ad blue Peugeot 208 2017 User Guide

29
Remaining range less than 60 miles
( 100 km) (1.5 BlueHDi Euro 6.2)
When driving, the audible signal and the
message display are triggered every 6
miles
(10
km) until the AdBlue tank is topped up.
It is essential to top up as soon as possible and
before the tank is completely empty; other wise
it will not be possible to restart the engine after
the next stop. When switching on the ignition, this warning
lamp flashes, accompanied by an audible
signal (1 beep) and the display of a message
(e.g. "Top up AdBlue: Starting impossible
in x miles") indicating the remaining range
expressed in miles or kilometres.) Breakdown related to a lack of AdBlue
®
The AdBlue® tank is empty: the starting
inhibition system required by legislation
prevents starting of the engine.
To be able to restart the engine, it is
essential to add at least 4
litres of AdBlue
®
to its tank.
When switching on the ignition, this warning
lamp flashes, associated with an audible
signal and the display of the message "Top up
AdBlue: Starting impossible".
In the event of a fault with the
SCR emissions control system
An engine immobiliser is activated
automatically after you have driven a
further 650
miles (1,100 km) following
confirmation of a fault with the SCR
emissions control system. Have the
system checked by a PEUGEOT dealer or
a qualified workshop as soon as possible. In the event of the detection of a fault
If it is a temporary fault, the alert
disappears during the next journey,
after self-diagnostic checks of the SCR
emissions control system.
The warning lamps come on, accompanied
by an audible signal and the display of the
message "Emissions fault".
The alert is triggered while driving as soon
as the fault is detected for the first time, then
when switching on the ignition for subsequent
journeys, while the fault persists.
When driving, the audible signal and the
message display are triggered every 60

miles
(100

km) until the level is topped up.
It is essential to top up as soon as possible and
before the tank is completely empty; other wise
it will not be possible to restart the engine after
the next stop.
1
Dashboard instruments

30
Trip computer
Instrument panel display
screen
F Each press on the end of the wiper control stalk displays the information in
turn.
-
Trip 1 showing:
•
t

he average speed,
•
t

he average fuel consumption,
•

t
he distance travelled,
for the first trip.
Starting prevented
You have exceeded the authorised driving
limit: the starting prevention system does
not allow the engine to be started.
To be able to restart the engine, you must call
on a PEUGEOT dealer or a qualified workshop. Each time the ignition is switched on, these
warning lamps come on and the AdBlue
warning lamp flashes, accompanied by an
audible signal and the display of the message
"Emissions fault: Starting prevented".
During the permitted driving phase (between
685 and 0 miles (1,100 km and 0 km))
While driving, the message is displayed every
30 seconds while the fault with the SCR
emission control system persists.
The alert is repeated when switching on the
ignition.
You should go to a PEUGEOT dealer or a
qualified workshop as soon as possible.
Other wise you will not be able to restart the
vehicle. If a fault with the SCR system is confirmed
(after 30 miles (50 km) covered with the
permanent display of the message signalling
a fault), these warning lamps come on and the
AdBlue warning lamp flashes, accompanied by
an audible signal and the display of a message
(e.g. "Emissions fault: Starting prevented in
200 miles (300 km") indicating the remaining
range expressed in miles or kilometres.
Dashboard instruments

56
HeatingManual air conditioning
Temperature
F Turn the knob from blue
(cold) to red (hot) to adjust the
temperature to your wishes.
Air flow
F Turn the knob from position 1 to position 6 , to obtain
the desired air flow for your
comfort. If you place the air flow control at position
0 (off), the temperature in the vehicle will
no longer be maintained. A slight flow
of air can still be felt, resulting from the
for ward movement of the vehicle.
Adjusting the air
distribution
Windscreen and side windows.
Windscreen, side windows and
footwells.
Footwells.
Central and side air vents.
The air distribution can be
modulated by placing the knob at an
intermediate position.
Temperature
F Turn the knob from blue
(cold) to red (hot) to adjust the
temperature to your wishes.
Air flow
F Turn the knob from position 1 to position 6 , to obtain
the desired air flow for your
comfort.
1.
Adjusting the temperature.
2. Adjusting the air flow.
3. Adjusting the air distribution. 1.
Temperature adjustment.
2. Air flow adjustment.
3. Air distribution adjustment.
4. Air conditioning on/off.
Ease of use and comfort

58
Switching offF
P
ress the "empty fan" air flow
button until the fan symbol
disappears.
When the engine is cold, the air flow will
only reach its optimum level gradually
to prevent too much cold air being
distributed.
In cold weather, it favours the distribution
of warm air to the windscreen, the side
windows and the footwells only.
Temperature
The driver and front passenger can each set
the temperature to suit their requirements.
The value shown on the display is a level
of comfort, not a temperature in Celsius or
Fahrenheit. F

