check engine Peugeot 208 2017 User Guide

55
Recommendations for ventilation and air conditioning
In order for these systems to be fully effective,
follow the operation and maintenance
guidelines below:
F
T
o ensure that the air is distributed evenly,
keep the external air intake grilles at the
base of the windscreen, the nozzles, the
vents, the air outlets and the air extractor
in the boot free from obstructions.
F

D
o not cover the sunshine sensor,
located on the dashboard; this is used for
regulation of the automatic air conditioning
system.
F

O
perate the air conditioning system for
at least 5 to 10
minutes, once or twice a
month to keep it in per fect working order.
F

E
nsure that the passenger compartment
filter is in good condition and replace
the filter elements periodically. We
recommend the use of a combined
passenger compartment filter. Thanks to
its special active additive, it helps both to
purify the air breathed by the occupants
and to keep the passenger compartment
clean (reduction of allergic symptoms, bad
odours and greasy deposits). F
T o ensure correct operation of the
air conditioning system, you are also
advised to have it checked regularly
as recommended in the Warranty and
Maintenance Record.
F

I
f the system does not produce cold air,
switch it off and contact a PEUGEOT
dealer or a qualified workshop.
When towing the maximum load on a steep
gradient in high temperatures, switching off
the air conditioning increases the available
engine power and so improves the towing
ability.
To avoid the windows misting up and
deterioration in the quality of the air:
-

d
o not drive for too long with the
ventilation switched off.
-

d
o not keep air recirculation set for an
extended period. If after an extended stop in sunshine,
the interior temperature is very high, first
ventilate the passenger compartment for
a few moments.
Put the air flow control at a setting high
enough to quickly change the air in the
passenger compartment.
The condensation created by the air
conditioning results in a discharge of
water under the vehicle which is per fectly
normal.
Stop & Star t
The heating and air conditioning systems
only work when the engine is running.
To maintain a comfortable temperature
in the passenger compartment, you may
temporarily deactivate the Stop & Start
system.
For more information on Stop & Star t ,
refer to the corresponding section.
3
Ease of use and comfort

78
If you purchased your vehicle outside the
Brand network, we invite you to have the
configuration of these ser vices checked
and, if desired, have a dealer change it to
suit your wishes. In a multilingual country,
configuration is possible in the official
national language of your choice.
For technical reasons, particularly
to improve the quality of PEUGEOT
CONNECT ser vices to customers, the
manufacturer reser ves the right to carry
out updates to the vehicle's on-board
telematic system.Electronic stability control
(ESC)
Electronic stability control (ESC) comprising
the following systems:
-
a
nti-lock braking system (ABS) and
electronic brake force distribution (EBFD),
-
em

ergency braking assistance (EBA),
-

w
heel anti-slip regulation (ASR) or traction
control,
-
d

ynamic stability control (DSC). It is triggered in relation to the speed at which
the brake pedal is pressed. This is felt by a
reduction in the resistance of the pedal and an
increase in the effectiveness of the braking.
Anti-slip regulation (ASR)
The ASR system (also known as Traction
Control) optimises traction in order to limit
wheel slip by acting on the brakes of the driving
wheels and on the engine. It also improves
the directional stability of the vehicle on
acceleration.
Dynamic stability control (DSC)
If there is a difference between the path
followed by the vehicle and that required by
the driver, the DSC monitors each wheel and
automatically acts on the brake of one or more
wheels and on the engine to return the vehicle
to the required path, within the limits of the laws
of physics.
Definitions
Anti-lock braking system (ABS)
and electronic brake force
distribution (EBFD)
This system improves the stability and
manoeuvrability of your vehicle when braking
and contributes towards improved control on
corners, in particular on poor or slippery road
surfaces.
The ABS prevents wheel lock in the event of
emergency braking.
The electronic brake force distribution system
manages the braking pressure wheel by wheel.
Emergency braking assistance
(EBA)
In an emergency, this system enables you to
reach the optimum braking pressure more
quickly and therefore reduce the stopping
distance.
Safety

