ESP Peugeot 208 2017 Owner's Manual
[x] Cancel search | Manufacturer: PEUGEOT, Model Year: 2017, Model line: 208, Model: Peugeot 208 2017Pages: 304, PDF Size: 11.45 MB
Page 12 of 304
10
Warning and indicator
lamps
When the ignition is switched on
Certain warning lamps come on for a few
seconds when the vehicle's ignition is switched
on.
When the engine is started, these same
warning lamps should go off.
If they remain on, before driving refer to the
information on the warning lamp concerned.
Associated warnings
Certain warning lamps may come on in one of
two modes: fixed (continuous) or flashing.
Only by relating the type of lighting to the
operating status of the vehicle can it be
ascertained whether the situation is normal or
whether a fault has occurred.
In the event of a fault, the illumination of the
warning lamp may be accompanied by an
audible signal and/or a message.
Warning lamps
When the engine is running or the vehicle is
being driven, illumination of one of the following
warning lamps indicates a fault which requires
action on the part of the driver.
Any fault resulting in the illumination of a
warning lamp must be investigated further
using the associated message.
If you encounter any problems, contact a
PEUGEOT dealer or a qualified workshop.
Operation indicator lamps
The lighting of one of the following indicator
lamps confirms that the corresponding system
is on.
Deactivation indicator lamp
If this indicator lamp comes on, this confirms
that the corresponding system has been
switched off intentionally.
This may be accompanied by an audible signal
and a message being displayed.
Visual identifiers informing the driver that
a system is in operation, switched off (on/
off indicator lamps) or has developed a fault
(warning lamp).
Dashboard instruments
Page 13 of 304
11
STOPFixed, associated with
another warning lamp,
accompanied by an
audible signal and a
message. Illumination of this warning
lamp is related to a serious
fault detected with the engine,
the braking system, the power
steering, etc., or a major
electrical fault. You must stop as soon as it is safe to do so.
Park, switch off the ignition and call a PEUGEOT
dealer or a qualified workshop.
Warning / indicator lamp
StateCause Action / Observations
Parking brake Fixed. The parking brake is applied or
not properly released. Release the parking brake to extinguish the warning
lamp; keep your foot on the brake pedal.
Observe the safety recommendations.
For more information on the Parking brake
, refer to
the corresponding section.
Braking Fixed. The brake fluid level has dropped
significantly. You must stop as soon as it is safe to do so.
Top up with brake fluid approved by PEUGEOT.
If the problem persists, have the system checked by a
PEUGEOT dealer or a qualified workshop.
+ Fixed, associated with
the ABS warning lamp.
The electronic brake force
distribution (EBFD) system is
faulty. You must stop as soon as it is safe to do so.
Have it checked by a PEUGEOT dealer or a qualified
workshop.
1
Dashboard instruments
Page 17 of 304
15
Warning / indicator lampStateCause Action / Observations
Under-inflation Fixed, accompanied
by an audible signal
and a message. One or more wheels has
insufficient pressure.
Check the pressure of the tyres as soon as possible.
This check should preferably be carried out when the
tyres are cold.
You must reinitialise the system after adjusting one or
more tyre pressures and after changing one or more
wheels.
For more information on Tyre under-inflation
detection
, refer to the corresponding section.
+ Flashing then fixed,
accompanied by the
Service warning lamp.
The system is faulty: tyre
pressures are no longer
monitored. Check the tyre pressures as soon as possible.
Have the system checked by a PEUGEOT dealer or a
qualified workshop.
Dynamic stability
control
(DSC/ASR) Flashing.
The DSC/ASR regulation is
operating. The system optimises traction and improves the
directional stability of the vehicle in the event of loss of
grip or trajectory.
Fixed. The DSC/ASR system has a fault. Have the system checked by a PEUGEOT dealer or a
qualified workshop.
Airbags Temporarily on. This warning lamp comes on for
a few seconds when you turn on
the ignition, then goes off.
This warning lamp should go off when the engine is started.
If it does not go off, contact a PEUGEOT dealer or a
qualified workshop.
Fixed.One of the airbag or seat belt
pyrotechnic pretensioner systems
has a fault. Have it checked by a PEUGEOT dealer or a qualified
workshop.
1
Dashboard instruments
Page 21 of 304
19
Warning / indicator lampStateCause Action / Observations
+
+ SCR emissions
control system
(BlueHDi Diesel)
Fixed, on switching
on the ignition,
associated with the
service and engine
diagnostic warning
lamps, accompanied
by an audible signal
and a message. A fault with the SCR emissions
control system has been
detected.
This alert disappears once the exhaust emissions
return to normal levels.
