key PEUGEOT 108 2016 User Guide

36
108_en_Chap02_ouvertures_ed01-2016
emergency procedure
unlocking
F Insert the integral key into the driver's door lock barrel and turn it towards the front of
the vehicle to unlock the vehicle.
Locking
F Insert the integral key into the driver's door lock barrel and turn it towards the rear of
the vehicle to lock the vehicle.
th

e integral key is used to lock and unlock the
vehicle when the electronic key cannot operate
and in the event of a fault with the Keyless
en

try and Starting system:
-

c

ell battery discharged, vehicle battery
discharged or disconnected, ...
-
v
ehicle located in an area with strong
electromagnetic signals.
F

P

ress and hold the latch 1 to extract the
integral key 2 .
Saving the electronic key
battery
to preserve the battery, it is possible to prevent
the electronic key working (no reception of
radio waves).
When this function is activated, the "Keyless
en

try and Starting" system is inoperative.
to r

eactivate the electronic key, press one of
the buttons (open or closed padlock). F

P
ress on the open padlock twice,
while pressing on and holding
the closed padlock.
Check that the indicator lamp in the electronic
key flashes 4 times.
Access

37
108_en_Chap02_ouvertures_ed01-2016
Changing the battery of
the electronic key
Battery ref.: CR2032 / 3 volts.When replacement of the battery is
needed, this warning lamp comes on
in the instrument panel.
F
u
n
clip the cover using a small screwdriver
at the cutout.
F

R
emove the cover.
F

R
emove the protective battery holder,
pulling it upwards.
F

R
emove the discharged battery from its
housing.
F

F
it the new battery into its housing
observing the original direction of fitment.
F

R
efit the battery holder.
F

C
lip the cover onto the casing.
Lost keys
go to a PeugeOt dealer with the vehicle's registration document, your personal
identification documents and if possible the key code label.
th

e P
e
uge
Ot
dealer will be able to look up the key code and the transponder code
required to order a new key.
Remote control / el ectronic key
these high frequency devices are sensitive systems; do not handle them while in your
pocket as there is a risk of unlocking the vehicle, without you being aware of it.
Do not repeatedly press the buttons of your remote control or electronic key out of range
and out of sight of your vehicle. You run the risk of stopping it from working and the remote
control would have to be reinitialised.
Locking the vehicle
As a safety precaution, never leave children alone in the vehicle, except for a very short
period.
In all cases, it is essential to remove the key from the ignition switch, or take the electronic
key with you when leaving the vehicle.
When purchasing a second-hand vehicle
Have the pairing of all of the keys in your possession checked by a Pe ugeOt dealer, to
ensure that only your keys can be used to open and start the vehicle. Driving with the doors locked may make access to the passenger compartment by the
emergency services more difficult in an emergency.
2
Access

39
108_en_Chap02_ouvertures_ed01-2016
Locking / unlocking and opening the boot
using the keyusing the remote control
F Press the open padlock to unlock
the vehicle and boot.
-

I

nsert the key in the lock barrel and turn
it to the right to unlock and release the
tailgate.


t
he

vehicle remains locked.
-
R
aise the tailgate by the exterior handle to
open it.
F

P

ress the opening button to release the
tailgate.
F

R

aise the tailgate by the exterior handle to
open it.
F

P
ress the closed padlock to
unlock the boot and vehicle.
As soon as you close the tailgate, it locks
again.
2
Access

40
108_en_Chap02_ouvertures_ed01-2016
F With the electronic key on your person, press the boot opening control to unlock
and release the tailgate.


t
h
e vehicle is unlocked as well.
F

R
aise the tailgate by the exterior handle to
open it.
using the Keyless en try
and Starting system
If the vehicle had been previously unlocked by
the front door, it is not necessary to have the
electronic key on your person to use the boot
opening control. F

W
ith the electronic key on your person,
press the button on the boot sill to lock it.

or
L

ock the vehicle by the front doors.
When closing the boot, do not slam shut
the tailgate: guide it down and release it
at the end of its travel.
Boot release
System for mechanical unlocking of the boot
in the event of a battery or central locking
malfunction.
unlocking
F Fold the rear seat backrest to gain access to the lock from inside the boot.
F
u
s
ing a screwdriver protected by a cloth,
remove the 4 fixing clips, then the boot
trim.
F

