instrument cluster NISSAN X-TRAIL 2001 Service Repair Manual

IP-1
INSTRUMENT PANEL
I BODY
CONTENTS
C
D
E
F
G
H
J
K
L
M
SECTION
A
B
IP
INSTRUMENT PANEL
PRECAUTIONS .......................................................... 2
Precautions for Supplemental Restraint System
(SRS) “AIR BAG” and “SEAT BELT PRE-TEN-
SIONER” .................................................................. 2
Precautions .............................................................. 2
INSTRUMENT PANEL ASSEMBLY ........................... 3
Component Parts Drawing ....................................... 3
Removal and Installation .......................................... 5
TABLE OF WORK ITEM ....................................... 5
FRONT SPEAKER GRILLE .................................. 6
INSTRUMENT FINISHER ..................................... 6
CUP HOLDER ....................................................... 6
CLUSTER LID A ................................................... 6
COMBINATION METER ....................................... 6
POCKET ............................................................... 6
STEERING COLUMN COVER ............................. 6
INSTRUMENT LOWER DRIVER PANEL ............. 7
MIRROR CONTROL SWITCH .............................. 7
GPS ANTENNA .................................................... 7
CLUSTER LID C ................................................... 7CLUSTER LID FINISHER ..................................... 7
AUDIO UNIT AND POCKET ................................. 7
HEATER CONTROL FINISHER ............................ 8
CD AUTO–CHANGER AND POCKET .................. 8
HEATER CONTROLLER ....................................... 8
A/T OR M/T FINISHER ......................................... 8
CONSOLE MASK AND CENTER CONSOLE ....... 8
LOWER INSTRUMENT COVER ........................... 8
INSTRUMENT LOWER CENTER PANEL ............ 8
GLOVE BOX ......................................................... 9
LOWER INSTRUMENT PANEL ............................ 9
GLOVE BOX COVER ............................................ 9
FRONT PASSENGER AIR BAG MODULE ........... 9
INSTRUMENT REINFORCEMENT ....................... 9
INSTRUMENT MASK ............................................ 9
FRONT PILLAR GARNISH ................................... 9
INSTRUMENT PANEL .......................................... 9
Disassembly and Assembly .................................... 10
CONSOLE BOX ASSEMBLY .............................. 10

IP-4
INSTRUMENT PANEL ASSEMBLY
1. Front passenger air bag module 2. Front speaker grille (right) 3. Front side speaker (right)
4. Cup holder (right) 5. Instrument finisher B 6. Combination meter
7. Instrument mask (right) 8. GPS antenna 9. Instrument mask (left)
10. Instrument cluster lid A 11. Pocket 12. Front speaker grille (left)
13. Front side speaker (left) 14. Cup holder (left) 15. Mirror control switch
16. Instrument panel & pad 17. Instrument reinforcement 18. Audio unit and pocket
19. Glove box cover 20. Lower instrument panel 21. Glove box pin
22. Glove box 23. Cluster lid C 24. Instrument finisher A
25. Instrument lower driver panel 26. Column cover, key cylinder escutcheon 27. Cluster lid finisher (left)
28. Heater control finisher 29. CD auto–changer and pocket 30. instrument lower center panel
31. Lower instrument cover 32. Cluster lid finisher (right) 33. Center console
34. A/T or M/T finisher 35. Console mask 36. Seal case (inner case)

INSTRUMENT PANEL ASSEMBLY
IP-5
C
D
E
F
G
H
J
K
L
MA
B
IP
Removal and InstallationEIS000NI
TABLE OF WORK ITEM
[ ]: The number shows the removal order.
ComponentsInstrument
panelCombination
meterNavigation
DisplayAudio
Console
Up Down
Front speaker grille [1]
Instrument finisher A, B [2] [1]
Cup holder [3]
Instrument cluster lid A [4] [2]
Combination meter [5] [3]
Pocket [6]
Key cylinder escutcheon and steer-
ing column cover[7]
Instrument lower driver panel [8]
Mirror control switch [9]
GPS antenna [10]
Cluster lid C [11] [1] [1]
Cluster lid finisher [12] [1] [1]
Audio unit and pocket [13] [2] [2]
Heater control finisher [14] [2]
CD auto–changer and pocket [15] [3]
Heater controller [16]
A/T(M/T,CVT) finisher [17] [2]
Console mask [18] [3]
Center console [19] [4]
Lower instrument cover [20]
instrument lower center panel [21]
Glove box [22]
Lower instrument panel [23]
Glove box cover [24]
Front passenger air bag module [25]
Instrument reinforcement [26]
Instrument mask [27]
Front pillar garnish [28]
Instrument panel [29]

IP-6
INSTRUMENT PANEL ASSEMBLY
FRONT SPEAKER GRILLE
●Pull forward and remove front speaker grille.
INSTRUMENT FINISHER
●Remove clips starting from the outside.
CUP HOLDER
●Remove screws and remove cup holder.
CLUSTER LID A
●Remove screws, and pull instrument cluster lid A forward to
unfasten clip.
COMBINATION METER
●Remove screws, and remove connector. Then remove combination meter.
POCKET
●Remove screws and remove pocket.
STEERING COLUMN COVER
●Remove key cylinder escutcheon first. Remove screws.
SIIA0226E
SIIA0227E
SIIA0228E

