clutch Peugeot 208 2015 Owner's Manual

15
208_en_Chap01_instruments-bord_ed01-2016
Warning / indicator lamp State Cause Action / Observations
Diesel engine
pre-heating fixed.
The key is at position 2 (ignition on) in
the ignition switch. Wait until the warning lamp goes off before starting.
The period of illumination of the warning lamp is
determined by the ambient conditions (up to about
30
seconds in very low temperatures).
If the engine does not start, switch the ignition off and
then on, wait until the warning lamp goes off again,
then start the engine.
Parking brake
fixed. The parking brake is applied or not
properly released. Release the parking brake to switch off the warning
lamp, keeping your foot on the brake pedal.
Observe the safety recommendations.
For more information on the parking brake, refer to the
corresponding section.
Foot on the
brake pedal fixed.
The brake pedal must be pressed. With an electronic gearbox, press the brake pedal to
start the engine (lever in position N).
With an automatic gearbox, with the engine running,
press the brake pedal before releasing the parking
brake, to unlock the lever and come out of position P .
If you wish to release the parking brake without
pressing the brake pedal, this warning lamp will
remain on.
flashing. With an electronic gearbox, if you
hold the vehicle on an incline using
the accelerator for too long, the
clutch overheats. Use the brake pedal and/or the parking brake.
1
Instruments

16
208_en_Chap01_instruments-bord_ed01-2016
Warning / indicator lamp State Cause Action / Observations
Foot on the
clutch fixed.
In the STOP mode of Stop & Start,
changing to START mode is refused
because the clutch pedal is not fully
down. You must declutch fully to allow the change to engine
S TA R T m o d e .
Stop & Star t fixed. When the vehicle stops (red lights,
traffic jams, ...) the Stop & Start system
has put the engine into STOP mode. The warning lamp goes off and the engine restarts
automatically in START mode, as soon as you want to
move off.
flashes for a few
seconds, then goes
of f. STOP mode is temporarily
unavailable.
Or
START mode is invoked
automatically. For more information on Stop & Start, refer to the
corresponding section.
Automatic
wiping fixed.
The wiper control is pushed
downwards. Automatic front wiping is activated.
To deactivate automatic wiping, operate the control
stalk downwards or put the stalk into another position.
Passenger's
airbag system fixed.
The control, located in the glove box,
is set to the OFF position.
The passenger's front airbag is
deactivated.
You can install a rear ward facing
child seat, unless there is a fault with
the operation of the airbags (Airbag
warning lamp on). Set the control to the ON
position to activate the
passenger's front airbag.
In this case, do not fit a child seat in the rear ward
facing position.
Instruments

Driving119
208_en_Chap06_conduite_ed01-2016
Moving off - Gearbox
Electronic Automatic
Do not drive with your hand resting on
the gear lever as this risks damaging
the gearbox. F

R
elease the parking brake.
F
Sel
ect position D
.
F P rogressively release the brake pedal.
Manual
F Start the engine.
F

E
ngage first gear.
F

R
elease the parking brake.
F

P
rogressively release the clutch pedal and
accelerate away. F
T o start the engine, place the lever at
position N .
F

P
ress firmly on the brake pedal.
F

S
tart the engine.
F

Sel
ect position A.
F

R
elease the parking brake.
F

P
rogressively release the brake pedal, then
accelerate away. F
A pply the parking brake.
F Sel ect position P or N.
F

S
tart the engine.
There is an audible signal, accompanied by the
display of an alert message, if the gear lever is
not in the right position.
If you move off in position M , remember
to operate the lever or a paddle to
engage the gear. F

W
ith the engine running, press the
brake pedal.
The vehicle then moves off.
F

P
ress the clutch pedal fully down.
6

Driving
120
208_en_Chap06_conduite_ed01-2016
Switching off
Ignition
Key left in the "Ignition on" position
On opening the driver's door, an alert
message is displayed, accompanied
by an audible signal, to remind you that
the key is still in the ignition switch at
position 1 (Stop) .
If the key has been left in the ignition
switch at position 2 (Ignition on) ,
the ignition will be switched off
automatically after one hour.
To switch the ignition back on, turn the
key to position 1 (Stop) , then back to
position 2 (Ignition on) .
Coasting
As a safety measure, do not coast (free-wheeling
in neutral or with the clutch pedal depressed).
Switching off the engine leads to a loss
of braking assistance.
Gearbox
Manual
F Place the gear lever in neutral.
F
Imm obilise the vehicle.
F

A
pply the parking brake.
F

T
urn the key towards you to position 1
(Stop) .
F

R
emove the key from the ignition switch.
Electronic
F Place the gear lever at position N .
F Imm obilise the vehicle.
F

A
pply the parking brake.
F

T
urn the key towards you to position 1
(Stop) .
F

R
emove the key from the ignition switch.
Automatic
F Place the gear lever at position P or N .
F Imm obilise the vehicle.
F

A
pply the parking brake.
F

T
urn the key towards you to position 1
(Stop) .
F

R
emove the key from the ignition switch.
Steering wheel
To facilitate unlocking of the steering
wheel, it is recommended that you
place the wheels in the straight ahead
position before switching off the engine.

Driving
122
208_en_Chap06_conduite_ed01-2016
Only engage reverse gear when the vehicle
is stationary and the engine is at idle.
As a safety precaution and to facilitate
starting of the engine:
-
a
lways select neutral,
-

p
ress the clutch pedal.
6-speed
Engaging reverse gear
Manual gearbox
5-speed
F Move the lever fully to the right to engage 5th or 6th g e a r.
F
M
ove the gear lever fully to the right to
engage 5th g e a r.
Engaging reverse gear
F Move the gear lever fully to the right then back. F
R aise the collar below the gear lever knob,
then push the lever fully to the left and then
forward. The gear shift indicator is displayed in
the instrument panel.
Only engage reverse gear when the
vehicle is stationary and the engine is
at idle.