P
ush the button down (blue) to
reduce the value or up (red) to
increase it. A setting of around 21 provides optimum
comfort. Depending on your requirements, a
setting between 18 and 24 is normal.
In addition, it is recommended that you avoid a
left /right setting difference of more than 3.
For maximum cooling or heating of the
passenger compartment, it is possible
to exceed the minimum value 14 or the
maximum value 28. F
P
ush the button down until
"LO" is displayed or up until
"HI" is displayed.
On entering the vehicle, if the interior
temperature is much colder or warmer
than the comfort value setting, there is no
need to alter the value displayed in order
to reach the required level of comfort. The
system compensates automatically and
corrects the temperature difference as
quickly as possible.
Air conditioning
The air conditioning is designed to operate
efficiently in all seasons, with the windows
closed.
It allows you:
-
i
n summer, to lower the temperature,
-

i
n winter, above 3°C, to improve demisting.
Switching on F

P
ress the "A/C" button, the
associated indicator lamp
comes on.
The air conditioning cannot operate when the
air flow is set to off.
Switching off
F

P
ress the "A/C" button again;
the associated indicator lamp
goes off.
Switching off the air conditioning may
result in some discomfort (humidity,
mi st ing).
Ease of use and comfort

105
Observe the recommendations
on maintenance
Check the tyre pressures regularly, when cold,
referring to the label in the door aperture,
driver's side.
Carry out this check in particular:
-
b
efore a long journey,
-

a
t each change of season,
-

a
fter a long period out of use.
Do not forget the spare wheel and the tyres on
any trailer or caravan.
Have your vehicle ser viced regularly (engine
oil, oil filter, air filter, cabin filter, etc.) and
obser ve the schedule of operations in the
manufacturer's service schedule.
With a BlueHDi Diesel engine, if the SCR
system is faulty, your vehicle becomes
polluting. Visit as soon as possible a
PEUGEOT or a qualified workshop to make
your vehicle’s level of nitrogen oxide emissions
compliant to the standard.
When filling the tank, do not continue after the
3
rd cut-off of the nozzle to avoid over flow. At the wheel of your new vehicle, it is only after
the first 1,800
miles (3,000 kilometres) that you
will see the fuel consumption settle down to a
consistent average.
Driving recommendations
Observe the driving regulations and remain
vigilant whatever the traffic conditions.
Pay close attention to the traffic and keep your
hands on the wheel so that you are ready to
react at any time to any eventuality.
As a safety measure, the driver should only
carry out any operations that require close
attention when the vehicle is stationary.
On a long journey, a break every two hours is
strongly recommended.
In bad weather, drive smoothly, anticipate the
need to brake and increase the distance from
other vehicles.
Never leave the engine running in
an enclosed area without adequate
ventilation: internal combustion engines
emit toxic exhaust gases, such as carbon
monoxide. There is a risk of poisoning and
death!
In very severe wintry conditions
(temperatures below -23°C), to guarantee
correct operation and the longevity of
the mechanical elements of your vehicle,
engine and gearbox, the engine must be
left running for 4
minutes before driving.
6
Driving

117
On BlueHDi Diesel versions with manual
gearbox, in certain driving conditions the
system may suggest changing into neutral so
that the engine can go into standby (STOP
mode with Stop & Start). In this case, N is
displayed in the instrument panel.Example:
-

Y
ou are in third gear.
-

Y
ou press the accelerator pedal.
-

T
he system may suggest that you engage a
higher gear.
The system adapts its gear shift
recommendation according to the driving
conditions (slope, load, etc.) and the
driver’s requirements (power, acceleration,
b r a k i n g , e t c .) .
The system never suggests:
-
e

ngaging first gear,
-
enga

ging reverse gear,
-
enga

ging a lower gear. On vehicle fitted with a manual gearbox,
the arrow may be accompanied by the
gear recommended.Hill start assist
System that holds your vehicle for around
2
seconds, the time to move your foot from the
brake pedal to the accelerator.
The hill start assist function cannot be
deactivated. However, use of the parking
brake to immobilise the vehicle interrupts
its function.
The information appears on the instrument
panel in the form of an arrow.
Uphill, with the vehicle stationar y, it will
briefly stop the vehicle from rolling back
when you release the brake pedal.
With an electronic gearbox, if you are in
position A.
With an automatic gearbox, if you are in D .
6
Driving

118
Hill start assist is only available when:
- y our foot on the brake pedal fully
immobilises the vehicle,
-

c
ertain conditions of gradient are met,
-

w
ith the driver’s door closed.
Downhill, with the vehicle stationary and
reverse gear engaged, the vehicle is held
for a shor t time when you release the brake
pedal.
Do not leave the vehicle while it is being
held temporarily by hill start assist.
If you need to leave the vehicle with the
engine running, apply the parking brake
manually. Then ensure that the parking
brake warning lamp lights up constantly on
the instrument panel.
Operating fault
The fixed illumination of these
warning lamps indicates a fault with
the system.
Have the system checked by a
PEUGEOT dealer or a qualified
workshop.
Stop & Start
The system puts the engine temporarily into
standby – STOP mode – during stops in the
traffic (red lights, traffic jams, etc.). The engine
restarts automatically – START mode – as
soon as you wish to leave again. Restarting
occurs instantaneously, quickly and silently.
Per fect for urban use, the Stop & Start system
reduces fuel consumption and exhaust
emissions as well as the noise level when
stationary.
STOP mode
The " ECO" warning lamp illuminates
in the instrument panel and the
engine goes into standby.
With e- HDi or BlueHDi Diesel and an
electronic gearbox :
-

