4.0, 0.43 - 3.47)
NO. Thickness mm (in) Part number NO. Thickness mm (in) Part number*
1 5.00 (0.1969) 31439-81X00 33 5.64 (0.2220) 31439-81X63
2 5.02 (0.1976) 31439-81X01 34 5.66 (0.2228) 31439-81X64
3 5.04 (0.1984) 31439-81X02 35 5.68 (0.2236) 31439-81X65
4 5.06 (0.1992) 31439-81X03 36 5.70 (0.2244) 31439-81X66
5 5.08 (0.2000) 31439-81X04 37 5.72 (0.2252) 31439-81X67
6 5.10 (0.2008) 31439-81X05 38 5.74 (0.2260) 31439-81X68
7 5.12 (0.2016) 31439-81X06 39 5.76 (0.2268) 31439-81X69
8 5.14 (0.2024) 31439-81X07 40 5.78 (0.2276) 31439-81X70
9 5.16 (0.2031) 31439-81X08 41 5.80 (0.2283) 31439-81X71
10 5.18 (0.2039) 31439-81X09 42 5.82 (0.2291) 31439-81X72
11 5.20 (0.2047) 31439-81X10 43 5.84 (0.2299) 31439-81X73
12 5.22 (0.2055) 31439-81X11 44 5.86 (0.2307) 31439-81X74
13 5.24 (0.2063) 31439-81X12 45 4.60 (0.1811) 31439-85X01
14 5.26 (0.2071) 31439-81X13 46 4.62 (0.1819) 31439-85X02
15 5.28 (0.2079) 31439-81X14 47 4.64 (0.1827) 31439-85X03
16 5.30 (0.2087) 31439-81X15 48 4.66 (0.1835) 31439-85X04
17 5.32 (0.2094) 31439-81X16 49 4.68 (0.1843) 31439 85X05
18 5.34 (0.2102) 31439-81X17 50 4.70 (0.1850) 31439 85X06
19 5.36 (0.2110) 31439-81X18 51 4.72 (0.1858) 31439 83X11
20 5.38 (0.2118) 31439-81X19 52 4.74 (0.1866) 31439 83X12
21 5.40 (0.2126) 31439-81X20 53 4.76 (0.1874) 31439 83X13
22 5.42 (0.2134) 31439-81X21 54 4.78 (0.1882) 31439 83X14
23 5.44 (0.2142) 31439-81X22 55 4.80 (0.1890) 31439 83X15
24 5.46 (0.2150) 31439-81X23 56 4.82 (0.1898) 31439 83X16
25 5.48 (0.2157) 31439-81X24 57 4.84 (0.1906) 31439 83X17
26 5.50 (0.2165) 31439-81X46 58 4.86 (0.1913) 31439 83X18
27 5.52 (0.2173) 31439-81X47 59 4.88 (0.1921) 31439 83X19
28 5.54 (0.2181) 31439-81X48 60 4.90 (0.1929) 31439 83X20
29 5.56 (0.2189) 31439-81X49 61 4.92 (0.1937) 31439 83X21
30 5.58 (0.2197) 31439-81X60 62 4.94 (0.1945) 31439 83X22
31 5.60 (0.2205) 31439-81X61 63 4.96 (0.1953) 31439 83X23
32 5.62 (0.2213) 31439-81X62 64 4.98 (0.1961) 31439 83X24

SERVICE DATA AND SPECIFICATIONS (SDS)
AT-529
[ALL]
D
E
F
G
H
I
J
K
L
MA
B
AT
*: Always check with the Parts Department for the latest parts information.
Band ServoECS004MT
RETURN SPRING
Unit: mm (in)
*: Always check with the Parts Department for the latest parts information.
Output ShaftECS004MU
SEAL RING CLEARANCE
SEAL RING
*: Always check with the Parts Department for the latest parts information.
END PLAY
OUTPUT SHAFT ADJUSTING SHIMS
*: Always check with the Parts Department for the latest parts information.
Bearing RetainerECS004MV
SEAL RING CLEARANCE
Total End PlayECS004MW
Return spring Part number* Free length Outer diameter
2nd servo return spring 31605-31X20 32.5 (1.280) 25.9 (1.020)
OD servo return spring 31605-80X07 31.0 (1.220) 62.6 (2.465)
Output shaft seal ring clearance mm
(in)Standard 0.10 - 0.25 (0.0039 - 0.0098)
Allowable limit 0.25 (0.0098)
Outer diameter mm (in) 1nner diameter mm (in) Width mm (in) Part number*
33.71 (1.327) 30.25 (1.191) 1.95 (0.077) 31525 80X09
Output shaft end play mm (in) 0 - 0.15 (0 - 0.0059)
Thickness mm (in) Part number*
0.80 (0.0315)
0.84 (0.0331)
0.88 (0.0346)
0.92 (0.0362)
0.96 (0.0378)
1.00 (0.0394)
1.04 (0.0409)
1.08 (0.0425)
1.12 (0.0441)
1.16 (0.0457)
1.20 (0.0472)31438-80X60
31438-80X61
31438-80X62
31438-80X63
31438-80X64
31438-80X65
31438-80X66
31438-80X67
31438-80X68
31438-80X69
31438-80X70
Bearing retainer seal ring
clearance mm (in)Standard 0.10 - 0.30 (0.0039 - 0.0118)
Allowable limit 0.30 (0.0118)
Total end play mm (in) 0.25 - 0.55 (0.0098 - 0.0217)