Driving131
208_en_Chap06_conduite_ed01-2016
Stop & Start
The "ECO" lamp comes on in the
instrument panel and the engine goes
into standby.
Operation
STOP mode
With e-HDi or BlueHDi Diesel and an
electronic gearbox:
-

S
peed below 4 mph (6 km/h).
-

G
ear lever in position N
Or
-
B

rake pedal pressed.
Special cases
STOP mode is not invoked when:
- the driver's door is open,
-

t
he driver's seat belt is not fastened,
-

t
he vehicle has not exceeded 6 mph
(10 km/h) since the last engine start using
t h e key,
-

t
he engine is needed to maintain a
comfortable temperature in the passenger
compartment,
-
d

emisting is selected,
-
s

ome special conditions (battery charge,
engine temperature, braking assistance,
ambient temperature...) where the engine is
needed to assure control of a system.
The "ECO" lamp flashes for a few
seconds then goes off.
This operation is perfectly normal.
The system puts the engine temporarily into
standby - STOP mode - during stops in the
traffic (red lights, traffic jams, ...). The engine
restarts automatically - START mode - as soon
as you want to move off. The restart takes
place instantly, quickly and silently.
Per fect for urban use, the Stop & Start system
reduces fuel consumption and exhaust
emissions as well as the noise level when
stationary.
With BlueHDi Diesel and a manual gearbox:
-

A

s soon as the vehicle stops.
-

G

ear lever in neutral and clutch pedal
released.
With PureTech petrol and a manual,
electronic or automatic gearbox:
-

A

s soon as the vehicle stops.
-

G

ear lever in neutral and clutch pedal
released (manual gearbox).
-

B

rake pedal pressed or gear lever in
position N (electronic or automatic
gearbox).
6

Driving
132
208_en_Chap06_conduite_ed01-2016
For your comfort, during parking
manoeuvres, STOP mode is not
available for a few seconds after
coming out of reverse gear.
The Stop & Start system does not affect
the functionality of the vehicle, such as
for example, braking, ...
Never refuel with the engine in STOP
mode; you must switch off the ignition
with the key. A time counter calculates the sum
of the periods in STOP mode
during a journey. It rests itself
to zero every time the ignition is
switched on with the key.
Advice
S TA R T m o d e
Special casesAs a safety measure and for your comfort,
START mode is invoked automatically when:
-
y

ou open the driver's door,
-
y

ou unfasten the driver's seat belt,
-
s

ome special conditions (battery charge,
engine temperature, braking assistance,
ambient temperature...) where the engine is
needed for control of a system.
The "ECO" warning lamp flashes for
a few seconds, then goes off.
This operation is perfectly normal.
With a manual gearbox
:
-

C

lutch pedal depressed.
With an electronic / automatic gearbox :
-

G

ear lever in position A / D or M .
-
B

rake pedal released. The "ECO"
lamp goes off and the
engine restarts.
or
-

G

ear lever in position N .
-
B

rake pedal released.
-

T

hen gear lever in position A / D or M .
or
-
R

everse gear engaged.
With a manual gearbox in STOP mode,
if you engage a gear without fully
depressing the clutch pedal, a message
is displayed asking you to fully depress
the clutch pedal so that the engine can
restart.

Driving137
208_en_Chap06_conduite_ed01-2016
Temporarily exceeding the
speed
Registering a cruise speed
setting
- Bring the vehicle up to the desired speed by pressing the accelerator.
Pause (OFF)
- Press this button or the brake or clutch pedal.
Resume
- After the cruise control has been paused, press this button.
The vehicle returns to the last registered speed.
Or, you can also start the procedure for
"Registering a cruise speed setting".
Changing the registered
speed setting
To register a speed higher than the previous
setting, there are two possibilities.
-

P

ress the SET - or SET +
button
The speed setting is registered/activated and
the vehicle will maintain this speed. It is possible to accelerate
and temporarily
drive at a speed higher than the registered
speed setting.
The cruise speed setting value flashes.
When the accelerator pedal is released, the
vehicle will return to the registered speed
setting.
6

Driving147
208_en_Chap06_conduite_ed01-2016
Park Assist
For entry into a parking space (parallel
parking) the system does not detect
spaces which are clearly much smaller
or larger than the size of the vehicle.
This "parking assistance" system
is activated automatically during
manoeuvres; it is therefore possible
that a symbol comes on in the screen,
accompanied by an audible signal,
without affecting the manoeuvre. The selection of the type of manoeuvre
(entering or exiting a parallel parking
space) prevents a change to STOP
mode of Stop & Start.
In STOP mode, this selection restarts
the engine.
The Park Assist system cannot in any
circumstances replace the need for
vigilance on the part of the driver.
The driver must remain in control of
their vehicle ensuring that the space
remains clear during the manoeuvre.
In some circumstances, the sensors
may not detect small obstacles located
in their blind spots. During a manoeuvre the steering wheel
turns quickly: do not hold the steering
wheel, do not place your hand between
the spokes of the steering wheel and
take care with loose and bulky clothing,
scarves, handbags... There is a risk of
injury.
The driver can take back control of the steering
at any time by grasping the wheel.
Changing tyre sizes (out-size tyres,
winter tyres, ...) can inter fere with
the correct operation of the parking
assistance system. The system provides assistance in entering and
exiting a parking space when parallel parking.
The system detects a parking space and then
provides assistance with the parallel parking
manoeuvres.
It controls the steering and provides visual and
audible information to the driver.
The driver manages the accelerator, brakes,
gears and the clutch in the case of a manual
gearbox.
6