tailgate OPEL ANTARA 2009 Owner's Manual

Driving and operation160
Attach the pedal crank by rotating the
attachment screw on the pedal crank
mount.Place the wheel recesses such that the
bicycle is more or less horizontal. Here, the
distance between the pedals and the
tailgate should be at least 5 cm. Setting the
wheel recesses - see page 158.
Both bicycle tyres must be in the wheel
recesses. In order to prevent damage,
neither the pedal bearing housing on the
bicycle nor the pedal crank should be
touching the pedal crank recess.Align the bicycle in the longitudinal
direction of the vehicle:
Slightly loosen the pedal bearing mount -
see page 157, Fig. 14629 S.
Place the bicycle upright using the rotary
lever on the pedal crank recess -
see page 157, Fig. 14629 S or page 158,
Fig. 14630 S.
If the two bicycles obstruct one another,
the relative positions of the bicycles can be
adapted by adjusting the wheel recesses
and the rotary lever on the pedal crank
recess until the bicycles no longer touch
one another. Make sure there is sufficient
clearance from the vehicle.

Driving and operation164
Pull up license plate holder and fold down
into horizontal position.Open the tailgate.
Raise the release lever
and push the system
into the bumper until it engages.
Ensure release lever returns to original
position.
Towing equipment 3
If the vehicle is not equipped with a trailer
hitch, we recommend having this
retrofitted by a workshop, who will advise
you on any possible towed load increases.
The workshop has instructions on how to
install the trailer hitch and making any
changes to the vehicle that are needed
that affect the coolin g system, heat shields
or other equipment.
Mounting dimensions of towing equipment
- see page 227.
9 Warning
If the system cannot be correctly
engaged, please contact a workshop for
assistance.
9 Warning
The coupling ball bar is to be removed
when not towing.

Self-help, vehicle care176
Screw the rear towing eye attachment anti-
clockwise until it is firmly in place.
Drive off slowly and avoid jerky
movements. Impermissible tractive forces
could damage the vehicles.
To prevent damage, do not take up slack
in the tow rope too quickly.
After towing, unscrew the rear towing eye
attachment clockwise to remove, and
reinstall the cover.
Jack and vehicle tools
The jack and vehicle tools have been
specially developed for your vehicle and
must only be used on that vehicle. Only use
jack for changing wheels.
The jack and vehicle tools are located in
the luggage compartment below the floor
cover. To remove the jack and vehicle tools, open
the tailgate. Push both levers on the floor
cover towards the handle and pull up the
floor cover by the handle.
Hang the hook to the upper part of the
tailgate opening (see page 63, Fig.
S 13419).
Remove wing bolt from the jack by rotating
it anti-clockwise and remove the jack and
wheel wrench bag.
Remove straps holding the bag containing
the wheel wrench. Remove wheel wrench
from the bag.
9 Warning
Never lift vehicle using the towing eye.
9 Warning
In a sudden stop or a collision, loose items
can be thrown around inside the vehicle,
causing personal injury and damage to
the interior.
Secure the jack and vehicle tools away
properly under the floor cover in the
luggage compartment.

Self-help, vehicle care177
Warning triangle
¨ 3 ,
First aid kit
+3
Your first aid kit and warning triangle can
be accommodated below the floor cover in
the luggage compartment.
Temporary spare wheel
The temporary spare wheel is located in
the luggage compartment below the floor
cover and is secured with a screw-in
retainer.
Push both levers on the floor cover towards
the handle and pull up floor cover by the
handle (see page 176, Fig. S 13700). Hang
the hook to the upper part of the tailgate
opening (see page 63, Fig. S 13419).
Remove the retainer by rotating it anti-
clockwise, and remove spare wheel from
the spare wheel well. General information
If you use winter tyres
3, the spare wheel
may still be fitted with a summer tyre.
If you use the spare wheel when it is fitted
with a summer tyre, the vehicle's
driveability may be affected, especially on
slippery road surfaces.
Obtain a replacement for the faulty tyre as
soon as possible, and have the wheel
balanced and fitted to the vehicle.

