Peugeot 206 P Dag 2010.5 Workshop Manual
Manufacturer: PEUGEOT, Model Year: 2010.5, Model line: 206 P Dag, Model: Peugeot 206 P Dag 2010.5Pages: 119, PDF Size: 4.39 MB
Page 51 of 119
49
CHILD LOCK
On each rear door, this prevents open-
ing of the door from the inside.
Turn control 1 an eighth turn (45 de-
grees) towards the inside of the vehicle
using the ignition key.
Check that the safety lock is engaged
correctly. The control 1 should no longer
be in the vertical position.
LOCKING/UNLOCKING
THE BOOT
Locking and unlocking of the boot is
simultaneous with the doors.
To open the boot, press the control A .
The lighting is controlled by opening
the boot. Tailgate release
System for mechanical unlocking of the
boot in the event of a central locking
malfunction.
Unlocking
Fold back the rear seats to gain
access to the lock from inside the
boot.
Pull the tailgate trim to detach it.
Pull the opening control 1 upwards.
Page 52 of 119
50
FUEL TANK
R e s e r v o i r w h i c h s h o u l d b e r e fi l l e d w i t h
fuel, when the minimum level has been
detected.
Fuel tank capacity: approximately
50 litres. Filling
A l a b e l a f fi x e d t o t h e i n s i d e o f t h e t a n k
reminds you of the type of fuel to be
used depending on your engine.
More than 5 litres of fuel must be add-
ed in order to be registered by the fuel
gauge.
The key cannot be removed from the
l o c k u n t i l t h e fi l l e r c a p i s r e fi t t e d .
Opening the cap may release a vacu-
um, indicated by a noise. This is caused
by the sealing of the fuel system.
T o fi l l t h e t a n k s a f e l y :
the engine
must be
switched off,
i n s e r t t h e k e y i n t h e fi l l e r c a p , t h e n
turn it to the left,
r e m o v e t h e fi l l e r c a p ,
fi l l t h e t a n k , but do not continue
after the 3rd cut-off of the pump ;
this could cause malfunctions.
W h e n y o u h a v e fi l l e d t h e t a n k :
r e fi t t h e fi l l e r c a p ,
turn the key to the right, then remove
i t f r o m t h e fi l l e r c a p .
Page 53 of 119
DIESEL
51
Quality of the fuel used for
petrol engines
The petrol engines are perfectly com-
patible with E10 type petrol biofuels
(containing 10 % ethanol), conforming
to European standards EN 228 and
EN 15376.
E85 type fuels (containing up to 85 %
e t h a n o l ) a r e r e s e r v e d e x c l u s i v e l y f o r
vehicles marketed for the use of this
t y p e o f f u e l ( B i o F l e x v e h i c l e s ) . T h e
quality of the ethanol must comply with
European standard EN 15293.
For Brazil only, special vehicles are
marketed to run on fuels containing up
to 100 % ethanol (E100 type). Quality of the fuel used for
Diesel engines
The Diesel engines are perfectly com-
patible with biofuels which conform to
current and future European standards
(Diesel fuel which complies with stan-
d a r d E N 5 9 0 m i x e d w i t h a b i o f u e l w h i c h
complies with standard EN 14214)
available at the pumps (containing up
to 7 % Fatty Acid Methyl Ester).
The B30 biofuel can be used in cer-
tain Diesel engines; however, this use
is subject to strict application of the
special servicing conditions. Consult a
PEUGEOT dealer.
The use of any other type of (bio)fuel
(vegetable or animal oils, pure or dilut-
ed, domestic fuel...) is strictly prohibited
(risk of damage to the engine and fuel
system).
Page 54 of 119
i
52
LIGHTING CONTROL STALK
System for selecting and controlling the
various front and rear lamps providing
the vehicle's lighting. Manual controls
Lighting off
Sidelamps
Dipped/Main beam headlamps
Lighting
The various front and rear lamps of the
vehicle are designed to improve the
driver's visibility depending on the exte-
rior conditions:
- sidelamps, to be seen,
- dipped beam headlamps, to see with-out dazzling other drivers,
- main beam headlamps, for good visibility when the road is clear,
- rear foglamp, to be seen from a dis- tance,
- front foglamps, for even better for- ward vision.
