headlamp NISSAN X-TRAIL 2003 Electronic Owner's Manual

HEADLAMP
LT-7
C
D
E
F
G
H
I
J
L
MA
B
LT
CAUTION:
Be sure aiming switch is set to “0” when performing aiming adjustment.
LOW BEAM
1. Turn headlamp low beam on.
LHD models
RHD models
2. Use adjusting screws to perform aiming adjustment.
lFirst tighten the adjusting screw all the way and then make adjustment by loosening the screw.
If the vehicle front body has been repaired and/or the headlamp assembly has been replaced, check aim-
ing. Use the aiming chart shown in the figure.
lAdjust headlamps so that main axis of light is parallel to cen-
ter line of body and is aligned with point P shown in illustra-
tion.
lFigure to the left shows headlamp aiming pattern for driv-ing
on right side of road; for driving on left side of road, aiming
pattern is reversed.
lDotted lines to point P in illustration show center of head-
lamp.
lBasic illuminating area for adjustment should be within the
range shown at left. Adjust headlamps accordingly.
CAUTION:
Be sure aiming switch is set to “0” when preforming aiming
adjustment."H" : Horizontal center line of headlamps
"W
L
": Distance between each headlamp center
"L" : 5,000mm (196.85 in)
"C" : 65mm (2.56 in)
PKIA0459E
SKIA0047E
SEL254L

LT-8
HEADLAMP
Bulb Replacement
EKS003CH
HEAD LAMP
1. Disconnect connector of headlamp.
2. Remove rubber cap.
3. Unlock retaining spring, then remove bulb.
CLEARANCE LAMP
1. Turn the RH bulbsocket clockwise and unlock it.
Turn the LH bulbsocket counterclockwise and unlock it.
2. Remove the bulb from its socket.
CAUTION:
lDo not touch the glass of bulb directly by hand. Keep grease and other oily matters away from it.
Do not touch bulb by hand while it is lit or right after being turned off. Burning may result.
lDo not leave bulb out of headlamp reflector for a long time because dust, moisture smoke, etc.
may affect the performance of headlamp. When replacing bulb, be sure to replace it with new one.
lWhen bulb is installed, be sure to lock rubber cap to ensure watertightness.
Removal and InstallationEKS003CI
REMOVAL
1. Remove the front turn signal lamps. Refer toLT-22, "Removal
and Installation for Front Turn Signal Lamp"
2. Disconnect connector of headlamp and clearance lamp.
3. Remove the front grille. Refer toEI-11, "
FRONT GRILL"in
"EXTERIOR & INTERIOR (EI)" section.
4. Remove the headlamp mounting bolts.
5. Pull the headlamp toward the front of the vehicle.
INSTALLATION
lInstall in the reverse order of removal, taking care of the following points.
Headlamp mounting screws and nutHeadlamp (High/Low) : 12V 60/55 W(H4)
SKIA0073E
Clearance lamp : 12V 5W
SKIA0050E
Tightening torque : 4.5 - 6.4 N-m (0.45 - 0.65 kg-m, 39 - 56 in-lb)