Self-help, vehicle care188
Front fog lamps
1. Remove 2 screws from panel on underside of vehicle below front fog
lamps and remove panel.
2. Disconnect harness connector from bulb holder and rotate bulb holder anti-
clockwise.
3. Remove bulb holder from lamp assembly, rotate bulb anti-clockwise and
remove from bulb holder.
4. Install new bulb in to bulb holder and
rotate it clockwise.
5. Reinstall bulb holder in lamp assembly
and reconnect harness connector.
6. Reinstall panel to underside of vehicle using 2 screws removed earlier. Side repeater lamps
1. Using a suitable screwdriver, pry lamp
assembly away from wing.
2. Rotate bulb holder anti-clockwise.
3. Remove bulb from lamp assembly by pulling bulb straight out of bulb holder.
4. Install new bulb into bulb holder by pressing it in and rotating the bulb
holder clockwise.
5. Push lamp assembly back into aperture. Rear brake, tail, turn signal, reverse lamps
and fog tail lamp
1. Open the tailgate and remove 2 screws
and lamp assembly.
2. Remove bulb holder by rotating it anti-clockwise.
3. Remove bulb from bulb holder by pressing the bulb in and rotating it anti-
clockwise.
4. Install new bulb into bulb holder.
5. Reinstall bulb holder into lamp assembly. Rotate bulb holder clockwise and ensure
it is secure.

Self-help, vehicle care189
6. Replace lamp assembly by guiding lugs on lamp assembly into their holes (see
black arrows in illustration).
7. Replace 2 screws removed earlier and close the tailgate. License plate lamps
1. Remove 4 screws (arrowed) and remove
lamp covers.
2. Remove bulb holder from lamp assembly by rotating it anti-clockwise.
3. Pull bulb straight out of bulb holder.
4. Install new bulb.
5. Reinstall bulb holder into lamp assembly, rotate bulb holder clockwise and ensure
it is secure.
6. Replace lamp covers using 4 screws removed earlier. Front reading lamps
1. Using a suitable screwdriver, pry lamp
lens away from roof lining.
2. Remove bulb.
3. Install new bulb.
4. Reinstall lamp lens in roof lining.

Self-help, vehicle care202
Vehicle care aids 3
Vehicle wash:
z Car Shampoo
z Sponges
z Chamois Leather
z Wheel Cleaners
z Engine Cleaners
z Glass Cleaners
Exterior care:
z Touch-up Applicator
z Spray and Touch-up Paint
z Car Polishes/Colour Restorers
z Car Waxes/Sealers
z Alloy Wheel Cleaner
z Alloy Wheel Preserver
z Metallic Paintwork Wax
z Rust Preventative
z Lubricant Sprays
z Lock Cylinder Grease
z De-icer Sprays
z Tar Removal Spray
z Insect Remover
z Window Cleaning Spray
z Cleaning Solvent and Antifreeze
Interior care:
z Interior/Upholstery Cleaner Washing
The paintwork of your vehicle is exposed to
environmental influences, e.g. continuous
changes in weather conditions, industrial
waste gases and dust or thawing salts, so
wash and wax your vehicle regularly. When
using automatic car washes, select a
program which includes waxing.
Bird droppings, dead insects, resin, pollen
and the like should be cleaned off
immediately, as they contain aggressive
constituents which can cause paint
damage.
If using a car wash, comply with the
pertinent instructions of the car wash
manufacturer. The windscreen wipers and
tailgate wipers must be switched off –
see pages 92, 93. Remove detachable rod
antenna by unscrewing it.
Do not use high-pressure jet cleaners.
If you wash your vehicle by hand, make
sure that the insides of the wings are also
thoroughly rinsed out. Do not use
household dishwashing liquid, to avoid
removing wax from the paintwork.
Clean edges and folds on opened doors
and flaps as well as the areas they cover.
Thoroughly rinse off and leather-off the
vehicle. Rinse leather frequently. Use
separate leathers for paint and window
surfaces; remnants of wax on the windows
will impair vision.
Also wash aluminium trim parts, avoiding
the use of abrasive materials such as
automotive or chrome polish, steam or
caustic soap. Washing with water is
normally sufficient.
Observe national regulations.