Flashing, on switching
on the ignition,
associated with
the service and
engine diagnostic
warning lamps,
accompanied by an
audible signal and a
message indicating
the remaining driving
range. After confirmation of the fault with
the emissions control system,
you can drive for up to 680
miles
(1,100
km) before the engine
starting inhibition system is
triggered. Contact a PEUGEOT dealer or a qualified workshop
without delay
, to avoid a breakdown .
Flashing, on switching
on the ignition,
associated with the
service and engine
diagnostic warning
lamps, accompanied
by an audible signal
and a message. You have exceeded the
authorised driving limit following
confirmation of a fault with the
emissions control system: the
engine starting inhibition system
prevents starting of the engine.
To be able to restart the engine, you must
call on a
PEUGEOT dealer or a qualified workshop.
For topping up or for more information on the AdBlue
® (BlueHDi engines) , refer to the corresponding section.
1
Dashboard instruments
Page 23 of 304
21
Warning / indicator lampStateCause Action / Observations
Diesel engine
pre-heating Fixed.
The key is at position 2 (ignition
on) in the ignition switch. Wait until the warning lamp goes off before starting.
The period of illumination of the warning lamp is
determined by the ambient conditions (up to about
thirty seconds in extreme conditions).
If the engine does not start, switch the ignition off and
then on, wait until the indicator lamp goes off again,
then start the engine.
Power steering Fixed. The power steering has a fault. Drive carefully at reduced speed.
Have the vehicle checked by a PEUGEOT dealer or a
qualified workshop.
Rear foglamp Fixed. The rear foglamp has been
switched on using the ring on the
lighting control stalk. Turn the ring on the lighting control stalk to the rear to
switch off the rear foglamp.
Stop & Star t Fixed. When the vehicle stops (red
lights, traffic jams, etc.), the Stop
& Start system puts the engine
into STOP mode. The warning lamp goes off and the engine restarts
automatically in START mode, as soon as you want to
move off.
Flashes for a few
seconds, then goes
of f. STOP mode is temporarily
unavailable.
or
START mode is triggered
automatically. For more information on Stop & Start, refer to the
corresponding section.
1
Dashboard instruments
Page 28 of 304
26
Resetting the service indicatorRetrieving the service
information
After each service, the service indicator must
be reset to zero.
If you have carried out the ser vice on your
vehicle yourself:
F
s
witch off the ignition,
If you have to disconnect the battery
following this operation, lock the vehicle
and wait at least 5
minutes for the reset to
be registered.
F
p
ress and hold the trip distance recorder
reset button,
F
s
witch on the ignition; the distance recorder
display begins a countdown,
F
w
hen the display indicates " =0", release
the button; the spanner disappears. You can access the ser vice information at any
time.
F
P
ress the trip distance recorder reset
button.
The ser vice information is displayed for a few seconds, then disappears.
Engine oil level indicator
(depending on version)
On versions fitted with an electric oil level
indicator, the state of the engine oil level is
displayed in the instrument panel for a few
seconds, after the servicing information. The level read will only be correct if the
vehicle is on level ground and the engine
has been off for more than 30
minutes.
Oil level incorrect
This is indicated by the display of the message
"Oil level incorrect" in the instrument panel
screen, accompanied by the ser vice warning
lamp and an audible signal.
If the low oil level is confirmed by a check using
the dipstick, the level must be topped up to
avoid damage to the engine.
For more information on Checking levels
,
refer to the corresponding section.
Oil level indicator fault
This is signalled by the display of the message
"Oil level measurement invalid" in the
instrument panel.
Contact a PEUGEOT dealer or a qualified
workshop.
Dashboard instruments
Page 29 of 304
27
AdBlue® range indicators
These range indicators are present only on
BlueHDi Diesel versions.
Once the AdBlue
® tank is on reser ve or after
detection of a fault with the SCR emissions
control system, when the ignition is switched
on, an indicator displays an estimate of the
distance that can be covered, the range, before
engine starting is prevented.
In the event of the risk of non-
starting related to a lack of
AdBlue
®
The engine start prevention system
required by regulations is activated
automatically once the AdBlue
® tank is
e m pt y.
In the event of a fault with the electric
indicator, the oil level is no longer
monitored.
If the system is faulty, you must check the
engine oil level using the manual dipstick
located under the bonnet.
For more information on Checking levels
,
refer to the corresponding section.
Range of the 1.6 BlueHDi engine
( E u r o 6 .1)
Range greater than 1,500 miles (2,400 km)
W hen switching on the ignition, there is no
automatic display of range in the instrument
panel.
Pressing this button
temporarily displays the
driving range with the
message "AdBlue: Range
greater than 1,500
miles
(2,400
km)" followed, if the
tank level of AdBlue permits,
with a message indicating
that you can top it up.
