Peugeot 208 2014 Owner's Manual - RHD (UK, Australia)

169
Changing a bulb
Front lamps
A. Model with light guide
In some weather conditions (e.g. low
temperature or humidity), the presence
of misting on the internal sur face of the
glass of the headlamps and rear lamps
is normal; it disappears after the lamps
have been on for a few minutes.
The headlamps are fitted with
polycarbonate glass with a protective
coating:
F

d

o not clean them using a dr y
or abrasive cloth, nor with a
detergent or solvent product,
F

u

se a sponge and soapy water or
a pH neutral product,
F

w

hen using a high pressure washer
on persistent marks, do not keep
the lance directed towards the
lamps or their edges for too long,
so as not to damage their protective
coating and seals.
B. Model without light guide
1. Main beam headlamps (H7-55W).
2. D ipped beam headlamps (H7-55W).
3.
D

aytime running lamps / sidelamps
(light emitting diodes - LEDs).
4.
D

irection indicators (PWY-24W).
5.
F

ront foglamps (directional according
to version) (H11-55W). 1. M
ain beam headlamps (H7-55W).
2. D ipped beam headlamps (H7-55W).
3.
D

aytime running lamps / sidelamps
(W5-5W).
4.
D

irection indicators (PWY-24W).
5.
F

ront foglamps (directional according
to version) (H11-55W).
Changing a bulb should only be done
after the headlamp has been switched
off for several minutes (risk of serious
burns).
F

D

o not touch the bulb directly with
your fingers, use a lint-free cloth.
It is imperative to use only anti-
ultraviolet (
uV

) type bulbs to avoid
damaging the headlamp.
Always replace a failed bulb with a
new bulb with the same type and
specification.
7
Practical information

170
Amber coloured bulbs, such as the
direction indicators, must be replaced
with bulbs of identical specifications
and colour.
When refitting, close the protective
cover carefully to preserve the sealing
of the headlamp.
Rapid flashing of the direction indicator
warning lamp (right or left) indicates the
failure of a bulb on that side.
Changing direction indicator
bulbs
F Turn the bulb holder a quarter of a turn and
extract it.
F

P
ull out the bulb and change it.
To reassemble, carry out these operations in
reverse order.
C. GTi model
1. Main beam headlamps (H7-55W).
2. D ipped beam headlamps (H7-55W).
3.
D

aytime running lamps / sidelamps
(light emitting diodes - LEDs).
4.
D

irection indicators (light emitting
diodes - LEDs).
5.
F

ront foglamps (directional according
to version) (H11-55W).
Practical information

171
Changing main beam headlamp bulbs
F Remove the protective cover by pulling on the tab.F Disconnect the bulb connector.
F P ull out the bulb and replace it.
Changing daytime running lamp /
sidelamp bulbs
F Turn the bulb holder a quarter turn and pull it out.
F

P
ull out the bulb and replace it.
To reassemble, carry out these operations in
reverse order.
To reassemble, carry out these operations in
reverse order, positioning the alignment lug at
the bottom.
Changing dipped beam headlamp
bulbs
F Remove the protective cover by pulling on the tab.
F

D
isconnect the bulb connector.
F

Spread the spring to release the bulb (model A ).F extract the bulb and change it.
To reassemble, carry out these operations in
reverse order, positioning the alignment lug at
the bottom (model A) or at the top (model B ).
7
Practical information

172
Changing front foglamp /
directional lamps
F Access to the front foglamp is through the orifice below the bumper.
F

D
isconnect the bulb holder connector by
pressing on the top of the tongue.
F
e
x
tract the bulb holder by pressing on the
two clips clips (top and bottom).
F

R
eplace the module. To reassemble, carry out these
operations in reverse order.
To obtain this module, contact a
P
e

uge
O
T dealer or a qualified
workshop.
You can also contact a P
e

uge
O
T
dealer or a qualified workshop for this
replacement.
Changing the daytime running
lamps / sidelamps (light- emitting
diodes - LEDs)
For the replacement of this type of LeD l amp,
contact a Pe ugeO T dealer or a qualified
workshop.
Practical information

173
1. Brake lamps (P21W).
2. Reversing lamps (R10W).
3.
D

irection indicators (PY21W amber).
4.
S

idelamps (light emitting
diodes - LEDs).
Rear lamps
5. Foglamp (P21W).
Changing integrated direction
indicator side repeater bulbs
F Press the central tongue and remove the side repeater.
F