79
Anti-lock braking system
(ABS) and electronic brake
force distribution (EBD)
When lit up fixed, this warning lamp
indicates a fault with the ABS.
The vehicle retains conventional braking. Drive
carefully at moderate speed. If this warning lamp comes on, in
conjunction with the STOP and ABS
warning lamps, an audible signal
and a message, it means that the
electronic brake force distribution
(EBD) is defective.
When changing wheels (tyres and rims),
ensure that these are approved for your
vehicle.
When operating under normal conditions,
the ABS may cause the brake pedal to
vibrate slightly. In emergency braking, press the brake
pedal hard and maintain this pressure.
Anti-slip regulation (ASR)
/ Dynamic stability control
(DSC)
Operation
They come into operation in the event of a
problem with grip or trajectory.
This is indicated by this warning
lamp flashing in the instrument
panel.
These systems are activated automatically
every time the vehicle is started.
Deactivation
You must stop the vehicle as soon as it is
safe to do so.
In both cases, have the system checked by a
PEUGEOT dealer or a qualified workshop as
soon as possible. In exceptional conditions (starting a vehicle
which is bogged down, stuck in snow, on soft
ground, etc.), it may be advisable to deactivate
these systems, so that the wheels can turn
freely and regain grip.
Reactivate the systems as soon as the level of
grip permits.
Deactivating using the button
F P ress this button.
The button indicator lamp comes on.
The ASR and DSC systems will no longer have
an effect on engine operation or the brakes in
the event of an involuntary change of trajectory.
5
Safety

80
Reactivation
Deactivation can be configured in
the Driving / Vehicle menu.
It is confirmed by the display of a message.
These systems are reactivated automatically
each time the ignition is switched back on or
above 30

mph (50 km/h).
Below 30

mph (50 km/h), you can reactivate
them manually.
For the 1.6 THP 165 and THP 208 petrol
engines, the reactivation must always be
carried out manually.
Reactivating using the button F

P
ress this button again to
reactivate manually.
The indicator lamp in the button goes off. Reactivating using the touch screen
Reactivation can be configured in
the Driving / Vehicle menu.
It is confirmed by the display of a message.
Operating fault
Illumination of this warning lamp,
accompanied by the display of a
message and an audible signal,
indicates a fault with the system.
Contact a PEUGEOT dealer or a qualified
workshop to have the systems checked. ASR / DSC
These systems offer increased safety
in normal driving, but they should not
encourage the driver to take extra risks or
drive at high speed.
It is in conditions of reduced grip (rain,
snow, black ice) that the risk of loss of grip
increases. It is therefore important for your
safety to keep these systems activated in
all conditions, and particularly in difficult
conditions.
The correct operation of these
systems depends on obser vation of
the manufacturer's recommendations
regarding as much the wheels (tyres and
rims), braking and electronic components
as the assembly and repair procedures
used by PEUGEOT dealers.
The use of snow tyres is recommended,
in order to be able to benefit from the
efficiency of these systems in winter
conditions.
In this case, it is essential to equip the
four wheels with tyres approved for your
vehicle.
Deactivating using the touch screen
The systems no longer have an effect on
engine operation.
Safety

105
Observe the recommendations
on maintenance
Check the tyre pressures regularly, when cold,
referring to the label in the door aperture,
driver's side.
Carry out this check in particular:
-
b
efore a long journey,
-

