OLDSMOBILE AURORA 2002 Owners Manual

3-5
In cold weather, the system will delay turning on the fan
to avoid blowing cold air into the vehicle. The length of
the delay depends on the engine coolant temperature and
the outside temperature. Turning the right mode knob
will override this delay by turning off the automatic
mode and changing the fan speed.
Your automatic electronic climate control system has a
sun sensor located on the top of the instrument panel
that detects direct sunlight. To keep you and your
passengers comfortable, the system may supply cooler
air to the side of the vehicle toward the sun. Be careful
not to put anything over this sun sensor. The automatic
electronic climate control system may not operate
correctly if this sensor is covered.
To change the automatic electronic climate control
display from an English display to a metric display, push
the OFF button located in the Driver Information Center
(DIC) for two seconds. The display in the DIC will also
change from an English to a metric display. To return to
an English display, repeat the above procedure.Passenger Temperature Control (Option)
With this feature, the right
front seat passenger can
control the temperature
setting for his or her own
zone. To use this feature,
turn the knob on the
passenger's door clockwise
or counterclockwise to a
cooler or warmer setting.
The temperature can be set up to 8
F (4
C) cooler or
warmer than the main setting.
ProCarManuals.com

3-6 Comfort Controls Personalization
(If Equipped)
This feature enables up to two drivers to store and recall
comfort control settings for temperature, air delivery
mode and fan speed.
The memory buttons (1 or 2) for this feature are located
on the driver's door panel and correspond to the
numbers (1 or 2) found on the back of each remote
keyless entry transmitter.
To recall comfort settings, press the unlock button
on the remote keyless entry transmitter and put the
ignition in ACC (Accessory) or ON. The climate
control setting last chosen by the identified
driver (1 or 2) will be recalled.
To program a personal climate control setting, do
the following:
1. Choose a climate control setting for the driver
and if desired, for the passenger. See ªAutomatic
Electronic Climate Controlº and ªPassenger
Temperature Control (Option)º earlier in this section.
2. Adjust the direction of the airflow.3. Locate the memory buttons on the driver's
door panel.
4. Press a memory button (1 or 2) until you hear two
beeps. The beeps confirm that your selection has
been saved and can now be recalled.
Follow these steps each time you want to change the
stored settings. For more information on the memory
feature, see ªMemory Seat and Mirrorsº in the Index.
Air Conditioning
The air conditioner cools and dehumidifies the air inside
of the vehicle.
The air conditioning compressor is enabled in all
modes unless the air conditioning button is not selected
(the indicator light will not be illuminated). However,
the air conditioning compressor will not operate when
the outside temperature is below 34
F (1
C). When the
air conditioner is on, you may sometimes notice slight
changes in your vehicle's engine speed and power. This
is normal, because the system is designed to cycle the
compressor on and off to maintain the desired
temperature and to help with fuel economy.
ProCarManuals.com

3-7
On very hot days, open the windows long enough to let
the hot air out. This reduces the time required to cool the
interior of the vehicle to a comfortable temperature. If
the system is in the automatic mode (left and right mode
knob indicator lights are on), during very hot days the
system will automatically go to the recirculation mode
and the temperature door will initially be at the full cold
position for maximum cooling. You can choose the
extreme temperature setting of 60
F (16
C), but the
system will not cool any faster by choosing this setting.
Heating
In cold weather, if the automatic mode is selected
(left and right mode knob indicator lights are on), the
system will automatically direct the airflow out of the
floor ducts and the temperature door will initially be
positioned at the full hot position. You can choose
the extreme temperature setting of 90
F (32
C),
but the system will not warm up any faster by selecting
this setting.In cold weather, the system will delay turning on the fan
to avoid blowing cold air into the vehicle. The length of
the delay depends on the engine coolant temperature and
the outside temperature. The fan speed will increase as
the temperature of the engine coolant rises. Turning the
right mode knob will override this delay by cancelling
the automatic fan control mode.
Defogging and Defrosting
On cool, humid days, use the defog setting to keep
the windows clear while also providing heat through
the floor ducts. Turn the left mode knob clockwise
to defrost to quickly remove fog or ice from
the windshield.
For maximum front defrost performance under extreme
icing or frosting conditions, increase the temperature
setting to 90
F (33
C) and increase the fan speed
to high.
ProCarManuals.com

3-8 Rear Window Defogger
(Rear Defogger):
Press this button to
warm the defogger
grid on the rear
window. An indicator
light below the button
will glow while the
rear window defogger
is operating.
At speeds above 30 mph (48 km/h), the rear defogger
will stay on until you press the rear button again. At
speeds below 30 mph (48 km/h), the rear defogger will
turn off automatically after about 10 minutes of use. If
you press it again, the defogger will operate for about
five minutes only. You can also turn the defogger off
by turning off the ignition.
Do not attach a temporary vehicle license across the
defogger grid on the rear window.
If your vehicle is equipped with heated outside rearview
mirrors, when you operate the rear window defogger,
the mirrors are also heated to help remove ice and fog.
For more information see ªHeated Outside Rearview
Mirrorsº in the Index.
NOTICE:
Don't use a razor blade or other sharp object on
the inside of the rear window. If you do, you
could cut or damage the warming grid, and the
repairs wouldn't be covered by your warranty.
Ventilation System
Your vehicle's flow-through ventilation system allows
filtered outside air to flow through your vehicle while it
is moving, even if the system is off.
The direction of the airflow
can be controlled by
adjusting/closing the outlets
in the instrument panel.
ProCarManuals.com