Remaining range between 1,500 and 375 miles
( 2,400 and 600 km) (1.6 BlueHDi Euro 6.1)
When switching on the ignition, the warning
lamp comes on, accompanied by an audible
signal and the display of a message (e.g. "Top
up AdBlue: Start-up not possible in x miles")
indicating the remaining range expressed in
miles or kilometres.
When driving, the message is displayed every
200
miles (300 km) until the level is topped up.
The reser ve level has been reached; it is
recommended that you top up as soon as
possible.
1
Dashboard instruments
Page 46 of 304
44
Automatic mode
(depending on version)
Open
Press the control, beyond the
resistance point: the window opens
completely when the switch is
released. Pressing the switch again
stops the movement of the window.
Close
Pull the control, beyond the
resistance point: the window closes
completely when the switch is
released. Pressing the switch again
stops the movement of the window.
The electric window controls remain
operational for approximately 1
minute
after the key has been removed.
Once this time has elapsed, the electric
windows will not operate. To reactivate
them, switch the ignition on again.
Anti-pinch
Deactivating the rear door
electric windows
For the safety of your children, press
the switch to prevent operation of
the electric windows of the rear
doors, irrespective of their position.
With the warning lamp on, the rear switches
are deactivated. With the warning lamp off, the
switches are active.
Reinitialisation
Following reconnection of the battery, the
safety anti-pinch function must be reinitialised.
The safety anti-pinch is not active during these
operations:
-
b
ring the window down completely, then
bring it back up. It will go up by a few
centimetres with each press. Repeat the
operation until the window is fully closed,
-
c
ontinue to pull the switch upwards for at
least 1
second after reaching this position,
window closed.
Always remove the key when leaving the
vehicle, even for a short time.
In the event of contact during operation
of the windows, you must reverse the
movement of the window. To do this, press
the switch concerned.
When operating the passenger electric
window switches, the driver must ensure
that no one is preventing correct closing of
the windows.
The driver must ensure that the
passengers use the electric windows
c o r r e c t l y.
Be aware of children when operating the
windows.
(depending on version)
When the window rises and meets an obstacle,
it stops and immediately partially lowers again.
In the event of unwanted opening
of the window when closing
automatically, press the switch until
the window opens completely, then
pull the switch immediately until the
window closes. Continue to hold the
control for approximately 1
second
after the window has closed.
The safety anti-pinch function is not active
during this operation.
Access
Page 49 of 304
47
Electric adjustments
F Move control A to the right or to the left to select the corresponding mirror.
F
M
ove control B in any of the four directions
to adjust.
F
R
eturn control A to its home position
(c e nt r e).
Folding / unfolding When locking the vehicle, the mirrors
fold automatically.
When unlocking the vehicle, the
mirrors unfold automatically.
F
W
ith the ignition on, pull control A
rear wards to fold the mirrors.
F
P
ull it again to unfold them. If the mirrors are folded using control A
,
they will not unfold when the vehicle is
unlocked. Pull again on control A .
Objects seen in the mirror are in reality
closer than they appear.
Take this into account when assessing
the distance of vehicles approaching from
behind.
The folding and unfolding of the door
mirrors using the remote control can be
deactivated by a PEUGEOT dealer or a
qualified workshop.
Fold the mirrors when putting your vehicle
through an automatic car wash.
If necessary, the mirrors can be folded
manually.
Rear view mirror
Equipped with an anti-dazzle system, which
darkens the mirror glass and reduces the
nuisance to the driver caused by the sun,
headlamps from other vehicles, etc.
Manual model
Adjustment
F A djust the mirror so that the mirror is
directed correctly in the "day" position.
Day / night position
F
P
ull the lever to change to the "night" anti-
dazzle position.
F
P
ush the lever to change to the normal
"day" position.
3
Ease of use and comfort
Page 55 of 304
53
One-piece rear bench
Bench seat with fixed one-piece cushion and
folding one-piece backrest.
Folding the backrest
F Move the front seats for ward if necessary.
F
P
osition the outer seat belts on the backrest
and buckle them.
F
L
ower the head restraints to the lowest
position. F
R
elease the seat backrest 2 by pressing
controls 1 simultaneously.
F
F
old the seat backrest 2 on to the fixed
cushion.
Raising the seat backrest
F Raise the seat backrest 2 .
F L atch the backrest in place, the red
indicators on each control 1 are no longer
visible.
F
U
nbuckle and return the outer seat belts to
their normal positions ready for use.
2/3 – 1/3 split rear bench
seat
Bench seat with fixed one-piece cushion and
split backrest (left-hand 2/3, right-hand 1/3)
which can be folded individually to adapt the
load space in the boot.
Folding the backrest
F Move the corresponding front seat for wards if necessary.
F
P
osition the corresponding outer seat belt
against the backrest and buckle it.
F
F
ully lower or remove the head restraint.
3
Ease of use and comfort