HEADLAMP - DAYTIME LIGHT SYSTEM -
LT-9
C
D
E
F
G
H
I
J
L
MA
B
LT
HEADLAMP - DAYTIME LIGHT SYSTEM -PFP:26010
System DescriptionEKS003BB
DESCRIPTION
The headlamp system on vehicles for North Europe contains a daytime light unit. The unit activates the follow-
ing whenever the engine is running with the lighting switch in the OFF position:
lLow beam headlamps
lParking, license, tail and illumination lamps
Power is supplied at all times
lthrough 10A fuse (No. 31, located in the fuse and fusible link box)
lto daytime light unit terminal 1 and
lto lighting switch terminal 11.
Power is also supplied at all times
lthrough 15A fuse (No. 41, located in the fuse and fusible link box)
lto daytime light unit terminal 3 and
lto lighting switch terminal 5.
Power is also supplied at all times
lthrough 15A fuse (No. 40, located in the fuse and fusible link box)
lto daytime light unit terminal 2 and
lto lighting switch terminal 8.
With the ignition switch in the ON or START position, power is supplied
lthrough 10A fuse [No. 13, located in the fuse block (J/B)]
lto daytime light unit terminal 7.
With the ignition switch in the START position, power is supplied
lthrough 10A fuse [No. 7, located in the fuse block (J/B)]
lto daytime light unit terminal 6.
HEADLAMP OPERATION (DAYTIME LIGHT CANCEL OPERATION)
When the lighting switch is turned to the 1st or 2nd position, power is supplied
lthrough lighting switch terminal 12,
lto daytime light unit terminal 11.
Then daytime light will be canceled. And the lighting system operation will be the same as no daytime light
system.
DAYTIME LIGHT OPERATION
With the engine running and the lighting switch in the OFF position, power is supplied
lfrom alternator terminal 3
lto daytime light unit terminal 8,
lthrough daytime light unit terminal 5
lto terminal 3 of headlamp LH,
lthrough daytime light unit terminal 4
lto terminal 3 of headlamp RH and
lthrough daytime light unit terminal 10
lto tail lamp and illumination.
Ground is supplied to terminal 2 of each headlamp through body grounds E24 and E50.

LT-10
HEADLAMP - DAYTIME LIGHT SYSTEM -
Schematic
EKS003BC
TKWA0060E

HEADLAMP - DAYTIME LIGHT SYSTEM -
LT-11
C
D
E
F
G
H
I
J
L
MA
B
LT
Wiring Diagram -DTRL-EKS003BD
TKWA0061E

LT-12
HEADLAMP - DAYTIME LIGHT SYSTEM -
TKWA0062E

HEADLAMP - DAYTIME LIGHT SYSTEM -
LT-13
C
D
E
F
G
H
I
J
L
MA
B
LT
TKWA0063E

LT-14
HEADLAMP - DAYTIME LIGHT SYSTEM -
Trouble Diagnoses
EKS003CO
DAYTIME LIGHT UNIT INSPECTION TABLE
*: Daytime light operating: Lighting switch in “OFF” position with engine running.
Bulb ReplacementEKS003CP
Refer toLT- 4 , "HEADLAMP"
Aiming AdjustmentEKS003BE
Refer toLT- 4 , "HEADLAMP"
Te r m i n a l
No.WIRE
COLORConnectionsINPUT (I)/
OUTPUT
(O)Operated conditionVo l ta g e (V )
(Approximate val-
ues)
1G/WPower source for illumi-
nation & tail lamp—— 12
2LGPower source for head-
lamp LH—— 12
3R/WPower source for head-
lamp RH—— 12
4G/YHeadlampRH OON (daytime light operating*) 12
OFF 0
5Y/GHeadlampLH OON (daytime light operating*) 12
OFF 0
6 B/Y Start signal I Ignition switchSTART 12
ON, ACC or OFF 0
7 BR Power source — Ignition switchON or START 12
ACC or OFF 0
8 Y/R Alternator “L” terminal I EngineRunning 12
Stopped 0
9 B Ground — — —
10 R/L Illumination & tail lamp OON (daytime light operating*) 12
OFF 0
11 R/L Lighting switch I1ST·2ND position 12
OFF 0

HEADLAMP AIMING CONTROL
LT-15
C
D
E
F
G
H
I
J
L
MA
B
LT
HEADLAMP AIMING CONTROLPFP:26010
Wiring Diagram -H/AIM-EKS003BF
TKWA0064E

LT-16
HEADLAMP AIMING CONTROL
Removal and Installation
EKS003CA
1. Remove the Instrument lower driver panel . Refer toIP-5,
"Removal and Installation"in “INSTRUMENT PANEL (IP)” sec-
tion.
2. Press the headlamp aiming switch fixing tabs and remove the
unit from the Instrument lower driver panel.
Switch Circuit InspectionEKS003CB
Using a circuit tester, check continuity between the headlamp aiming
switch connector terminals in each operation status of the aiming
switch.
SKIA0062E
SKIA1168E