a
t each change of season,
-

a
fter a long period out of use.
Do not forget the spare wheel and the tyres on
any trailer or caravan.
Have your vehicle ser viced regularly (engine
oil, oil filter, air filter, cabin filter, etc.) and
obser ve the schedule of operations in the
manufacturer's service schedule.
With a BlueHDi Diesel engine, if the SCR
system is faulty, your vehicle becomes
polluting. Visit as soon as possible a
PEUGEOT or a qualified workshop to make
your vehicle’s level of nitrogen oxide emissions
compliant to the standard.
When filling the tank, do not continue after the
3
rd cut-off of the nozzle to avoid over flow. At the wheel of your new vehicle, it is only after
the first 1,800
miles (3,000 kilometres) that you
will see the fuel consumption settle down to a
consistent average.
Driving recommendations
Observe the driving regulations and remain
vigilant whatever the traffic conditions.
Pay close attention to the traffic and keep your
hands on the wheel so that you are ready to
react at any time to any eventuality.
As a safety measure, the driver should only
carry out any operations that require close
attention when the vehicle is stationary.
On a long journey, a break every two hours is
strongly recommended.
In bad weather, drive smoothly, anticipate the
need to brake and increase the distance from
other vehicles.
Never leave the engine running in
an enclosed area without adequate
ventilation: internal combustion engines
emit toxic exhaust gases, such as carbon
monoxide. There is a risk of poisoning and
death!
In very severe wintry conditions
(temperatures below -23°C), to guarantee
correct operation and the longevity of
the mechanical elements of your vehicle,
engine and gearbox, the engine must be
left running for 4
minutes before driving.
6
Driving

107
F Take into account the increased sensitivity to wind.
Cooling
Towing a trailer on a slope increases the
temperature of the coolant.
As the fan is electrically controlled, its cooling
capacity is not dependent on the engine speed.
F

T
o lower the engine speed, reduce your
speed.
The maximum towable load on an incline
depends on the gradient and the exterior
temperature.
In all cases, keep a check on the coolant
temperature.
F

I
f this warning lamp and the
STOP warning lamp come on,
stop the vehicle and switch off
the engine as soon as possible.
New vehicle
Do not pull a trailer before having driven at
least 600
miles (1,000 kilometres).
Braking
Towing a trailer increases the braking distance.
To avoid overheating of the brakes, the use of
engine braking is recommended.
Ty r e s
F Check the tyre pressures of the towing vehicle and of the trailer, observing the
recommended pressures.
Lighting
F Check the electrical lighting and signalling on the trailer and the headlamp beam height
of your vehicle.
For more information on Adjusting the
headlamp beam height , refer to the
corresponding section.
The rear parking sensors will be
deactivated automatically to avoid the
audible signal if a genuine PEUGEOT
towbar is used. If the exterior temperature is high, it is
recommended that the engine be allowed
to idle for 1 to 2
minutes after the vehicle
comes to a stop, to facilitate its cooling.
Side wind
6
Driving

110
Parking brake
Releasing
F Pull the parking brake lever up slightly, press the release button then lower the
lever fully.
When the vehicle is being driven,
if this warning lamp and the
STOP warning lamp come on,
accompanied by an audible signal
and a message on the screen, this
indicates that the parking brake
is still on or has not been fully
released. Remember to fully lower
the parking brake lever.
Applying
F Pull the lever up to immobilise your vehicle.
When parking on a steep slope, direct
your wheels against the kerb, apply the
parking brake, engage a gear opposite
to the direction the vehicle is facing and
switch off the ignition.
On return to the vehicle, remember that
a gear had been engaged before starting
the engine. If excessive travel or a loss of
effectiveness of this system is noticed,
the parking brake must be checked, even
between two services.
Checks of this safety-related system must
be carried by a PEUGEOT dealer or a
qualified workshop.
Driving

113
Manual mode
This mode allows manual sequential gear
changing.
F
M
ove the selector lever to M .
F

P
ush the lever for ward to change
up.
F

P
ull the lever back to change
down.
Steering mounted control paddles
F Pull the "+" paddle to change up.
F P ull the "-" paddle to change up.
The gear engaged is indicated in the display.
Creep function
Depending on the engine, the vehicle moves
without pressing the accelerator.
Assistance with low-speed
manoeuvres
With the engine running at idle, parking brake
released and the lever placed at A , M or R, the
vehicle moves off when your release the brake
pedal.
It stops on opening the driver's door. Closing
the door, and putting your foot on the brake
or accelerator pedal allows movement of the
vehicle again. Following disconnection of the battery, you
have to reinitialise the gearbox.
F

