Oldsmobile Cutlass 1998 s Owners Manual

Running Your Engine While
You’re Parked
It’s better not to park with the engine running. But if you
ever have to, here are
some things to know.
Idling the engine with the climate control
system off could allow dangerous exhaust into
your vehicle (see the earlier Caution under
“Engine Exhaust”).
Also, idling in a closed-in place can let deadly
carbon monoxide (CO) into your vehicle even
if
the fan switch is at the highest setting. One place
this can happen is
a garage. Exhaust -- with
CO
-- can come in easily. NEVER park in a
garage with the engine running.
Another closed-in place can be a blizzard.
(See “Blizzard”
in the Index.)
Follow the proper steps to be sure your vehicle won’t
ove. See “Shifting Into
PARK (P)” in the Index.
JI you are parking on a hill and if you’re pulling a
trailer, also see “Towing a Trailer’’ in the Index.
2-27 ,

Windows
Manual Windows
On a vehicle with manual windows, use the window
crank to open and close each window.
Power Windows (If Equipped)
The power window switches are located on the armrest
of the driver’s door.
In addition, each passenger door has
a switch for its own window.
Auto-Down switch
The driver’s window switch has an auto-down feature.
This switch is labeled AUTO. Push the switch back
partway, and the driver’s window will open a small
amount.
If the switch is pushed all the way back, the
window will go all the way down.
To stop the window while it
is lowering, move the
switch forward. To raise the window, move and hold the
switch forward.
Lock Out Switch
The driver’s power window controls also include a lock
out switch. Press
LOCK OUT to stop front and reat
passengers from using their window switches. The
driver can still control all the windows with the lock
on. Press the LOCK OUT button again for normal
window operation.
P .. ,.
Horn
You can sound the horn by pressing the horn symbol on
your steering wheel.
2-28

I Tilt Wheel
2-29

Turn and Lane Change Signals
The turn signal has two upward (for right) and two
downward (for left) positions. These positions allow you
to signal a turn or a lane change.
To signal a
turn, move the lever all the way up or down.
When the
turn is finished, the lever will return automatically.
An arrow on the instrument
panel will flash in the
direction of the turn or
lane change.
To signal a lane change, just raise or lower the lever
until the arrow starts to flash. Hold it there until you
complete your lane change. The lever will return by
itself when you release it.
A warning chime signal will come on if you have left
your turn signal on for more than
3/4 mile (1 km).
As you signal a turn or a lane change, if the arrow
flashes rapidly, a signal bulb may be burned out and
other drivers won’t see your turn signal. If
a bulb is burned out, replace it to help avoid an
accident.
If the arrow doesn’t go on at all when you
signal a
turn, check for burned-out bulbs and then check
the fuse (see “Fuses and Circuit Breakers” in the Index).
Headlamp HighLow Beam
To change the headlamps .
from low beam to high
beam, push forward on the
turn signal/multifunction
lever.
I I
To change the headlamps fkom high beam to low beam,
pull the
turn signal lever backward. When the high
beams
are on, a light on the instrument panel will also
be on.
Flash to Pass
This feature lets you use your high-beam headlamps to
signal a driver in front of
you that you want to pass.
To use it, pull the turn signal/multifunction lever toward
you until the high-beam headlamps come on, then
release the lever to turn them
off.

Windshield Wipers
You control the windshield wipers by moving the stalk
with the wiper symbol
on it up or down.
For a single wiper cycle, push the stalk down to
MIST, then release it. For more cycles, hold the stalk
down longer.
For steady wiping at low speed, move the stalk up to the
LO position. For high-speed wiping, move the stalk up
hrther, to
HI. To stop the wipers, move the stalk to OFF.
You can set the wiper speed for a long or short delay between
wipes.
This can be very useful in light rain or snow.
2-31

Heavy snow or ice can overload your wipex motor. A
circuit breaker will stop ,the motor until it c.o.01~. Clear
away snow or ice to prevent an overload.
Windshield Washer In freezing weather, don't use your washer until
the windshield
is warmed. Otherwise the washer
fluid can form ice on the windshield, bl'ocking
When you release the button, the washers will stop,
but the wipers will continue to wipe for about three
times or will either stop or will resume the speed you
were using before.
To wash your windshield, push in the button at the end
of the stalk until the washers begin.
2-32

Cruise Control
With cruise control, you can maintain a speed of about
25 mph (40 lun/h) or more without keeping your
foot
on the accelerator. This can really help on long
trips. Cruise control does not work at speeds below
25 mph (40 km/h).
When you apply your brake, the cruise control shuts off.
e
e
Cruise control can be dangerous where you
can’t drive safely at a steady speed.
So,
don’t use your cruise control on winding
roads or in heavy traffk.
Cruise control can be dangerous
on
slippery roads. On such. roads, fast changes
in tire traction can cause needless wheel
spinning, and you could lose control. Don’t
use cruise control on slippery roads.
2-33

Setting Cruise Control
If you leave your cruise control switch on when
you’re not using
cruise, you might hit a button
and go into cruise when you don’t want to. You
could be startled and even lose control. Keep the
cruise control switch
off until you want to use it.
The cruise control buttons are located on the center of
the steering wheel.
1. Press the cruise control ON/OFF button. Resuming a Set Speed
Suppose you
set your cruise control at a desired speed
and then you apply the brake.
This, of course, shuts off
the cruise control. But you don’t need to reset it. Once
you’re going about
25 mph (40 km/h) or more, you can
press the cruise control ACCEL
RESUME button for
about half a second.
You’ll go right back up to your chosen speed and
stay there.
If you press the ACCEL RESUME button longer than
half a second, the vehicle will keep going faster until
you release the switch or apply the brake.
So unless you
want to go faster, don’t hold down the
ACCEL
RESUME button.
2. Get up to the speed you want.
3. Press the SET DECEL button and release it.
4. Take your foot off the accelerator pedal.
2-34

2-35

Exterior Lamps
Rotate the turn signal lever end cap up one position to
turn on:
Parking Lamps
Side Marker Lamps
Taillamps
0 License Plate Lamps
Instrument Panel Lights Rotate the
turn signal lever end cap up two positions to
turn on:
Headlamps
0 Parking Lamps
Sidemarker Lamps
License Plate Lamps
Instrument Panel Lights
Rotate the switch to
OFF to turn all of the lamps off.
Lamps On Reminder
If you open the driver’s door and turn off the
ignition while leaving the lamps on, you
will hear a
warning chime.
2-36