warning Peugeot 208 2019 User Guide

16
Warning/indicator lampStateCause Actions/Observations
AdBlue
®
(with
1.6 BlueHDi
E u r o 6 .1)Fixed, on switching
on the ignition,
accompanied by an
audible signal and
a
message indicating the
remaining driving range.The remaining driving range is
between 1,500 and 375 miles
(2,400
and 600 km). Top up the AdBlue® as soon as possible, or carry out
(3).
+ AdBlue
® warning
lamp flashing and
Service warning lamp
fixed, accompanied
by an audible signal
and a

message
indicating the
remaining driving
range. The driving range is less than
375
miles (600 km).Yo u must
top up the AdBlue® to avoid a breakdown ,
or carry out (3).
AdBlue
® warning
lamp flashing and
Service warning lamp
fixed, accompanied
by an audible signal
and a

message
indicating that starting
is prevented. The AdBlue® tank is empty: the
starting prevention system required
by legislation prevents starting of the
engine. To restart the engine, top up the AdBlue®, or carry
out (2).
It is essential to add at least 5

litres of AdBlue
® to its
tank.
(2): Contact a

PEUGEOT dealer or a

qualified
workshop. (3)
: Go to a

PEUGEOT dealer or a

qualified
workshop.
Instruments

17
Warning/indicator lampStateCause Actions/Observations
AdBlue
®
(with 1.5 BlueHDi
Euro 6.2) On for around
30
seconds when
starting the vehicle,
accompanied by
a
message indicating
the remaining driving
range. The remaining driving range is
between 1,500
and 500 miles
(2,400 and 800 km).Top up the AdBlue
®.
Fixed, on switching
on the ignition,
accompanied by an
audible signal and
a
message indicating the
remaining driving range.The remaining driving range is
between 500 and 60 miles (800 and
10 0 k m).Top up the AdBlue® as soon as possible , or carry out (3).
Flashing,
accompanied by an
audible signal and
a
message indicating
the remaining driving
range. The driving range is less than
60
miles (100 km).Yo u must
top up the AdBlue® to avoid star ting being
prevented , or carry out (3).
Flashing,
accompanied by an
audible signal and
a

message indicating
that starting is
prevented. The AdBlue
® tank is empty: the
starting prevention system required
by legislation prevents starting of the
engine.To restart the engine, top up the AdBlue® or carry out (2).
It is essential to add at least 5

litres of AdBlue® to its
tank.
1
Instruments

18
Warning/indicator lampStateCause Actions/Observations
+
+ SCR emissions
control system
Fixed when the ignition is
switched on, accompanied
by an audible signal and
a


message.A fault with the SCR emissions
control system has been detected. This alert disappears once the exhaust emissions
return to normal levels.
AdBlue
® warning
lamp flashing, on
switching on the
ignition, associated
with the fixed Ser vice
and Engine-diagnostic
warning lamps,
accompanied by an
audible signal and
a

message indicating
the remaining driving
range. Depending on the message
displayed, you can continue driving
for up to 685
miles (1,100 km) before
the engine starting prevention system
is triggered. Carry out (3) as soon as possible to avoid star ting
being prevented
.
AdBlue
® warning
lamp flashing, on
switching on the
ignition, associated
with the fixed Ser vice
and Engine-diagnostic
warning lamps,
accompanied by an
audible signal and
a


message. An engine immobiliser prevents
the engine from restarting (over
the authorised driving limit after
confirmation of a
fault with the
emissions control system). To start the engine, carry out (2).
Rear foglamp Fixed. The lamp is on.
Instruments

19
Warning/indicator lampStateCause Actions/Observations
Green warning/indicator lamps
Stop & Star tFixed.When the vehicle stops, the Stop &
Start puts the engine into STOP mode.
Flashing temporarily. STOP mode is momentarily
unavailable or START mode is
automatically triggered.
Automatic
wiping Fixed.
Automatic windscreen wiping is
activated.
Front foglamps Fixed. The front foglamps are on.
Direction
indicators Flashing with audible
signal. The direction indicators are on.
Sidelamps Fixed. The lamps are on.
Dipped beam
headlamps Fixed.
The lamps are on.
Blue warning/indicator lamps
Main beam
headlampsFixed.
The lamps are on.
1
Instruments

