ECO mode Peugeot 208 2017 User Guide

116
If the lever is not in position P, a message
appears in the screen on opening the
driver's door or approximately 45
seconds
after switching off the ignition.
F

P
lace the lever at position P ; the
message disappears.
When driving on flooded roads or when
crossing a ford, proceed at walking pace.
When the ignition is on, the lighting
of this warning lamp, associated with
an audible signal and a message
on the screen, indicates a gearbox
fault.
In this case, the gearbox switches to back-up
mode and is locked in 3rd gear. You may feel
a substantial knock when changing from P
to R and from N to R. This will not cause any
damage to the gearbox.
Do not exceed 60
mph (100 km/h), local speed
restrictions permitting.
Contact a PEUGEOT dealer or a qualified
workshop as soon as possible. There is a risk of damage to the gearbox:
F
i f you press the accelerator and brake
pedals at the same time,
F

i
f you force the movement of the lever
from position P to another position with
a flat battery.
To reduce fuel consumption during
prolonged stops with the engine running
(traffic jams, etc.), position the gear lever
at N and apply the parking brake.Gear shift indicator
(Depending on engine.)
This system reduces fuel consumption by
recommending the most appropriate gear.
Depending on the driving situation and your
vehicle's equipment, the system may advise
you to skip one (or more) gear(s). You can
follow this instruction without engaging the
intermediate gears.
Gearshift recommendations should not be
considered obligatory. The configuration of the
road, the amount of traffic and safety remain
determining factors when choosing the best
gear. The driver thus remains responsible
for deciding whether to follow or ignore the
system's instructions.
This function cannot be deactivated.
With an electronic or automatic gearbox,
the system is only active in manual mode.
Driving

117
On BlueHDi Diesel versions with manual
gearbox, in certain driving conditions the
system may suggest changing into neutral so
that the engine can go into standby (STOP
mode with Stop & Start). In this case, N is
displayed in the instrument panel.Example:
-

Y
ou are in third gear.
-

Y
ou press the accelerator pedal.
-

T
he system may suggest that you engage a
higher gear.
The system adapts its gear shift
recommendation according to the driving
conditions (slope, load, etc.) and the
driver’s requirements (power, acceleration,
b r a k i n g , e t c .) .
The system never suggests:
-
e

ngaging first gear,
-
enga

ging reverse gear,
-
enga

ging a lower gear. On vehicle fitted with a manual gearbox,
the arrow may be accompanied by the
gear recommended.Hill start assist
System that holds your vehicle for around
2
seconds, the time to move your foot from the
brake pedal to the accelerator.
The hill start assist function cannot be
deactivated. However, use of the parking
brake to immobilise the vehicle interrupts
its function.
The information appears on the instrument
panel in the form of an arrow.
Uphill, with the vehicle stationar y, it will
briefly stop the vehicle from rolling back
when you release the brake pedal.
With an electronic gearbox, if you are in
position A.
With an automatic gearbox, if you are in D .
6
Driving

118
Hill start assist is only available when:
- y our foot on the brake pedal fully
immobilises the vehicle,
-

c
ertain conditions of gradient are met,
-

w
ith the driver’s door closed.
Downhill, with the vehicle stationary and
reverse gear engaged, the vehicle is held
for a shor t time when you release the brake
pedal.
Do not leave the vehicle while it is being
held temporarily by hill start assist.
If you need to leave the vehicle with the
engine running, apply the parking brake
manually. Then ensure that the parking
brake warning lamp lights up constantly on
the instrument panel.
Operating fault
The fixed illumination of these
warning lamps indicates a fault with
the system.
Have the system checked by a
PEUGEOT dealer or a qualified
workshop.
Stop & Start
The system puts the engine temporarily into
standby – STOP mode – during stops in the
traffic (red lights, traffic jams, etc.). The engine
restarts automatically – START mode – as
soon as you wish to leave again. Restarting
occurs instantaneously, quickly and silently.
Per fect for urban use, the Stop & Start system
reduces fuel consumption and exhaust
emissions as well as the noise level when
stationary.
STOP mode
The " ECO" warning lamp illuminates
in the instrument panel and the
engine goes into standby.
With e- HDi or BlueHDi Diesel and an
electronic gearbox :
-

S

peed below 4 mph (6 km/h).
-

G

ear lever in position N.
Or
-
B

rake pedal pressed.
Driving

119
With BlueHDi Diesel and a manual gearbox:
- A s soon as the vehicle stops or the speed is
less than 2
mph (3 km/h) (with 1.5 Blue HDi
engine).
-

G
ear lever in neutral and clutch pedal
released.
With PureTech petrol and a manual,
electronic or automatic gearbox :
-

A
s soon as the vehicle stops or the speed
is less than 2
mph (3 km/h) (with manual
gearbox and depending on which version
you have).
-

