battery OPEL FRONTERA 1998 Workshop Manual

8H–2SECURITY AND LOCKS
Service Precaution
WARNING: IF SO EQUIPPED WITH A
SUPPLEMENTAL RESTRAINT SYSTEM (SRS),
REFER TO THE SRS COMPONENT AND WIRING
LOCATION VIEW IN ORDER TO DETERMINE
WHETHER YOU ARE PERFORMING SERVICE ON OR
NEAR THE SRS COMPONENTS OR THE SRS
WIRING. WHEN YOU ARE PERFORMING SERVICE
ON OR NEAR THE SRS COMPONENTS OR THE SRS
WIRING, REFER TO THE SRS SERVICE
INFORMATION. FAILURE TO FOLLOW WARNINGS
COULD RESULT IN POSSIBLE AIR BAG
DEPLOYMENT, PERSONAL INJURY, OR
OTHERWISE UNNEEDED SRS SYSTEM REPAIRS.CAUTION: Always use the correct fastener in the
proper location. When you replace a fastener, use
ONLY the exact part number for that application.
ISUZU will call out those fasteners that require a
replacement after removal. ISUZU will also call out
the fasteners that require thread lockers or thread
sealant. UNLESS OTHERWISE SPECIFIED, do not
use supplemental coatings (Paints, greases, or other
corrosion inhibitors) on threaded fasteners or
fastener joint interfaces. Generally, such coatings
adversely affect the fastener torque and the joint
clamping force, and may damage the fastener. When
you install fasteners, use the correct tightening
sequence and specifications. Following these
instructions can help you avoid damage to parts and
systems.
Front Door Lock Assembly
Front Door Lock Assembly and Associated Parts
632RS003
Legend
(1) Door Trim Panel
(2) Waterproof Sheet
(3) To Outside Handle(4) Rear Guide Rail
(5) Door Lock Assembly
(6) Door Lock Switch Connector (W/Power Door
Lock)
Removal
1. Disconnect the battery ground cable.
2. Remove the door trim panel.3. Remove the waterproof sheet.
Refer to the Window Regulator removal procedure in
Body Structure section.

8H–4SECURITY AND LOCKS
Front Outside Handle and Door Lock Cylinder
Front Outside Handle, Door Lock Cylinder and Associated Parts
632RS006
Legend
(1) Door Trim Panel
(2) Waterproof Sheet
(3) Outside Handle(4) Door Lock Cylinder
(5) Clip
(6) Key Switch (W/Anti-Theft)
Removal
1. Disconnect the battery ground cable.
2. Remove the door trim panel.
3. Remove the waterproof sheet.
Refer to the Window Regulator removal procedure in
Body Structure section.

SECURITY AND LOCKS8H–7
Rear Door Lock Assembly
Rear Door Lock Assembly and Associated Parts
652RW004
Legend
(1) Door Trim Panel(2) Waterproof Sheet
(3) Door Lock Assembly
Removal
1. Disconnect the battery ground cable.
2. Remove the door trim panel.
3. Remove the waterproof sheet.
Refer to the Window Regulator removal procedure in
Body Structure section.

SECURITY AND LOCKS8H–9
Rear Outside Handle
Rear Outside Handle and Associated Parts
652RW003
Legend
(1) Door Trim Panel(2) Waterproof Sheet
(3) Outside Handle
Removal
1. Disconnect the battery ground cable.
2. Remove the door trim panel.
3. Remove the waterproof sheet.
Refer to the Window Regulator removal procedure in
Body Structure section.
4. Disconnect the locking link (arrow mark position) and
remove three fixing bolts to remove the outside
handle.
652RS003

8H–10SECURITY AND LOCKS
Installation
To install, follow the removal steps in the reverse order,
noting the following points.1. Tighten the outside handle fixing bolts to the specified
torque.
Torque: 9 Nꞏm (0.9kgꞏm/78 lb in)
2. Check that the outside handle operates smoothly.
Rear Door Inside Lock Knob Link
Removal
1. Disconnect the battery ground cable.
2. Remove the door trim panel(3).
3. Remove the waterproof sheet(2).
Refer to the Window Regulator removal procedure in
Body Structure section.
4. Remove the fixing screw(4) and disconnect the
locking link at the door lock assembly to remove the
rear door inside lock knob link(1).
655RW009
Installation
To install, follow the removal steps in the reverse order.