Programming
Various automatic lighting control modes
are also available according to the fol-
lowing options:
- guide-me-home lighting,
- automatic illumination of headlamps. Selection is by turning ring
A .
Automatic illumination of
healamps Lighting on reminder
With the ignition off and the automatic
illumination of headlamps function
switched off, when the driver's door is
opened, a buzzer sounds if you have
left the lighting on.
Front foglamps and rear
foglamp
Rotate the ring forwards to switch on
and backwards to switch off. The status
i s c o n fi r m e d b y t h e i n d i c a t o r l a m p o n
the instrument panel.
V e h i c l e s fi t t e d w i t h a r e a r
foglamp (ring B)
Dipped/Main beam change
Pull the stalk towards you. When the lighting is switched off
automatically, the rear foglamp
and the dipped headlamps re-
main on (turn the ring backwards
to switch off the rear foglamp.
The dipped beam headlamps and
sidelamps then switch off).
This only operates with the dipped/main
beam headlamps.
Page 55 of 119
!
i
i
53
"Guide me home" lighting
When you leave your vehicle, the side-
lamps and dipped beam headlamps can
be left on for approximately 30 seconds.
To do this:
- place the key in the STOP position,
- place the lighting stalk in the 0 posi-
tion,
- fl a s h t h e h e a d l a m p s ,
- get out of the vehicle and lock it. D i r e c t i o n i n d i c a t o r s ( fl a s h e r s )
Left: downwards.
Right: upwards.
In good or rainy weather, both
day and night, the front foglamps
and the rear foglamp cause daz-
zle and their use is prohibited.
Do not forget to switch them off
when they are no longer needed.
V e h i c l e s fi t t e d w i t h f r o n t
foglamps and a rear foglamp
(ring C)
When the lighting is switched off
automatically or when the dipped
beam headlamps are switched
off manually, the front foglamps,
the rear foglamp and the side-
lamps remain on (turn the ring
backwards to switch off the front
foglamps. The sidelamps then
switch off).
F r o n t f o g l a m p s ( fi r s t r o t a t i o n o f t h e r i n g
forwards)
To switch off the rear foglamp and
the front foglamps, turn the ring
backwards twice in succession.
The front foglamps operate with the
sidelamps, the dipped beam headlamps
and the main beam headlamps.
Front and rear foglamps (2nd rotation of
the ring forwards).
Page 56 of 119
54
AUTOMATIC ILLUMINATION OF
HEADLAMPS
The sidelamps and dipped beam head-
lamps come on automatically if the light
is poor and when the windscreen wip-
ers operate continuously and switch off
when the light becomes bright enough
or the windscreen wipers are switched
off.
I n f o g g y w e a t h e r o r i n s n o w , t h e
sun-
shine
s e n s o r m a y d e t e c t s u f fi c i e n t
l i g h t , t h e l i g h t i n g w i l l n o t c o m e o n a u -
t o m a t i c a l l y . I f n e c e s s a r y , t h e d i p p e d
b e a m h e a d l a m p s m u s t b e s w i t c h e d
on manually.
This function is active when the vehicle
is supplied to the customer.
To deactivate or activate the function:
- Place the key in the accessories po- sition (1st notch),
- Place the lighting stalk in the 0 posi-
tion,
- Press the end of the lighting stalk for more than four seconds.
Do not cover the
sunshine
s e n s o r ,
c o u p l e d w i t h t h e r a i n s e n s o r , l o c a t e d
i n t h e c e n t r e o f t h e w i n d s c r e e n , b e -
h i n d t h e r e a r v i e w m i r r o r . I t i s u s e d
for the automatic illumination of
headlamps. Operating check
Activation
Activation is accompanied by an audible
signal and a message in the multifunc-
tion screen.