G
ear lever in neutral and clutch pedal
released (manual gearbox).
-

B
rake pedal pressed or gear lever in
position N (electronic or automatic gearbox).
Special cases: STOP mode not
available
STOP mode is not invoked when:
- t he driver's door is open,
-

t
he driver's seat belt is not fastened,
-

t
he vehicle has not exceeded 6 mph
(10
km/h) since the last engine start using
t h e key,
-

t
he engine is needed to maintain a
comfortable temperature in the passenger
compartment,
-

d
emisting is active, The ECO warning lamp flashes for a
few seconds, then goes off.
This operation is perfectly normal.
A time counter sums up the time
periods spent in STOP mode
during a journey. It resets every
time the ignition is switched on
using the key.
For your comfort, during parking
manoeuvres, STOP mode is not available
for a few seconds after coming out of
reverse gear.
The Stop & Start system does not affect
the functionality of the vehicle, such as for
example, braking, power steering, With a manual gearbox in STOP mode, if
a gear is engaged without fully depressing
the clutch pedal, a warning lamp comes
on or an alert message is displayed asking
you to depress the clutch pedal to restart
the engine.
Never refuel with the engine in STOP
mode; you must switch off the ignition
using the key.
START mode
The ECO warning lamp goes off and
the engine starts:
With a manual gearbox :
-

C

lutch pedal depressed.
With an electronic / automatic gearbox :
-

G

ear lever in position A / D or M .
-
B

rake pedal released.
or
-
s

ome special conditions (battery charge,
engine temperature, braking assistance,
exterior temperature, etc.) where the engine
is needed to control the system.
6
Driving

120
- Gear lever in position N.
- Brake pedal released.
-

T
hen gear lever in position A / D or M .
or
-
R

everse gear engaged.
Special cases: START invoked
automatically
As a safety measure and for your comfort,
START mode is invoked automatically when:
-
y
ou open the driver's door,
-
y

ou unfasten the driver's seat belt,
-
s

ome special conditions (battery charge,
engine temperature, braking assistance,
air conditioning setting, etc.) where the
engine is needed for control of the system
or vehicle.
The ECO warning lamp flashes for a
few seconds, then goes off.
This operation is perfectly normal.
Manual deactivation
In certain circumstances, such as the need
to maintain a comfortable temperature in the
passenger compartment, it may be preferable
to deactivate the Stop & Start system.
The system can be deactivated at any time,
once the ignition is switched on.
This control switches off the Stop & Start
system.
-
Press.
-

T
he indicator lamp in the control remains
on.
-

A m
essage is displayed.
If you are stationary in Stop mode, the engine
restarts immediately.
Manual reactivation
- Press.
- T he indicator lamp in the control goes off.
-

A c
onfirmation message is displayed. If the engine is in STOP mode, it restarts
immediately.
The Stop & Start system is reactivated
automatically every time the ignition is
switched on.
Opening the bonnet
Before doing anything under the bonnet,
deactivate the Stop & Start system to
avoid the risk of injury related to an
automatic change to START mode.
Driving on flooded roads
Before driving in a flooded area, it is
strongly recommended that you deactivate
the Stop & Start system.
For more information on Driving advice
,
particularly on flooded roads, refer to the
corresponding section.
Driving

121
Operating fault
In the event of a fault with the system, the ECO
OFF switch warning lamp flashes then comes
on fixed.
Have it checked by a PEUGEOT dealer or a
qualified workshop.
If a fault occurs in STOP mode, the vehicle
may stall. All of the instrument panel warning
lamps come on. It is then necessary to switch
the ignition off and to restart the engine using
t h e key.The Stop & Start system requires a
12
V battery of specific technology and
specification.
All work on this type of battery must be
carried out only by a PEUGEOT dealer or
a qualified workshop.
For more information on the 12
V batter y,
refer to the corresponding section.
Speed limiter "LIMIT"
The system prevents the vehicle from
exceeding the speed setting programmed by
the driver.
Steering mounted controls
1. Speed limiter mode selection / off.
2. Increases the set value.
3. Decreases the set value.
4. Speed limiter On / Pause. The vehicle responds to the accelerator until
resistance is felt in the pedal, which signifies
that the vehicle has reached the limiter speed
setting.
However, pressing the pedal beyond this point
of resistance to the floor permits exceeding
of the programmed speed. To resume use of
the limiter, simply reduce the pressure on the
accelerator pedal gradually and return to a
speed below that programmed.
Setting and operation of the system can be
done stationar y with the engine running or
when driving.
Selection
F Place the thumbwheel at the "LIMIT"

position: the speed limiter mode is selected
but is not switched on (PAUSE).
Switching the speed limiter on is not required to
set the speed limit.
The speed setting is selected with the engine
running, stationary or when driving. The
minimum speed setting possible is 20

mph
(30


km/h).
6
Driving

125
To register a speed higher than the previous
setting, there are two possibilities.
Without using the accelerator
- Press the SET + button.
A short press increases the speed setting by
1

mph (km/h).
Pressing and holding increases the setting in
steps of 5

mph (km/h).
By using the accelerator
- Exceed the saved speed until you reach the desired speed. -