208 Service, maintenance
Service operations by year 1)
km ( x 1000)1)
miles ( x 1000)1)
1)Whichever occurs first.
⊕ Additional operations.
o Under extreme operating conditions and if required by country-specific conditions, the intervals are reduced.
15
10 1
30
20 45
30 2
60
40 75
50 3
90
60
⊕o Diesel fuel filter: drain water
(If relative humidity is high an
d/or fuel is of lower quality) Annually
Fuel filter: replace and drain water - diesel (g rade EN 590) Every 2 years/60 000 km/40 000 miles
Parking brake: check and adjust
Wheel mounting and suspension front an d rear, brake lines, brake pressure
hoses, fuel lines and exhaust system: visual check xxx
Corrosion protection: check and record in Service and Warranty Booklet Annually
Front and rear wheel br akes: check visually xxx
o
⊕Annual service check if annual mileage exceeds 20 000 km Annually
Engine, transmission, PTO, rear differential, A/C compressor: check for leaks xxx
Steering system boots, track rods , final drive: visual check xxx
Track rod end and supporting ball joint: check xxx
⊕Brake and clutch fluid: change Every 2 years
Wheel fastening: loosen and tighten to torque
Tyre condition and pressures: check, correct xxx
⊕Annual service check if annual
mileage exceeds 20 000 km Annually
First aid kit, tyre repair kit and lash ing eyes: visual check Every 2 years
Headlamp aiming: check, adjust x x x
Door hinges, door stop, lock cylinder, lock striker, bonnet catch, tailgate
hinges and check links: lubricate xxx
Test drive, final check
Service interval display and oil life monitor: reset - if applicable xxx

210 Service, maintenance
Service operations by year 1)
km ( x 1000)1)
miles ( x 1000)1)
1)Whichever occurs first.
⊕ Additional operations.
o Under extreme operating conditions and if required by country-specific conditions, the intervals are reduced.
15
10 1
30
20 45
30 2
60
40 75
50 3
90
60
⊕o Diesel fuel filter: drain water
(If relative humidity is high an
d/or fuel is of lower quality) Annually
Fuel filter: replace and drain water - diesel (g rade EN 590) Every 2 years/60 000 km/40 000 miles
Parking brake: check and adjust
Wheel mounting and suspension front an d rear, brake lines, brake pressure
hoses, fuel lines and exhaust system: visual check Every 2 years/60 000 km/40 000 miles
Corrosion protection: check and record in Service and Warranty Booklet Annually
Front and rear wheel brakes: check visually Every 2 years/60 000 km/40 000 miles
o
⊕Annual service check if annual mileage exceeds 20 000 km Annually
o
⊕Automatic transmission oil: change Every 4 years/60 000 km/40 000 miles
Engine, transmission, A/C compressor: check for leaks Annually
Steering system boots, track rods, final drive: visual check Annually
Track rod end and supporting ball joint: check Annually
⊕Brake and clutch fluid: change Every 2 years
Wheel fastening: loosen and tighten to torque
Tyre condition and pressures: check, correct Every 2 years/60 000 km/40 000 miles
⊕Annual service check if annual
mileage exceeds 20 000 km Annually
First aid kit, tyre repair kit and lash ing eyes: visual check Every 2 years
Headlamp aiming: check, adjust Every 2 years/60 000 km/40 000 miles
Door hinges, door stop, lock cylinder, lock striker, bonnet catch, tailgate
hinges and check links: lubricate Every 2 years/60 000 km/40 000 miles
Test drive, final check
Service interval display and oil life monitor: reset - if applicable xxxxxx

212 Service, maintenance
Service operations by month 1)
km ( x 1000)1)
miles ( x 1000)1)
1)Whichever occurs first.
⊕ Additional operations.
o Under extreme operating conditions and if required by country-specific conditions, the intervals are reduced.
6
10
6.5 12
20
1318
30
2024
40
26.5 30
50
3336
60
40
Parking brake: check and adjust
Wheel mounting and suspension front an d rear, brake lines, brake pressure
hoses, fuel lines and exhaust system: visual check xxx
Corrosion protection: check and record in Service and Warranty Booklet Annually
Front and rear wheel br akes: check visually x x x
Engine, transmission, PTO, rear differential, A/C compressor: check for leaks xxx
Steering system boots, track rods , final drive: visual check xxx
Track rod end and supporting ball joint: check xxx
⊕Brake and clutch fluid: change Every 2 years
Wheel fastening: loosen and tighten to torque
Tyre condition and pressures: check, correct xxx
First aid kit, tyre repair kit and lash ing eyes: visual check Every 2 years
Headlamp aiming: check, adjust xxx
Door hinges, door stop, lock cylinder, lock striker, bonnet catch, tailgate
hinges and check links: lubricate xxx
Test drive, final check
Service interval display and oil life monitor: reset - if applicable xxx