Peugeot 208 2015 Owner's Manual

In the event of a breakdown199
208_en_Chap08_cas-de-panne_ed01-2016
1. Brake lamps (light- emitting diodes - LEDs).
2.
R

eversing lamps (P21W).
3.
D

irection indicators (PY21W amber).
4.
S

idelamps (light-emitting diodes -
LEDs).
Rear lamps
5. Foglamp (P21W).
Changing integrated direction
indicator side repeater bulbs
F Insert a flat screwdriver between the mirror glass and its base.
F

U
se the screwdriver as a lever to extract
the mirror glass.
F

U
nclip the mirror shell by pressing on the
two retaining clips. To reassemble, carry out these
operations in reverse order.
You should contact a PEUGEOT
dealer or a qualified workshop for the
replacement of these bulbs.
F
P ress the central tongue and remove the
side repeater.
F

P
ull the bulb holder out and replace the
failed bulb.
8

In the event of a breakdown
200
208_en_Chap08_cas-de-panne_ed01-2016
Changing reversing lamp and
direction indicator bulbs
These two bulbs are changed from inside the
boot:
F
O
pen the boot.
F

R
emove the access grille from the
corresponding side trim panel.
F

S
lacken and remove the nut.
F

D
isconnect the lamp unit connector.
F

U
nclip the lamp unit carefully extract it
pulling in line towards the outside. F

P
ress the four tabs and remove the bulb
h o l d e r.
F

T
urn the bulb a quarter of a turn and
change it.
To reassemble, carry out these operations in
reverse order.
Take care to engage the lamp unit in its guides,
while keeping it in line with the vehicle.
Tighten sufficiently to ensure sealing, but
without damaging the lamp.
Light- emitting diodes - LEDs
For replacement, contact a PEUGEOT
dealer or qualified workshop.

In the event of a breakdown201
208_en_Chap08_cas-de-panne_ed01-2016
Changing the third brake lamp
bulbs
F Unscrew the fixing pins on each side of the lamp, without removing them completely.
F

P
ush on the screws to unclip the lamp.
F

D
isconnect the lamp connector.
F

R
emove the lamp from the outside.
F

T
urn the bulb holder which corresponds
to the faulty bulb one quarter of a turn and
remove it.
F

P
ull the bulb and change it.
To refit, carry out these operations in reverse
o r d e r.
Number plate lamps
To facilitate the removal of the lamp, carry out
this operation with the tailgate half open.
F

I
nsert a thin screwdriver into the lens
cutout.
F

P
ush it outwards.
F

R
emove the lens.
F

C
hange the faulty bulb.
To refit, press on the lens to clip it in place. Access is by passing a hand under the bumper.
F
T urn the bulb holder a quarter of a turn and
pull it out.
F

D
isconnect the connector on the bulb
h o l d e r.
F

P
ull the bulb out and change it.
To refit, carry out these operations in reverse
o r d e r.
You can also contact a PEUGEOT dealer or a
qualified workshop for the replacement of these
bulbs.
Changing a foglamp bulb
8

In the event of a breakdown
202
208_en_Chap08_cas-de-panne_ed01-2016
Fuses
For the dashboard:
F U nclip the cover by pulling at the top left,
then right.
F

D
isengage the cover completely and turn it
ove r.
F

R
emove the carrier on which the tweezer is
fitted.
The extraction tweezer is fitted to the back of
the dashboard or glove box fusebox cover.
Access to tools
For the glove box:
F
O pen the glove box lid.
F

U
nclip the fusebox cover by pulling at top
right.
F

D
isengage the cover fully and turn it over.
F

R
emove the back of the carrier on which
the tweezer is fitted.

In the event of a breakdown203
208_en_Chap08_cas-de-panne_ed01-2016
To replace a fuse, you must:
F u se the special tweezer to extract the fuse
from its housing and check the condition of
its filament.
F

a
lways replace the failed fuse with a fuse
of the same rating (same colour); using
a different rating could cause faults (risk
of