20
Indicators
Service indicator
The ser vice indicator is displayed in the
instrument panel. Depending on the vehicle
version:
-
t
he distance recorder display line indicates
the distance remaining before the next
ser vice is due, or the distance travelled
since it was due preceded by the "-" sign.
Warning/indicator
lamp State
CauseActions/
Observations
Ser vice
spanner Lights up temporarily
when the ignition is
switched on.
Between 620 and
1 ,860 miles (1,000 and
3,000
km) remain before
the next ser vice is due.
Fixed, when the
ignition is switched on. The ser vice is due in
less than 620
miles
(1,000


km).Have your vehicle
serviced very soon.
+ Ser vice
spanner
flashing
Flashing then fixed,
when the ignition is
switched on.
(For BlueHDi Diesel
versions, associated
with the Ser vice
warning lamp). The servicing interval
has been exceeded.
Have your vehicle
ser viced as soon as
possible.
The distance indicated (in miles or
kilometres) is calculated according to the
distance covered and the time elapsed
since the last ser vice.
The alert may also be triggered close to
a
due date.
-
a
n alert message indicates the distance
remaining, as well as the period before
the next ser vice is due or how long it is
overdue.
Resetting the service indicator
The ser vice indicator must be reset after each
service.
If you have carried out the ser vice on your
vehicle yourself:
F

s
witch off the ignition,
If you have to disconnect the battery
following this operation, lock the vehicle
and wait at least 5
minutes for the reset to
be registered.
F

p
ress and hold the trip distance recorder
reset button,
F

s
witch on the ignition; the distance recorder
display begins a


countdown,
F

r
elease the button when " =0" is displayed;
the spanner disappears.
Instruments

21
Retrieving the service
information
You can access the ser vice information at any
time.
F
P
ress the trip distance recorder reset
button.
T

he ser vice information is displayed for
a


few seconds, then disappears.
Engine oil level indicator
(depending on version)
On versions fitted with an electric oil level
indicator, the state of the engine oil level is
displayed in the instrument panel for a few
seconds, after the servicing information.
The level read will only be correct if the
vehicle is on level ground and the engine
has been off for more than 30
minutes.
Oil level insufficient
This is indicated by the display of the message
"Oil level incorrect" in the instrument panel,
accompanied by the Ser vice warning lamp and
an audible signal.
Oil level indicator fault
This is signalled by the display of the message
"Oil level measurement invalid" in the
instrument panel.
Contact a PEUGEOT dealer or a qualified
workshop.
In the event of a
fault with the electric
indicator, the oil level is no longer
monitored.
If the system is faulty, you must check the
engine oil level using the manual dipstick
located under the bonnet.
For more information on Checking levels ,
refer to the corresponding section.
Engine coolant temperature
With the engine running, when the needle is:
- i n zone A , the temperature of the engine
coolant is correct, -

i
n zone B
, the temperature of the engine
coolant is too high; the maximum
temperature and the central STOP warning
lamps come on, accompanied by an
audible signal and a

warning message in
the screen.
You must stop as soon as it is safe to do so.
Wait a few minutes before switching off the
engine.
Contact a PEUGEOT dealer or a qualified
workshop. If the low oil level is confirmed by a check using
the dipstick, the level must be topped up to
avoid damage to the engine.
For more information on Checking levels ,
refer to the corresponding section.
1
Instruments

22
Remaining range between 1,500 and 500 miles
( 2,400 and 800 km) (1.5 BlueHDi Euro 6.2)
Remaining range between 1,500
and 375 miles
(2,400
and 600 km) (1.6 BlueHDi Euro 6.1)Remaining range between 500 and 60 miles
( 800 and 100 km) (1.5 BlueHDi Euro 6.2)
Remaining range less than 375
miles
(600
km) (1.6 BlueHDi Euro 6.1)
When switching on the ignition, this warning lamp
comes on for about thirty seconds, accompanied
by an audible signal and the display of a message
("Top up AdBlue: Starting impossible in x miles")
indicating the remaining range expressed in miles
or kilometres.
The reser ve level has been reached; it is
recommended that you top up as soon as
possible.
When switching on the ignition, this warning
lamp comes on, accompanied by an audible
signal and the display of a
message ("Top
up AdBlue: Starting impossible in x miles")
indicating the remaining range expressed in
miles or kilometres.
When driving, the message is displayed
approximately every 185
miles (300 km) until
the level is topped up.
The reser ve level has been reached; it is
recommended that you top up as soon as
possible. When switching on the ignition, this warning
lamp comes on, accompanied by an audible
signal (1
beep) and the display of a message
("Top up AdBlue: Starting impossible in
x miles") indicating the remaining range
expressed in miles or kilometres.
When driving, the audible signal and the
message display are triggered every 60 miles
(100 km) until the level is topped up.
It is essential to top up as soon as possible and
before the tank is completely empty; other wise
it will not be possible to restart the engine after
the next stop.
When switching on the ignition, this warning
lamp flashes, accompanied by the permanent
lighting of the Ser vice warning lamp, an audible
signal and the display of a
message ("Top
up AdBlue: Starting impossible in x miles")
indicating the remaining range expressed in
miles or kilometres.
When driving, this message is displayed every
30
seconds until the AdBlue level has been
topped up.
AdBlue® range indicators
These range indicators are present only on
BlueHDi Diesel versions.
Once the AdBlue
® tank is on reser ve or after
detection of a

fault with the SCR emissions
control system, when the ignition is switched
on, an indicator displays an estimate of the
distance that can be covered, the range, before
engine starting is prevented.
In the event of the risk of non-
starting related to a lack of
AdBlue
®
The engine starting prevention system
required by regulations is activated
automatically once the AdBlue
® tank is
e m pt y.
Range greater than 1,500

miles (2,400 km)
When the ignition is switched on, no
information on range is displayed automatically
in the instrument panel.
Pressing this button
temporarily displays the
driving range.
Instruments