P
ress the SET – or
SET + button.
To register a speed lower than the previous
setting:
-
P
ress the SET –
button.
A short press decreases the setting by 1 mph
(km/h).
Pressing and holding decreases the setting in
steps of 5 mph (km/h).
Switching the system off
- Place the thumbwheel at the 0 position:
cruise control mode is deselected. The
display returns to the total mileage recorder.
After switching off the ignition, all registered
speed settings are lost.
Operating fault
The registered speed is erased, then replaced
by three dashes.
Have it checked by a PEUGEOT dealer or a
qualified workshop.
Changing the registered
speed setting
6
Driving

143
Load reduction mode
System which manages the use of certain
functions according to the level of charge
remaining in the battery.
When the vehicle is being driven, the load
reduction function temporarily deactivates
certain functions, such as air conditioning,
heated rear screen, etc.
The deactivated functions are reactivated
automatically as soon as conditions permit.
Energy economy mode
System which manages the duration of use of
certain functions to conser ve a sufficient level
of charge in the battery.
After the engine has stopped, you can still use
functions such as the audio and telematics
system, windscreen wipers, dipped beam
headlamps, courtesy lamps, etc. for a
maximum combined duration of about forty
minutes.
Switching to this mode
A message appears in the instrument panel
screen indicating that the vehicle has switched
to economy mode and the active functions are
put on standby.If a telephone call is being made at this
time, it will be maintained for around
10
minutes with the Bluetooth hands-free
system of your audio system.
Exiting the mode
These functions will be automatically restored
the next time the vehicle is used. A flat battery prevents the engine from
starting.
For more information on the 12
V batter y
,
refer to the corresponding section.
In order to restore the use of these functions
immediately, start the engine and let it run:
-
f
or less than ten minutes, to use the
equipment for approximately five minutes,
-
f
or more than ten minutes, to use the
equipment for up to approximately thirty
minutes.
Let the engine run for the duration specified to
ensure that the battery charge is sufficient.
Do not repeatedly and continuously restart the
engine in order to charge the battery.
7
Practical information

145
As a safety measure and to avoid
damaging the roof, it is essential to use
the transverse bars approved for your
vehicle.
Obser ve the instructions on fitting and use
contained in the guide supplied with the
roof bars.
Recommendations
Distribute the load uniformly, taking care
to avoid overloading one of the sides.
Arrange the heaviest part of the load as
close as possible to the roof.
Lash the load securely.
Drive gently: the vehicle will be more
susceptible to the effects of side winds
and the stability of the vehicle may be
affected.
On a long journey, check the security of
the load at every stop.
Remove the roof bars once they are no
longer needed.Bonnet
The location of the interior bonnet release
lever prevents opening of the bonnet when
the left-hand front door is shut.
When the engine is hot, handle the
exterior safety catch and the stay with
care (risk of burns), using the protected
area.
When the bonnet is open, take care not to
damage the safety catch.
Do not open the bonnet under very windy
conditions.The cooling fan may star t after
switching off the engine: take care
with articles and clothing that might be
caught by the fan blades.
Because of the presence of electrical
equipment under the bonnet, it is
recommended that exposure to water
(rain, washing, etc.) be limited.Opening
F Open the left-hand front door.
F
P
ull the release lever A , located at the
bottom of the door aperture, towards you.
Before doing anything under the bonnet,
deactivate the Stop & Start system to
avoid the risk of injury related to an
automatic change to START mode.
7
Practical information

185
Engines and towed loads – PETROL
Engine1.2 PureTech 681.2 PureTech 821.2 PureTech 82
Gearboxes Manual 5-speed
(BVM5) Manual 5-speed
(BVM5) Electronic (5-speed)
(ETG5)
Code Q A5 (EB2FB MA)KQ5 (EB2F MA)KQP (EB2F MAPS)
CC..., CA... model codes HMP6HMZ6 – HMZ0 HMZ6/P – HMZ0/P
Cubic capacity (cm
3) 1,1 9 91,1 9 91,1 9 9
Max. power: EU standard (kW) 5060 60
Fuel UnleadedUnleadedUnleaded
Braked trailer (within the GTW limit) on a 12%
slope (Kg) 450 (VP)
4 8 5 ( VAS P) 820 (VP/VASP)
920 (LUV) 820
Unbraked trailer (kg) 450520520
Recommended nose weight (kg) 464646
VP: Private Vehicle.
VASP: Specialised Motor Vehicle.
LUV: Light Utility Vehicle.
9
Technical data