S
witch on the ignition.
AUTO and – appear in the
instrument panel.
F
Sel
ect position N
.
F
P
ress the brake pedal firmly.
F
W
ait around 30 seconds until N or a gear
appears in the instrument panel.
F
R
elease the brake pedal.
The gearbox is operational again.
With the ignition on, if this warning
lamp comes on and AUTO flashes,
accompanied by an audible signal
and a message in the screen, this
indicates a gearbox fault.
Have it checked by a PEUGEOT dealer or a
qualified workshop.
6
Driving

118
Hill start assist is only available when:
- y our foot on the brake pedal fully
immobilises the vehicle,
-

c
ertain conditions of gradient are met,
-

w
ith the driver’s door closed.
Downhill, with the vehicle stationary and
reverse gear engaged, the vehicle is held
for a shor t time when you release the brake
pedal.
Do not leave the vehicle while it is being
held temporarily by hill start assist.
If you need to leave the vehicle with the
engine running, apply the parking brake
manually. Then ensure that the parking
brake warning lamp lights up constantly on
the instrument panel.
Operating fault
The fixed illumination of these
warning lamps indicates a fault with
the system.
Have the system checked by a
PEUGEOT dealer or a qualified
workshop.
Stop & Start
The system puts the engine temporarily into
standby – STOP mode – during stops in the
traffic (red lights, traffic jams, etc.). The engine
restarts automatically – START mode – as
soon as you wish to leave again. Restarting
occurs instantaneously, quickly and silently.
Per fect for urban use, the Stop & Start system
reduces fuel consumption and exhaust
emissions as well as the noise level when
stationary.
STOP mode
The " ECO" warning lamp illuminates
in the instrument panel and the
engine goes into standby.
With e- HDi or BlueHDi Diesel and an
electronic gearbox :
-

S

peed below 4 mph (6 km/h).
-

G

ear lever in position N.
Or
-
B

rake pedal pressed.
Driving

121
Operating fault
In the event of a fault with the system, the ECO
OFF switch warning lamp flashes then comes
on fixed.
Have it checked by a PEUGEOT dealer or a
qualified workshop.
If a fault occurs in STOP mode, the vehicle
may stall. All of the instrument panel warning
lamps come on. It is then necessary to switch
the ignition off and to restart the engine using
t h e key.The Stop & Start system requires a
12
V battery of specific technology and
specification.
All work on this type of battery must be
carried out only by a PEUGEOT dealer or
a qualified workshop.
For more information on the 12
V batter y,
refer to the corresponding section.
Speed limiter "LIMIT"
The system prevents the vehicle from
exceeding the speed setting programmed by
the driver.
Steering mounted controls
1. Speed limiter mode selection / off.
2. Increases the set value.
3. Decreases the set value.
4. Speed limiter On / Pause. The vehicle responds to the accelerator until
resistance is felt in the pedal, which signifies
that the vehicle has reached the limiter speed
setting.
However, pressing the pedal beyond this point
of resistance to the floor permits exceeding
of the programmed speed. To resume use of
the limiter, simply reduce the pressure on the
accelerator pedal gradually and return to a
speed below that programmed.
Setting and operation of the system can be
done stationar y with the engine running or
when driving.
Selection
F Place the thumbwheel at the "LIMIT"

position: the speed limiter mode is selected
but is not switched on (PAUSE).
Switching the speed limiter on is not required to
set the speed limit.
The speed setting is selected with the engine
running, stationary or when driving. The
minimum speed setting possible is 20

mph
(30


km/h).
6
Driving