P
ull the bulb holder out and replace the
failed bulb.
To reassemble, carry out these operations in
reverse order.
You should contact a P
e

uge
O
T dealer or a
qualified workshop for the replacement of these
bulbs.
F
I
nsert a flat screwdriver between the mirror
glass and its base.
F
u
s

e the screwdriver as a lever to extract
the mirror glass.
F
u
n

clip the mirror shell by pressing on the
two retaining clips.
7
Practical information

174
Changing brake lamp, reversing lamp and direction indicator bulbs
These three bulbs are changed from inside the boot:F
o
pen the boot,
F

r
emove the access grille from the
corresponding side trim panel,
F

s
lacken and remove the nut,
F

d
isconnect the lamp unit connector,
F

u
nclip the lamp unit carefully extract it
pulling in line towards the outside, F

p
ress the four tabs and remove the bulb
h o l d e r,
F

t
urn the bulb a quarter of a turn and
change it.
To reassemble, carry out these operations in
reverse order.
Take care to engage the lamp unit in its guides,
while keeping it in line with the vehicle.
Tighten sufficiently to ensure sealing, but
without damaging the lamp.
Light emitting diodes-
LEDs
For replacement, contact a Pe ugeO T dealer
or qualified workshop.
Practical information

175
Changing the third brake lamp
bulbs
F unscrew the fixing pins on each side of the lamp, without removing them completely.
F

P
ush on the screws to unclip the lamp.
F

D
isconnect the lamp connector.
F

R
emove the lamp from the outside.
F

T
urn the bulb holder which corresponds
to the faulty bulb one quarter of a turn and
remove it.
F

P
ull the bulb and change it.
To refit, carry out these operations in reverse
o r d e r.
Number plate lamps
To facilitate the removal of the lamp, carry out
this operation with the tailgate half open.
F

I
nsert a thin screwdriver into the lens
cutout.
F

P
ush it outwards.
F

R
emove the lens.
F

C
hange the faulty bulb.
To refit, press on the lens to clip it in place. Access is by passing a hand under the bumper.
F
T urn the bulb holder a quarter of a turn and
pull it out.
F

D
isconnect the connector on the bulb
h o l d e r.
F

P
ull the bulb out and change it.
To refit, carry out these operations in reverse
o r d e r.
You can also contact a P
e

uge
O
T dealer or a
qualified workshop for the replacement of these
bulbs.
Changing a foglamp bulb
7
Practical information

176
Changing a fuse
The extraction tweezer is fitted to the back of
the fusebox cover located inside the glove box.
F
O
pen the glove box lid,
F

u
nclip the fusebox cover by pulling at the
top right,
F

d
isengage the cover completely and turn it
ove r,
Access to the tools
F remove the carrier on which the tweezer is fitted.
Practical information

177
To replace a fuse, you must:
F u se the special tweezer to extract the fuse
from its housing and check the condition of
its filament.
F

a
lways replace the failed fuse with a fuse
of the same rating (same colour); using a
different rating could cause faults (risk of
f i r e).
If the fuse fails again soon after replacement,
have the vehicle's electrical system checked by
a P
e

uge
O
T dealer or a qualified workshop.
Changing a fuse
Before changing a fuse:
F t he cause of the failure must be identified
and rectified,
F

a
ll electrical consumers must be switched
of f,
F

t
he vehicle must be immobilised with the
ignition off,
F

i
dentify the failed fuse using the tables and
layout drawings in the following pages. Good
Failed
P
e

uge
O
T will not accept responsibility
for the cost incurred in repairing your
vehicle or for rectifying malfunctions
resulting from the installation of
accessories not supplied and not
recommended by P
e

uge
O
T and
not installed in accordance with its
instructions, in particular when the
combined consumption of all of the
additional equipment connected
exceeds 10 milliamperes.Installing electrical
accessories
Your vehicle's electrical system is
designed to operate with standard or
optional equipment.
Before installing other electrical
equipment or accessories on your
vehicle, contact a P
e

uge
O
T dealer or
a qualified workshop.
The replacement of a fuse not shown in
the tables below may cause a serious
malfunction of your vehicle. Contact
a P
e

uge
O

T dealer or a qualified
workshop. Tw e e z e r
7
Practical information

178
Fuse N°Rating Functions
F01 40 AHeated rear window.
F02 10 AHeated door mirrors.
F03 30 AFront one-touch windows.
F04 -Not used.
F05 30 ARear one-touch windows.
F06 10 AFolding door mirrors.
F07 10 AFolding door mirrors.
F08 -Not used.
F09 -Not used.
F10 20 AHi-Fi amplifier.
F11 -Not used.
F12 -Not used.
Fuses in the dashboard
The fusebox is placed in the lower dashboard
(right-hand side).
Access to the fuses
F Refer to the paragraph "Access to the tools".
Fuse tables
Practical information