SECURITY AND LOCKS8H–11
Door Inside Lock Knob
Removal
1. Disconnect the battery ground cable.
2. Remove the door trim panel(1).
Refer to the Door Trim Panel removal procedure in
Exterior/Interior Trim section.
3. Turn the door inside lock knob counterclockwise and
then remove the door inside lock knob (2).
632RS011
Installation
To install, follow the removal steps in the reverse order.
Door Inside Handle
Removal and Installation
Refer to the Door Trim Panel removal and installation
procedures in Exterior/Interior Trim section.
635RS008

8H–12SECURITY AND LOCKS
Tailgate Lock Assembly (LH)
Tailgate Lock Assembly (LH) and
Associated Parts
684RW008
Legend
(1) Tailgate Trim Panel(LH)(2) Waterproof Sheet
(3) Tailgate Lock Assembly
Removal
1. Disconnect the battery ground cable.
2. Remove the tailgate trim panel (LH).
Refer to the Tailgate Trim Panel (LH) removal
procedure in Exterior/Interior Trim section.
3. Taking notice of the tailgate harness, peel the
waterproof sheet off the tailgate panel carefully and
then remove the waterproof sheet.
684RS005

8H–14SECURITY AND LOCKS
Tailgate Lock Assembly (RH)
Tailgate Lock Assembly (RH) and Associated Parts
684RW006
Legend
(1) Tailgate Trim Panel (RH)
(2) Waterproof Sheet
(3) Tailgate Lock Seal(4) Clip
(5) Screw
(6) Tailgate Lock Assembly (RH)
Removal
1. Disconnect the battery ground cable.
2. Remove the tailgate trim panel (RH).
Refer to the Tailgate Trim Panel (RH) removal
procedure in Exterior/Interior Trim section.
3. Peel the waterproof sheet off the tailgate panel
carefully and then remove the waterproof sheet.
4. Remove three fixing bolts and then remove the
tailgate lock assembly (RH).
683RW009

SECURITY AND LOCKS8H–15
5. Remove the tailgate lock seal fixing clip(1) and then
remove the tailgate lock seal(2).
683RW008
Installation
To install, follow the removal steps in the reverse order,
noting the following points.
1. Apply chassis grease to the lock assembly and striker
moving surface.
2. Tighten the tailgate lock assembly fixing bolts to the
specified torque.
Torque: 11 Nꞏm (1.1kgꞏm/95 lb in)
3. Check that the tailgate lock operates correctly after
installing it.
Tailgate Inside Lock Knob
Removal
1. Disconnect the battery ground cable.
2. Remove the tailgate trim panel (LH)(2).
Refer to the Tailgate Trim Panel (LH) removal
procedure in Exterior/Interior Trim section.
3. Take care of cushion to turn the lock knob
counterclockwise and then remove the tailgate inside
lock knob(1).
683RW014
Installation
To install, follow the removal steps in the reverse order.

SECURITY AND LOCKS8H–17
Tailgate Outside Handle and/or Tailgate Lock Cylinder
Tailgate Outside Handle and/or Tailgate Lock Cylinder and Associated Parts
684RW007
Legend
(1) Tailgate Trim Panel (LH)
(2) Waterproof Sheet
(3) Grommet(4) Tailgate Lock Cylinder
(5) Tailgate Outside Handle
(6) Key Switch (W/Anti–Theft)
Removal
1. Disconnect the battery ground cable.
2. Remove the tailgate trim panel.
3. Remove the waterproof sheet.
Refer to the Tailgate Lock Assembly (LH) in this
section.
4. Remove the grommet.