f i r e).
If the fuse fails again soon after replacement,
have the vehicle's electrical system checked by
a PEUGEOT dealer or a qualified workshop. Before changing a fuse:
F
t
he vehicle must be immobilised with the
ignition off,
F
a
ll electrical consumers must be switched
of f,
F
i
dentify the failed fuse using the tables and
layout drawings in the following pages.
GoodFailed
PEUGEOT will not accept responsibility
for the cost incurred in repairing your
vehicle or for rectifying malfunctions
resulting from the installation of
accessories not supplied and not
recommended by PEUGEOT and
not installed in accordance with its
instructions, in particular when the
combined consumption of all of the
additional equipment connected
exceeds 10 milliamperes.
Installing electrical
accessories
Your vehicle's electrical system is
designed to operate with standard or
optional equipment.
Before installing other electrical
equipment or accessories on your
vehicle, contact a PEUGEOT dealer or
a qualified workshop.
The replacement of a fuse not shown in
the tables below may cause a serious
malfunction of your vehicle. Contact
a PEUGEOT dealer or a qualified
workshop. Tw e e z e r
Professional repairers: for full information
on the fuses and relays, consult the
wiring information and diagrams available
at a PEUGEOT dealer.
8

In the event of a breakdown
204
208_en_Chap08_cas-de-panne_ed01-2016
Fuse N° Rating Functions
F2 5 ADoor mirrors, headlamps, diagnostic socket.
F9 5 AAlarm.
F10 5 AIndependent telematic unit, trailer interface.
F11 5 AElectrochrome rear view mirror, additional heating.
F13 5 AHi-Fi amplifier, parking sensors
F16 15 AFront 12 V socket.
F17 15 AAudio system, audio system (accessory).
F18 20 ATouch screen.
On the left

In the event of a breakdown205
208_en_Chap08_cas-de-panne_ed01-2016
Fuse N°Rating Functions
F23 5 AVanity mirror, map reading lamps.
F26 15 AHorn.
F27 15 AScreenwash pump.
F28 5 AAnti-theft.
F29 15 AAir conditioning compressor.
F30 15 ARear wiper.
8

In the event of a breakdown
206
208_en_Chap08_cas-de-panne_ed01-2016
Fuse N° Rating Functions
F01 40 AHeated rear window.
F02 10 AHeated door mirrors.
F03 30 AFront one-touch windows.
F04 -Not used.
F05 30 ARear one-touch windows.
F06 10 AFolding door mirrors.
F07 10 AFolding door mirrors.
F08 -Not used.
F09 15 AFront heated seats.
F10 20 AHi-Fi amplifier.
F11 -Not used.
F12 -Not used.
On the right

In the event of a breakdown207
208_en_Chap08_cas-de-panne_ed01-2016
Fuse N°Rating Functions
F16 15 AFront foglamps.
F18 10 ARight hand main beam headlamp.
F19 10 ALeft hand main beam headlamp.
F25 30 AHeadlamp wash relay (accessory).
F29 40 AFront wiper motor.
Engine compartment
Access to the fuses
F Unclip the cover.
F
C hange the fuse (see corresponding
paragraph).
F

W
hen you have finished, close the cover
carefully to ensure correct sealing of the
fusebox.
The fusebox is placed in the engine
compartment near the battery (left-hand side).
8

In the event of a breakdown
208
208_en_Chap08_cas-de-panne_ed01-2016
12 V battery
Versions equipped with Stop & Start are
fitted with a 12 V lead-acid battery of
specific technology and specification.
Its replacement should be carried
out only by a PEUGEOT dealer or a
qualified workshop.
Procedure for starting the engine using another battery or charging a discharged battery.
The battery is located under the bonnet.
To gain access to it:
F o pen the bonnet using the interior release
lever, then the exterior safety catch,
F

s
ecure the bonnet stay,
F

r
emove the plastic cover on the (+)
terminal.
Access to the battery
If your vehicle has an automatic
gearbox, do not try to start the engine
by pushing the vehicle.
Batteries contain harmful substances
such as sulphuric acid and lead.
They must be disposed of in
accordance with regulations and must
not, in any circumstances, be discarded
with household waste.
Take used remote control batteries and
vehicle batteries to a special collection
point.
General points
Lead-acid starter batteries
Protect your eyes and face before
handling the battery.
All operations on the battery must be
carried out in a well ventilated area and
away from naked flames and sources
of sparks, so as to avoid the risk of
explosion or fire.
Wash your hands afterwards.
If your vehicle has an electronic
gearbox, do not try to start the engine
by pushing the vehicle.
The (-) terminal of the battery is not accessible.
A remote earth point is located on the engine.