S

peed below 4 mph (6 km/h).
-

G

ear lever in position N.
Or
-
B

rake pedal pressed.
Driving

119
With BlueHDi Diesel and a manual gearbox:
- A s soon as the vehicle stops or the speed is
less than 2
mph (3 km/h) (with 1.5 Blue HDi
engine).
-

G
ear lever in neutral and clutch pedal
released.
With PureTech petrol and a manual,
electronic or automatic gearbox :
-

A
s soon as the vehicle stops or the speed
is less than 2
mph (3 km/h) (with manual
gearbox and depending on which version
you have).
-

G
ear lever in neutral and clutch pedal
released (manual gearbox).
-

B
rake pedal pressed or gear lever in
position N (electronic or automatic gearbox).
Special cases: STOP mode not
available
STOP mode is not invoked when:
- t he driver's door is open,
-

t
he driver's seat belt is not fastened,
-

t
he vehicle has not exceeded 6 mph
(10
km/h) since the last engine start using
t h e key,
-

t
he engine is needed to maintain a
comfortable temperature in the passenger
compartment,
-

d
emisting is active, The ECO warning lamp flashes for a
few seconds, then goes off.
This operation is perfectly normal.
A time counter sums up the time
periods spent in STOP mode
during a journey. It resets every
time the ignition is switched on
using the key.
For your comfort, during parking
manoeuvres, STOP mode is not available
for a few seconds after coming out of
reverse gear.
The Stop & Start system does not affect
the functionality of the vehicle, such as for
example, braking, power steering, With a manual gearbox in STOP mode, if
a gear is engaged without fully depressing
the clutch pedal, a warning lamp comes
on or an alert message is displayed asking
you to depress the clutch pedal to restart
the engine.
Never refuel with the engine in STOP
mode; you must switch off the ignition
using the key.
START mode
The ECO warning lamp goes off and
the engine starts:
With a manual gearbox :
-

C

lutch pedal depressed.
With an electronic / automatic gearbox :
-

G

ear lever in position A / D or M .
-
B

rake pedal released.
or
-
s

ome special conditions (battery charge,
engine temperature, braking assistance,
exterior temperature, etc.) where the engine
is needed to control the system.
6
Driving

124
Registering a cruise speed
setting
- Bring the vehicle up to the desired speed by pressing the accelerator.
-

P
ress the SET – or
SET + button.
The speed setting is registered/activated and
the vehicle will maintain this speed.
Temporarily exceeding the
programmed speed
It is possible to accelerate and
temporarily drive at a speed higher
than the registered speed setting.
The cruise speed setting value
flashes.
When the accelerator pedal is
released, the vehicle will return to
the registered speed setting.
Pause (OFF)
- Press this button or the brake or clutch pedal (depending on the version). With 1.2 PureTech 82 and 110 (Euro
6.2)
or 1.5 BlueHDi (Euro 6.2) engines, a
manual gearbox and the Stop & Start,
pressing the clutch pedal does not pause
the cruise control, the cruise control
remains active after changing gears.
Resume
- After the cruise control has been paused, press this button.
The vehicle returns to the last registered speed.
Alternatively, you can also resume the
procedure for "Registering a cruise speed
setting".
Driving

130
In bad or wintry weather, ensure that the
sensors are not covered with mud, ice or
snow.
The system will be deactivated
automatically if a trailer is being towed or if
a bicycle carrier is fitted (vehicle fitted with
a towbar or bicycle carrier recommended
by PEUGEOT).
The parking sensor system cannot in
any circumstances replace the need for
vigilance on the part of the driver.Reversing camera
The reversing camera is activated automatically
when reverse gear is engaged.
The image is displayed on the touch screen.
The reversing camera function may be
supplemented with parking sensors.They are represented by lines marked "on
the ground" and do not allow the position of
the vehicle to be determined relative to tall
obstacles (for example: other vehicles, etc.).
Some deformation of the image is normal.
The blue lines represent the general direction
of the vehicle (the gap represents the width of
your vehicle except for the door mirrors).
The red lines represent a distance of about
30
cm beyond the edge of your vehicle's rear
b u m p e r.
The green lines represent distances of about 1
and 2 metres beyond the edge of your vehicle's
rear bumper.
The superimposed representation of guide
lines helps with the manoeuvre. The reversing camera cannot, in any
circumstances, replace the need for
vigilance on the part of the driver.
High pressure jet wash
When washing your vehicle, do not direct
the lance within 30
cm of the camera lens.
Opening the tailgate causes the display to
disappear.
Clean the reversing camera regularly
using a soft, dry cloth.
Driving