wheel OLDSMOBILE AURORA 1996 Owner's Guide

12. Try to start the vehicle with the dead battery. If
it won’t start after a few tries, it probably needs
service.
13. Remove the cables in reverse order to prevent electrical shorting. Take care that they don’t touch
each other or any other metal.
- +
B
A. Heavy Metal Engine Part
B . Good Battery
C. Dead Battery
Towing Your Vehicle
Try to have a GM dealer or a professional towing
service tow your vehicle.
If your vehicle has been changed or modified since it
was factory-new by adding aftermarket items like fog
lamps, aero skirting, or special tires and wheels, these
instructions and illustrations may not be correct.
Before you do anything, turn on the hazard warning
flashers.
When you call, tell the towing service:
That your vehicle can only be towed from the front
0 That your vehicle has front-wheel drive.
0 The make, model and year of your vehicle.
0 Whether you can still move the shift lever.
If there was an accident, what was damaged.
When the towing service arrives, let the tow operator
know that this manual contains detailed towing
instructions and illustrations. The operator may want to
see them. with
sling type equipment.
ProCarManuals.com

I. CAUTION:
--
A vehicle can fall from a car carrier if it isn’t
adequately secured. This can cause
a collision,
serious personal injury and vehicle damage. The
vehicle should be tightly secured with chains or
steel cables before it is transported.
Don’t use substitutes (ropes, leather straps,
canvas webbing, etc.) that can be cut by sharp
edges underneath the towed vehicle. Always use
T-hooks inserted in the T-hook slots. Never use
J-hooks. They will damage drivetrain and
suspension components. When
your vehicle is being towed, have the ignition key
turned to the
OFF position. The steering wheel should
be clamped in a straight-ahead position, with
a clamping
device designed for towing service.
Do not use the
vehicle’s steering column lock for this. The transaxle
should be in
NEUTRAL (N) and the parking brake
released.
Don’t have your vehicle towed on the drive wheels,
unless you must. If the vehicle must be towed on the
drive wheels, be sure
to follow the speed and distance
restrictions later in this section or your transaxle will be
damaged.
If these limitations must be exceeded, then the
drive wheels have to be supported on a dolly.
ProCarManuals.com

Front Towing
NOTICE:
Do not tow with sling-type equipment or
fascidfog lamp damage will occur.
Use wheel-lift
or car carrier equipment. Additional ramping
may be required for car carrier equipment. Use
safety chains and wheel straps.
Towing
a vehicle over rough surfaces could
damage
a vehicle. Damage can occur from vehicle
to ground
or vehicle to wheel-lift equipment. To
help avoid damage, install a towing dolly and
raise the vehicle until adequate clearance is
obtained between the ground and/or wheel-lift
equipment.
Do not attach winch cables or J-hooks to
suspension components when using car carrier
equipment. Always use T-hooks inserted in the
T-hook slots.
5-11
ProCarManuals.com

These slots are to be used when loading and securing to
car carrier equipment.
Attach T-hook chains on both sides, in the slotted holes
in the bottom
of the body rail, behind the front wheels
and cradle. Attach a separate safety chain around the outboard
end
of each lower control arm.
NOTICE:
Be sure not to attach the safety chain to the drive
axle. This could cause damage to the drive axle
boot.
ProCarManuals.com

Rear Towing
TQW Limits -- 55 mph (88 kmlh), 500 miles (800 h)
Attach T-hook chains to the T-hook slots in the floor pan
supportrails
just ahead of the rear wheels on both sides.
Position the lower sling crossbar just ahead of the front
edge
oi the rear bumper.
5-13
ProCarManuals.com

If a Tire Goes Flat
It’s unusual for a tire to “blow out” while you’re driving,
especially if you maintain your tires properly.
If air goes
out of a tire, it’s much more likely to leak out slowly.
But if you should ever have a “blowout,” here
are a few
tips about what to expect and what to do:
If a front tire fails, the flat tire will create a drag that
pulls the vehicle toward that side. Take your foot off the
accelerator pedal and grip the steering wheel firmly.
Steer to maintain lane position, and then gently brake to
a stop well out
of the traffic lane.
A rear blowout, particularly on a curve, acts much like a
skid and may require the same correction you’d use
in a
skid. In any rear blowout, remove your foot from the
accelerator pedal. Get the vehicle under control by
steering the way you want the vehicle to go. It may be
very bumpy and noisy, but you can still steer. Gently
brake to a stop
-- well off the road if possible.
If a tire goes flat, the next part shows how to use your
jacking equipment to change a flat tire safely.
Changing a Flat Tire
If a tire goes flat, avoid further tire and wheel damage
by driving slowly to a level place. Turn on your hazard
warning flashers.
I /d CAUTIO,
Changing a tire can cause an injury. The vehicle
can slip
off the jack and roll over you or other
people.
You and they could be badly injured.
Find
a level place to change your tire. To help
prevent the vehicle from moving:
1. Set the parking brake firmly.
2. Put the shift lever in PARK (P).
3. Turn off the engine.
To be even more certain the vehicle won’t move,
you can put blocks
at the front and rear of the
tire farthest away from the one being changed.
That would be the tire on the other side of the
vehicle, at the opposite end.
ProCarManuals.com

Turn the spare tire retainer
bolt counterclockwise and
remove the retainer assembly.
Remove the wheel wrench and jack from the jack container.
Remove the spare tire from the trunk.
ProCarManuals.com

A
m
The tools you'll be using include the jack (A) and the
wheel wrench
(B).
Insert the hooked end of the wheel wrench in one of the
two small notches in the center cover and pry the cover
off. Do not drop the cover or lay it face down, as it
could be scratched or damaged.
Do not use a hammer or mallet to install the cover
when replacing the cover after the wheel
is put back
on the vehicle.
ProCarManuals.com

Removing the Flat Tire and Installing the
Spare Tire 2. Insert the pointed end of the wheel wrench into the
slot on the jack to create a jack handle.
3. Turn the end of the jack
clockwise
by hand to
raise the jack head a few
inches.
1. Use the wheel wrench to loosen the wheel nuts, but
don’t remove them.
ProCarManuals.com

CF I
II
I 11 INCHES -1 I- (28CM) & -1z INCHES 1
(19CM)
4. Near each wheel well is a notch in the frame to
position the jack head. You'll find the word
JACK
and an arrow stamped into the plastic near each
notch. Position the jack under the vehicle and raise
the jack head until it fits firrnly against the sheet
metal next to the word
JACK. Do not raise the
vehicle
yet. Put the compact spare near you.
1
Getting under a vehicle when it is jacked up is
dangerous.
If the vehicle slips off the jack, you
could be badly injured
or killed. Never get under
a vehicle when it is supported only by a jack.
NOTICE:
Raising your vehicle with the jack improperly
positioned will damage the vehicle or may allow
the vehicle to
fall off the jack. Be sure to fit the
jack lift head into the proper location before raising your vehicle.
ProCarManuals.com