Deactivation
Deactivation is accompanied by an au-
dible signal.
When the driver uses the manual light-
ing controls, the function is temporarily
deactivated.
If the
sunshine
sensor does not func-
tion correctly , the lighting come on ac-
companied by an audible signal and a
message in the multifunction screen.
Consult a PEUGEOT dealer.
HEADLAMP ADJUSTMENT
Depending on the load in your vehicle,
it is recommended that the headlamp
beam is adjusted.
0. 1 or 2 people in the front seats.
-. 3 people.
1. 5 people.
2. 5 people + maximum authorised
load.
3. Driver + maximum authorised load.
Initial setting is position 0.
Page 57 of 119
55
WIPER CONTROL STALK
System for selecting and controlling the
various front and rear wiping modes for
clearing rain and cleaning.
The front and rear wipers of the vehicle
are designed to improve the driver's
visibility progressively according to the
weather conditions.
Programming
Various automatic wiper control modes
are also available according to the fol-
lowing options:
- automatic rain sensitive windscreen wipers,
- rear wiping when reverse gear is en- gaged. F r o n t w i n d s c r e e n w i p e r w i t h
i n t e r m i t t e n t w i p e
2 Fast wipe (heavy rain).
1 Normal wipe (moderate rain).
I Intermittent wipe.
0 Off.
Single wipe (press downwards).
In the I ntermittent position, the wiping
speed is in proportion to the vehicle
speed. F r o n t w i n d s c r e e n w i p e r w i t h
a u t o m a t i c w i p e
2 Fast wipe (heavy rain).
1 Normal wipe (moderate rain).
AUTO Automatic wipe.
0 Off.
Single wipe (press downwards).
In the AUTO position, the wiping speed
is in proportion to the intensity of the
rainfall.
If the ignition has been off for more than
one minute, with the wipers stalk in a
position other than off, t h e w i p e r s m u s t
be must be reactivated :
- move the stalk to any position,
- then move it back to the required position.
Page 58 of 119
i
56
A u t o m a t i c r a i n s e n s i t i v e w i n d s c r e e n
w i p e r s
In the AUTO position, the windscreen
wipers operate automatically and adapt
their speed to the intensity of the
rainfall .
Operating check
Activation
Activation of the function is accompa-
nied by a message on the multi-function
screen.
In the event of malfunction , the driver
is informed by an audible signal.
In the AUTO position, the windscreen
wiper will operate in intermittent mode.
Contact a PEUGEOT dealer to have the
system checked.
Do not cover the rain sensor located
on the windscreen behind the rear view
mirror.
When using an automatic car wash,
switch off the ignition or check that the
wiper stalk is not in the AUTO position.
In winter, it is advisable to wait for the
windscreen to completely clear of ice
before operating the automatic rain
sensitive wipers.
W i n d s c r e e n w a s h
Pull the wiper stalk towards you. The
windscreen wash, then the windscreen
w i p e r s , o p e r a t e f o r a s p e c i fi e d t i m e .
R e a r s c r e e n w i p e r
Turn ring A t o t h e fi r s t n o t c h f o r i n t e r m i t -
tent wiping.
I f t h e i g n i t i o n i s s w i t c h e d o f f , i t i s
necessary to reactivate the control
each time . To do this, move the stalk
to any position, then move it back to the
required position.
A u t o m a t i c r e a r s c r e e n w i p e r
When the windscreen wipers control is
activated and you engage reverse gear,
the rear screen wiper operates intermit-
tently.
R e a r s c r e e n w a s h
Turn ring A p a s t t h e fi r s t n o t c h ; t h e
screen wash then the wiper operate for
a fi x e d p e r i o d . If you use a bicycle carrier, con-
sult a PEUGEOT dealer to have
this function deactivated or install
a s p e c i fi c b i c y c l e c a r r i e r a p p r o v e d
by PEUGEOT. COURTESY LAMPS
System for selecting and controlling the
various passenger compartment lamps.