3-9
Turn the thumbwheel between the front outlets to
open and close the outlets. Adjust the direction of
airflow from side to side with the levers in the center
of each outlet.
Move the control between the rear outlets up to direct
airflow through the upper outlets. Move the control
down to direct airflow through the floor ducts. Adjust
the direction of airflow from side to side with the levers
located in the center of each outlet.Ventilation Tips

Keep the hood and front air inlet area between the
base of the windshield and the hood free of ice,
snow, or any other obstruction (such as leaves).
The defroster and heater will work far better,
reducing the chance of fogging the inside of your
windows, if this area is clear.

Keep the air path under the front seats clear
of objects. This helps air to circulate throughout
your vehicle.
ProCarManuals.com

3-10 Steering Wheel Controls for
Climate Control
Some heating and cooling
controls can be adjusted
at the steering wheel.
Other touch controls
also operate some audio
controls. See ªAudio
Steering Wheel Controlsº
later in this section.
~!(Fan): Press the up arrow on the fan button to
override the automatic fan control and increase the fan
speed in manual mode. Press the down arrow on the fan
button to override the automatic fan control and reduce
the fan speed in manual mode.
~TEMP! (Temperature): Press either arrow on the
TEMP button once to display your current temperature
setting in the digital display. Press the up arrow on the
TEMP button again to provide a warmer temperature
setting or press the down arrow on the TEMP button
again to provide a cooler temperature setting.
Audio Systems
Your audio system has been designed to operate easily
and give years of listening pleasure. You will get the
most enjoyment out of it if you acquaint yourself with it
first. Find out what your audio system can do and how
to operate all of its controls to be sure you're getting the
most out of the advanced engineering that went into it.
Your vehicle has a feature called Retained Accessory
Power (RAP). With RAP, you can play your audio
system even after the ignition is turned off. See
ªRetained Accessory Power (RAP)º in the Index.
Setting the Clock
Press and hold HR until the correct hour appears. The
letters AM or PM will appear on the display. Then, press
and hold MN until the correct minute appears. The clock
may be set with the ignition on or off.
To set the clock to the time of an FM station
broadcasting Radio Data System (RDS) information,
press and hold HR and MN at the same time until
UPDATED appears on the display. If the time is not
available from the station, NO UPDATE will appear on
the display instead.
ProCarManuals.com

3-11 AM-FM Stereo with Cassette Tape and
Compact Disc Player with Programmable
Equalization and Radio Data System (RDS)
Standard Radio -- Bose
Not Shown
Playing the Radio
POWER: Press this knob to turn the system on and off.
VOLUME: Turn the knob clockwise to increase
volume. Turn it counterclockwise to decrease volume.SCV (Speed
-Compensated Volume): With SCV, your
audio system adjusts automatically to make up for road
and wind noise as you drive. Set the volume at the
desired level. Press this button to select MIN, MED or
MAX. Each higher choice allows for more volume
compensation at faster vehicle speeds. Then, as you
drive, SCV automatically increases the volume, as
necessary, to overcome noise at any speed. The volume
level should always sound the same to you as you drive.
If you don't want to use SCV, select OFF.
Finding a Station
BAND: Press this button to switch between AM, FM1
and FM2. The display shows your selection.
TUNE: Turn this knob to select radio stations.
SEEK : Press the right or left arrow to go to the
next or previous station and stay there. The radio will
seek to stations with a strong signal only. The sound will
mute while seeking.
SCAN : Press and hold either arrow for two
seconds until SC appears on the display and you hear
a beep. The radio will go to a station, play for a few
seconds, then go on to the next station. Press either
SCAN arrow again to stop scanning. The radio will
scan to stations with a strong signal only. The sound will
mute while scanning.
ProCarManuals.com