M
ove the trigger to the right to unlock
the


tailgate.
Access

44
108_en_Chap02_ouvertures_ed01-2016
An aero-acoustic deflector is available to
improve the acoustic comfort of occupants
of the vehicle in certain driving conditions
(high speed), by reducing the turbulence in
the passenger compartment resulting from the
displacement of air.
On opening the roof, the aero-acoustic
deflector is deployed.
On closing the roof, the deflector folds away
automatically.
Aero-acoustic deflector Precautions for use
Never place objects on the roof,
whether open or closed.
Never sit on or place objects on the
transverse roof support when the roof
is open. In the event of prolonged storage of the
vehicle outside, it is recommended that
the roof be protected with a cover.
to a

void damaging the roof, do
not open it under snowy or frosty
conditions.
Never use sharp tools to remove ice or
accumulations of snow on the roof.
to l

imit the creation of folds in the roof
fabric, it is recommended that the roof
not be left open for long periods.
th

e vehicle's air conditioning system
should not be operated while the roof
is open. It is recommended that the roof be
closed when the vehicle is left parked.
ev

en if the roof is closed, it is prudent
not to leave any valuable objects inside
the vehicle.
When you leave the vehicle, switch off
the ignition and remove the key (take
the electronic key with you) to avoid any
unwanted operation of the roof.
Access

71
108_en_Chap04_conduite_ed01-2016
Starting - switching off the engine with the key
1. "L oCK " position.
th e steering column is unlocked.
2.
" AC

C" position.


t
h
e ancillaries (audio system,
12V
socket...) can be used.
3.


"
oN"

position
I

gnition on.
4.
" St

A R
t"
position.


e
n
gine starting.
Ignition switch
For vehicle fitted with a manual gearbox:
F I nsert the key in the ignition switch.
F
t
u
rn the key to position 2 .
F
u
n
lock the steering column, by turning the
wheel slightly.
F

F
ully depress the clutch pedal.
F

P
ut the gear lever into neutral.
F

O
perate the starter by turning the key to
position 4 (S
t

A R
t).
F


O
nce the engine is running, release
t h e


key.


t
h
e key returns automatically to position 3
(
o
N
).
Starting using the key
For vehicles fitted with an etg gearbox:
F I nsert the key in the ignition switch.
F
t
u
rn the key to position 2 .
F
u
n
lock the steering column, by turning the
wheel slightly.
F

P
ress and hold the brake pedal .
F

P
ut the gear selector into position N .
F

O
perate the starter by turning the key to
position 4 (S
t

A R
t).
F


O
nce the engine is running, release
t h e


key.


t
h
e key returns automatically to position 3
(
o
N
)
.
If you use the ancillaries for a prolonged
period (key in position 2 or 3 ), you risk
discharging the battery. Starting your
vehicle will then no longer be possible.
Be aware.
Never leave the engine running in
an enclosed area without adequate
ventilation: internal combustion
engines emit toxic exhaust gases,
such as carbon monoxide. Danger of
intoxication and death. In very severe
winter conditions (temperatures
below

-23°C), it is necessary to allow
the engine to run for 4 minutes before
setting off, in order to ensure the
correct operation and durability of
the mechanical components of your
vehicle, the engine and gearbox.
4
Driving

72
108_en_Chap04_conduite_ed01-2016
If you use the ancillaries for a prolonged
period, the vehicle will automatically
switch to "
oFF" m

ode after about
20


minutes.
Be aware in order to avoid discharging
the battery.
Starting - switching off the engine
with the Keyless e
n
try and Starting
system
Changing the mode of the
vehicle
With the electronic key inside the
vehicle; each press on the " St
A Rt/
StoP " b

utton, with no action on the
pedals, changes the vehicle's mode:
F

F

irst press (" ACC" m o d e).


t
h

e ancillaries (radio, 12V socket...) can be
used.
F

Sec

ond press ("
oN "

m o d e).
I

gnition on.
F
t
h

ird press ("
oFF "

m o d e).
Avoid attaching heavy objects to the
key, which would weigh down on its
blade in the ignition switch and could
cause a malfunction.
F

Imm

obilise the vehicle.
Switching off
F With a manual gearbox: put the gear lever
into neutral.
F

W
ith an etg gearbox: place the selector at
position N .
F
t
u
rn the key towards you to position 2 (ACC) .
F

Press in and turn the key to position 1 (LoC K).F Remove the key from the ignition switch.
F
tu rn the steering until the steering column
locks.
Driving