Front courtesy lamp (button A)
- when the vehicle is unlocked,
- when a door is opened,
- when the ignition is switched off.
It switches off when the vehicle is
locked.
I t fl a s h e s w h i l e d r i v i n g i f a d o o r i s n o t
closed correctly.
Permanently off.
Permanently on, when the key
is in the accessories position or
with the ignition on.
In this position, the courtesy
lamp comes on for approxi-
mately 30 seconds:
Page 59 of 119
i
56
A u t o m a t i c r a i n s e n s i t i v e w i n d s c r e e n
w i p e r s
In the AUTO position, the windscreen
wipers operate automatically and adapt
their speed to the intensity of the
rainfall .
Operating check
Activation
Activation of the function is accompa-
nied by a message on the multi-function
screen.
In the event of malfunction , the driver
is informed by an audible signal.
In the AUTO position, the windscreen
wiper will operate in intermittent mode.
Contact a PEUGEOT dealer to have the
system checked.
Do not cover the rain sensor located
on the windscreen behind the rear view
mirror.
When using an automatic car wash,
switch off the ignition or check that the
wiper stalk is not in the AUTO position.
In winter, it is advisable to wait for the
windscreen to completely clear of ice
before operating the automatic rain
sensitive wipers.
W i n d s c r e e n w a s h
Pull the wiper stalk towards you. The
windscreen wash, then the windscreen
w i p e r s , o p e r a t e f o r a s p e c i fi e d t i m e .
R e a r s c r e e n w i p e r
Turn ring A t o t h e fi r s t n o t c h f o r i n t e r m i t -
tent wiping.
I f t h e i g n i t i o n i s s w i t c h e d o f f , i t i s
necessary to reactivate the control
each time . To do this, move the stalk
to any position, then move it back to the
required position.
A u t o m a t i c r e a r s c r e e n w i p e r
When the windscreen wipers control is
activated and you engage reverse gear,
the rear screen wiper operates intermit-
tently.
R e a r s c r e e n w a s h
Turn ring A p a s t t h e fi r s t n o t c h ; t h e
screen wash then the wiper operate for
a fi x e d p e r i o d . If you use a bicycle carrier, con-
sult a PEUGEOT dealer to have
this function deactivated or install
a s p e c i fi c b i c y c l e c a r r i e r a p p r o v e d
by PEUGEOT. COURTESY LAMPS
System for selecting and controlling the
various passenger compartment lamps.
Front courtesy lamp (button A)
- when the vehicle is unlocked,
- when a door is opened,
- when the ignition is switched off.
It switches off when the vehicle is
locked.
I t fl a s h e s w h i l e d r i v i n g i f a d o o r i s n o t
closed correctly.
Permanently off.
Permanently on, when the key
is in the accessories position or
with the ignition on.
In this position, the courtesy
lamp comes on for approxi-
mately 30 seconds:
Page 60 of 119
i
57
DIRECTION INDICATORS
Lower the lighting stalk when moving
to the left.
Raise the lighting stalk when moving to
the right.
HAZARD WARNING LAMPS
Press this button, the direction indi-
c a t o r s fl a s h .
They can operate with the ignition off.
Automatic operation of hazard
warning lamps
When braking in an emergency, de-
pending on the deceleration, the hazard
warning lamps come on automatically.
T h e y s w i t c h o f f a u t o m a t i c a l l y t h e fi r s t
time you accelerate.
You can also switch them off by
pressing the button.
Press one of the spokes of the steering
wheel.
Use the horn moderately and only
in the following cases:
- immediate danger,
- overtaking a cyclist or pedes- trian,
- when approaching an area where there is no visibility.
Audible warning to alert other road users
to an imminent danger.
Selection of the left or right direction in-
dicators to signal a change of direction
of the vehicle. A visual warning by means of the direc-
tion indicators to alert other road users to
a vehicle breakdown, towing or accident.