BR-32
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
PFP:00030
General SpecificationsEFS000CQ
Unit: mm (in)
Brake PedalEFS000CR
Check ValveEFS000CS
Brake BoosterEFS000CT
Vacuum type
Front Disc BrakeEFS000CU
Front brakeBrake model AD31VD
Cylinder bore diameter 44.4 × 2 (1.748 × 0.08)
Pad
Length x width x thickness132.0 × 52.5 × 11.0
(5.20 × 2.067 × 0.433)
Rotor outer diameter x thickness 280 × 28 (11.02 × 1.10)
Rear brakeBrake model AD9VA
Cylinder bore diameter 34.9 (1.374)
Pad
Length x width x thickness83.0 × 33.0 × 8.5
(3.268 × 1.299 × 0.335)
Rotor outer diameter x thickness 292 × 16 (11.50 × 0.63)
Master cylinder Cylinder bore diameter 25.4 (1)
Control valve Valve model Electronic control type
Brake boosterBooster model C215T
Diaphragm diameterPrimary 230 (9.06)
Secondary 205 (8.07)
Recommended brake fluid DOT 3 or DOT 4
Free play (at pedal top surface) 3 - 11 mm (0.12 - 0.43 in)
Looseness at clevis pin 1 - 3 mm (0.04 - 0.12 in)
Brake pedal height (from dash panel top surface)M/T model 156 - 166 mm (6.14 - 6.54 in)
A/T model 164 - 174 mm (6.46 - 6.85 in)
Depressed pedal height under force of 490 N (50 kg,110.6 lb)
(from dash panel top surface)M/T model 80 mm (3.15 in) or more
A/T model 85 mm (3.35 in) or more
Clearance between threaded end of stop lamp switch and pedal stopper 0.74 - 1.96 mm (0.0291 - 0.0772 in)
Vacuum leakage [at vacuum of 66.7 kPa (-500 mmHg, -19.69
inHg)]Within 1.3 kPa (10 mmHg, 0.39 inHg) of vacuum for 15 sec-
onds
Vacuum leakage [at vacuum of -66.7 kPa (-500 mmHg, -19.69
inHg)]Within 3.3 kPa (25 mmHg, 0.98 inHg) of vacuum for 15 sec-
onds
Input rod installation standard dimension 125 mm (4.92 in)
Brake typeAD31VD
Brake padStandard thickness (new) 11 mm (0.43 in)
Repair limit thickness 2.0 mm (0.07 in)
Disc rotorStandard thickness (new) 28 mm (1.10 in)
Repair limit thickness 26 mm (1.02 in)
Runout limit 0.04 mm (0.0016 in)

ENGINE MAINTENANCE (YD22DDTI)
MA-33
C
D
E
F
G
H
I
J
K
MA
B
MA
Changing Oil FilterELS000CI
REMOVAL
CAUTION:
●Be careful not to get burned when the engine and engine oil
are hot.
●When removing, prepare a shop cloth to absorb any engine
oil leakage or spillage.
●Do not allow engine oil to adhere to the drive belts.
●Completely wipe off any engine oil that adhere to the engine
and the vehicle.
1. Using a socket wrench [plane-to-plane width: 17 mm (0.67 in)],
loosen the filter body approximately four turns.
2. Drain the engine oil after matching the "DRAIN" arrow mark at
the bottom of the filter body to the protrusion on the oil filter
bracket.
●Catch the engine oil with a pan or cloth.
CAUTION:
●The drained engine oil flows over the right surface of
the filter body.
●Completely wipe clean any engine oil remaining on the
filter body or vehicle.
3. Remove the filter body, then remove the oil filter.
PBIC1248E
JLC290B
JLC291B