73
108_en_Chap04_conduite_ed01-2016
Starting using the
electronic key
With the first press on the "St A Rt/
StoP " b
utton, this indicator lamp
flashes slowly in the instrument panel. Depending on the ambient temperature,
each attempt at starting can take up to
around 30 seconds. During this period,
do not press the "
S
t
A
R
t/
S to
P" b

utton
again, or release the clutch pedal or
brake pedal (depending on the type of
gearbox).
After this period, if the engine has not
started, press the " S
t
A
R
t/
S to
P"
b

utton again for another attempt at
starting. If one of the starting conditions is
not met, the "Keyless
e
n
try and
Starting" system indicator lamp flashes
in the instrument panel. In some
circumstances, it is necessary to
turn the steering wheel slightly while
pressing the " S t
A
R
t/
S to
P
" b
utton to
assist unlocking of the steering.
For vehicles fitted with a manual gearbox:
F

W

ith the electronic key inside the vehicle,
put the gear lever into neutral and fully
depress the clutch pedal.th e presence of the electronic key in
the vehicle is essential for switching
on the ignition and starting only. Once
the engine has started, make sure that
the electronic key remains with the
vehicle until the end of the journey:
other wise you would not be able to lock
the


vehicle.
F

P
ress and release the " S
t

A R
t/
StoP " b

utton.
th
is indicator lamp comes on in the
instrument panel. For vehicles fitted with an
etg gearbox:
F
W
ith the electronic key inside the vehicle,
put the gear selector at N and press the
brake pedal.
th
is indicator lamp comes on in the
instrument panel.
F
P
ress and release the "
S
t
A R
t/
StoP " b
utton.
4
Driving

74
108_en_Chap04_conduite_ed01-2016
there is an audible signal when the driver's door
is opened and the vehicle is in "ACC" mode.
If the vehicle is not immobilised, the
engine will not stop.
Switching off using the
electronic key
F Immobilise the vehicle.
F
W ith a manual gearbox: put the gear lever
into neutral.
F

W
ith an etg gearbox: place the gear
selector at N .
F

W
ith the electronic key inside
the vehicle, press the " S
t

A R
t/
StoP " b

utton.
the

engine stops.
th

e steering locks when a door is opened or on
locking the vehicle.
F

P
ress the "S
t
A
R
t/
S to
P" b

utton
again to change to "
oFF " m

ode.
emergency starting
When the electronic key is in the
recognition zone and your vehicle
does not start after pressing the
"S
t
A
R
t/
S to
P" b

utton, this warning
lamp flashes in the instrument panel.
F

W

ith a manual gearbox: put the gear lever
into neutral.
F

W

ith an etg gearbox: place the selector
lever at N . F

P
ut the corner of the electronic key, where
the indicator lamp is located, in contact
with the " S t
A
R
t/
S to
P
" b
utton.


t
h
ere is an audible signal when the
electronic key is recognised; the vehicle
changes to "
oN " m
ode.
F
W
ith a manual gearbox: press the clutch
pedal fully down.
F
W
ith an etg gearbox: press the brake
pedal.
F
C
heck that the "Keyless e
n
try and
Starting" indicator lamp comes on in green
in the instrument panel.
F

P
ress the "S
t
A
R
t/
S to
P" b

utton.


t
h
e engine starts.
If the engine does not start, contact a
P
e

uge
Ot
dealer or a qualified workshop.
Driving

75
108_en_Chap04_conduite_ed01-2016
emergency switch-off
In the event of an emergency only, the engine
can be switched of without conditions. to d o
this, press for more than 2 seconds, or make
a minimum of 3 successive presses on the
" S
t
A
R
t/
S to
P" b

utton.
In this case the steering column locks as soon
as the vehicle stops.
electronic key not
recognised
If the electronic key is no longer in the
recognition zone when driving or when you
(later) request switching off the engine, there is
an audible signal to warn you.
F

P
ress for more than 2 seconds,
or make a minimum of
3
successive presses on the
" S
t
A
R
t/
S to
P" b

utton if you
want to force switching off of the
engine ( note that restarting
will not be possible without
the
key).
electronic engine
immobiliser
this locks the engine management system as
soon as the ignition has been switched off and
therefore prevents starting of the vehicle by
anyone who does not have the key.
th

e ignition key has an electronic chip which
has a special code. When the ignition is
switched on, the code must be recognised for
starting to be possible.
In the event of a malfunction, your vehicle will
not start.
Contact a P
e

uge
Ot
dealer or a qualified
workshop.
Do not make any modifications to the
electronic immobiliser system.
4
Driving