3-12
To scan preset stations, press and hold either SCAN
arrow for more than four seconds, PRESET SCAN will
appear on the display. You will hear a double beep and
the P will blink with the preset number. The radio will
go to the first preset station stored on your pushbuttons,
play for a few seconds, then go on to the next preset
station. Press either SCAN arrow again to stop scanning
presets. The radio will scan preset stations with a strong
signal only. The sound will mute while scanning.
Setting Preset Stations
The six numbered pushbuttons let you return to your
favorite stations. You can set up to 18 stations (six AM,
six FM1 and six FM2), by performing the following steps:
1. Turn the radio on.
2. Press BAND to select the band.
3. Tune in the desired station.
4. Press AUTO EQ to select the equalization that best
suits the type of station selected.
5. Press and hold one of the six numbered pushbuttons
until you hear a beep. Whenever you press that
numbered pushbutton, the station you set will return
and the equalization that you selected will also be
automatically selected for that pushbutton.
6. Repeat the steps for each pushbutton.Setting the Tone (Bass/Treble)
AUDIO: Press the AUDIO button until BASS, MID
or TREB appears on the display. Press the knob above
the AUDIO button to extend it, then turn the knob to
increase or decrease. When you use this knob, the
radio's tone setting will switch to manual. If a station is
weak or noisy, you may want to decrease the treble.
Press and hold the AUDIO button for at least two
seconds to return all tone settings, including balance
and fade to flat.
AUTO EQ (Automatic Equalizer): This feature
allows you to choose preset bass, midrange and treble
equalization settings designed for country, jazz, talk,
pop, rock and classical program types.
The program type last chosen will appear on the display
when you first press AUTO EQ. Each time you press
this button, another program type will appear on the
display and AUTO EQ will switch to one of the preset
program types.
To return to the manual mode, press the AUTO EQ
button until MANUAL appears on the display. Then you
will be able to manually adjust the bass, midrange and
treble using the AUDIO button.
ProCarManuals.com

3-13
If your vehicle has the Bose radio, the AUTO EQ button
will work the same, except the radio will display EQ1
through EQ6 as the choices instead of displaying the
equalization setting names. These settings can be used
while listening to the radio or the CD player.
The radio saves separate AUTO EQ settings for each
preset and source.
Adjusting the Speakers (Balance/Fade)
AUDIO: To adjust the balance between the right
and left speakers, press the AUDIO button until BAL
appears on the display. Press the knob above the AUDIO
button to extend it, then turn the knob to adjust the
sound to the left or right speakers. The middle position
balances the sound between the speakers.
To adjust the fade between the front and rear speakers,
press the AUDIO button until FAD appears on the
display. Press the knob above the AUDIO button to
extend it, then turn the knob to adjust the sound to the
front or rear speakers. The middle position balances the
sound between the speakers.
Press and hold the AUDIO button for at least two
seconds to return all tone settings, including bass
and treble to flat.Using RDS
Your audio system is equipped with a Radio Data
System (RDS). With RDS, the radio can do
the following:

Seek only to stations with the types of programs you
want to listen to,

seek to stations with traffic announcements,

receive announcements concerning local and
national emergencies, and

receive and display messages from radio stations.
RDS features are only available on FM stations that
broadcast RDS information. The RDS features on your
radio rely on receiving specific RDS information from
these stations. These features will only work when the
RDS information is available. In rare cases, a radio
station may broadcast incorrect information that will
cause the radio features to work improperly. If this
happens, contact the radio station.
When you are tuned to an RDS station, the station
name will appear on the display, instead of the
frequency. Most RDS stations provide their station
name, the time of day and a Program Type (PTY)
for their current programming.
ProCarManuals.com

3-14
Finding a PTY Preset Station
To find a PTY preset station, perform the following steps:
1. Press the P
-TYPE button to turn on PTY select. PTY
will be displayed and the light next to the button will
turn on. The last selected PTY will appear on the
display for five seconds.
2. Turn the P
-TYPE knob clockwise or
counterclockwise to select the PTY you want to
listen to. The list is alphabetical. If you select ANY
TYPE your radio will seek to the first PTY available.
3. Press the right SEEK arrow to find radio stations for
that PTY. The radio will seek to the first RDS
broadcaster of the selected program type. If the radio
cannot find the desired program type, NOT FOUND
will appear on the display and the radio will return to
the last station you were listening to. If both P
-TYPE
and TRAF are on, the radio will search for stations
with traffic announcements and the selected PTY.To use the P
-TYPE interrupt feature, press and hold the
P
-TYPE button until you hear a beep on the PTY you
want to interrupt on. An asterisk will appear next to the
PTY name (for example CLASSICAL*). When you are
listening to a cassette or compact disc, the last selected
RDS FM station will interrupt play if that selected PTY
format is broadcast.
BAND (Alternate Frequency): Alternate frequency
allows the radio to switch to a stronger station with the
same program type. Press and hold BAND for two
seconds to turn alternate frequency on. AF ON will
appear on the display. The radio may switch to stronger
stations. Press and hold BAND again for two seconds to
turn alternate frequency off. AF OFF will appear on the
display. The radio will not switch to other stations. When
you turn the ignition off and then on again, the alternate
frequency feature will automatically be turned on.
SEEK : Press the right arrow to go to a station with
the last selected PTY; TYPE and the last selected PTY
will appear on the display, if it is not already showing.
Press SEEK a second time to seek. If a station with the
selected PTY is not found, the radio will return to the
original station and display NONE.
ProCarManuals.com