INSTRUMENT PANEL ASSEMBLY
IP-7
C
D
E
F
G
H
J
K
L
MA
B
IP
INSTRUMENT LOWER DRIVER PANEL
●Remove screws, and pull driver-side instrument lower panel
straight forward to unfasten the clip.
MIRROR CONTROL SWITCH
1. From the back, press tab on mirror control switch to remove. Or insert a screwdriver, wrapped with a
cloth, into lower side of the switch to unfasten the lower clip.
2. Disconnect connector and then remove mirror control switch.
GPS ANTENNA
●Remove screws and Disconnect connector.
CLUSTER LID C
1. Insert a clip remover or similar tool into lower side of cluster lid C
and unfasten clip.
2. Unfasten resin tabs on upper and lower sides and remove clus-
ter lid C.
CLUSTER LID FINISHER
●Insert a clip clamp remover or similar tool into center panel gap
and unfasten clip.
AUDIO UNIT AND POCKET
Remove mounting screws on audio unit and pocket.Disconnect connector and remove audio unit and pocket.
NOTE:
During removal or installation, use cloth to protect surrounding area from damage.
SIIA0230E
SIIA0229E
PIIA3749E

DUCTS AND GRILLES
ATC-127
C
D
E
F
G
H
I
K
L
MA
B
AT C
DUCTS AND GRILLESPFP:27860
Removal and InstallationEJS000UX
VENTILATOR DUCT, DEFROSTER NOZZLE AND DEFROSTER DUCTS
NOTE:
This illustration is for RHD models. The layout for LHD models is symmetrically opposite.
CENTER VENTILATOR GRILLE
Remove the cluster lid C. Refer to IP-5, "Removal and Installation" in the Instrument Panel assembly.
SIDE VENTILATOR GRILLE
1. Remove the instrument panel.
2. Remove the side ventilator grille.
RJIA0067E
RJIA0068E

DUCTS AND GRILLES
MTC-29
C
D
E
F
G
H
I
K
L
MA
B
MTC
DUCTS AND GRILLESPFP:27860
Removal and InstallationEJS000XW
VENTILATOR DUCT, DEFROSTER NOZZLE AND DEFROSTER DUCTS
1. Remove the instrument panel.
CENTER VENTILATOR GRILLE
1. Remove the cluster lid C. Refer to IP-5, "Removal and Installation" .
SIDE VENTILATOR GRILLE
1. Remove the instrument panel. Refer to IP-5, "Removal and
Installation" .
2. Remove the side ventilator grille.
RJIA0067E
RJIA0068E

COMBINATION METERS (LHD MODELS)
DI-23
C
D
E
F
G
H
I
J
L
MA
B
DI
Removal and Installation for Combination MeterEKS002ZO
1. Remove the cluster lid A. Refer toIP-3, "INSTRUMENT PANEL
ASSEMBLY" .
2. Remove the screws (4), and pull out combination meter.
3. Disconnect connectors and remove combination meter.
Disassembly and Assembly for Combination MeterEKS002ZP
1. Disengaged the tabs(8) to separate front cover.
2. Remove finisher.
3. Remove bulbs.
SKIA0036E
SKIA0044E

DI-42
COMBINATION METERS (RHD MODELS)
THERMAL TRANSMITTER CHECK
Check the resistance between the terminals of thermal transmitter
and body ground.
Removal and Installation for Combination MeterEKS0030Z
1. Remove the cluster lid A. Refer to IP-3, "INSTRUMENT PANEL
ASSEMBLY" .
2. Remove the screws (4), and pull out combination meter.
3. Disconnect connectors and remove combination meter.
Disassembly and Assembly for Combination MeterEKS00310
1. Disengaged the tabs(8) to separate front cover.
2. Remove finisher.
3. Remove bulbs.
Water temperature Resistance
60°C (140°F) Approx. 170 - 210Ω
100°C (212°F) Approx. 47 - 53Ω
MEL424F
SKIA0036E
SKIA0044E

AUDIO
AV-13
C
D
E
F
G
H
I
J
L
MA
B
AV
InspectionEKS002F6
AUDIO UNIT
All voltage inspections are made with:
●Ignition switch ON or ACC
●Audio unit ON
●Audio unit connected (If audio unit is removed for inspection, supply a ground to the case using a jumper
wire.)
ANTENNA
Using a jumper wire, clip an auxiliary ground between antenna and body.
●If reception improves, check antenna ground (at body surface).
●If reception does not improve, check main feeder cable for short circuit or open circuit.
Removal and Installation of Audio UnitEKS002PU
1. Remove instrument cluster lid “C”.
● Refer to IP-7, "CLUSTER LID C" in “Instrument Panel (IP)” section.
2. Remove screws and connector, and then remove audio unit.
3. Remove screws, and then bracket.
SKIA0890E
SKIA0891E