23
Remaining range less than 60 miles
( 100 km) (1.5 BlueHDi Euro 6.2)
When driving, the audible signal and the
message display are triggered every 6
miles
(10
km) until the AdBlue tank is topped up.
It is essential to top up as soon as possible and
before the tank is completely empty; other wise
it will not be possible to restart the engine after
the next stop.
Breakdown related to a
lack of AdBlue
®
The AdBlue® tank is empty: the starting
prevention system required by legislation
prevents starting of the engine. It is essential to top up as soon as possible and
before the tank is completely empty; other wise
it will not be possible to restart the engine after
the next stop.
When switching on the ignition, this warning
lamp flashes, accompanied by an audible
signal (1

beep) and the display of a message
("Top up AdBlue: Starting impossible in
x miles") indicating the remaining range
expressed in miles or kilometres.
When switching on the ignition, this warning
lamp flashes, accompanied by an audible
signal and the display of the message "Top up
AdBlue: Starting impossible". To be able to restart the engine, it is
essential to add at least 5 litres of AdBlue
®
to its tank.
For more information on AdBlue
®
(BlueHDi engines) , and, in particular,
on topping up, refer to the corresponding
section.
In the event of a fault with the
S CR emissions control system
A system that prevents engine starting is
activated automatically from 685
miles
(1,100
km) after confirmation of a fault with
the SCR emissions control system.
Have the system checked by a
PEUGEOT
dealer or a
qualified workshop as soon as
possible.
In the event of the detection of a
faultIf it is a
temporary fault, the alert
disappears during the next journey, after
self-diagnosis of the SCR system.
During the permitted driving phase
(between 685 and 0 miles (1,100 and 0 km))
These warning lamps come on, accompanied
by an audible signal and the display of the
message "Emissions fault".
The alert is triggered when driving when the
fault is detected for the first time, then when switching on the ignition for subsequent
journeys, while the fault persists.
If a
fault with the SCR system is confirmed
(after 31
miles (50 km) covered with the
permanent display of the message signalling
a
fault), these warning lamps come on and the
AdBlue warning lamp flashes, accompanied by
an audible signal and the display of a
message
(e.g. "Emissions fault: Starting prevented in
185
miles") indicating the remaining range in
miles or kilometres.
While driving, the message is displayed every
30
seconds while the fault with the SCR
emissions control system persists.
The alert is repeated when switching on the
ignition.
You should go to a
PEUGEOT dealer or
a
qualified workshop as soon as possible.
Other wise you will not be able to restart the
vehicle.
1
Instruments

24
Starting preventedYou have exceeded the authorised driving
limit: the starting prevention system does
not allow the engine to be started.
To be able to restart the engine, you must call
on a
PEUGEOT dealer or a qualified workshop.
Each time the ignition is switched on, these
warning lamps come on and the AdBlue
warning lamp flashes, accompanied by an
audible signal and the display of the message
"Emissions fault: Starting prevented".
Trip computer
Instrument panel screen
F Each press on the end of the wiper
control stalk displays the information in
turn. -
Trip
1 with:
•
t
he average speed,
•
t
he average fuel consumption,
•
t
he distance travelled,
for the first trip.
- Trip
2 with:
•
t
he average speed,
•
t
he average fuel consumption,
•
t
he distance travelled,
for the second trip.
-
T
he current information with:
•
t
he range,
•
t
he current fuel consumption,
•
t
he Stop & Start time counter.
With touch screen
The information is accessible via the
Driving/Vehicle
.
Reset trip
F When the desired trip is displayed, press
the button located on the end of the wiper
control stalk for more than 2
seconds.
Trips 1
and 2 are independent and are used
identically.
For example, trip 1
can be used for daily figures
and trip 2
for monthly figures.
Display of information on the touch screen
Instruments

31
F Turn the key towards the rear again within 5 seconds to deadlock the vehicle.
Lighting of the direction indicators for a
few
seconds confirms that the procedure has
completed correctly.
If your vehicle is fitted with an alarm, this
function will not be activated when locking
with the key.
If the alarm is activated, the siren sounds
on opening the door; switch on the ignition
to stop it.
Central locking not
functioning
Use these procedures in the following cases:
- c entral locking fault,
-
b

attery disconnected or discharged.
In the event of a
malfunction with the
central locking system, the battery must
be disconnected to lock the boot and thus
ensure that the vehicle is locked fully.
Driver's door
F Turn the key towards the rear of the vehicle to lock it, or towards the front to unlock it.
Passenger doors
Unlocking
F P ull the interior door opening handle.
Locking
F

O
pen the door.
F

F
or the rear doors, check that the child lock
is not activated. Refer to the corresponding
section.
F

R
emove the black cap, located on the edge
of the door, using the key.
F

I
nsert the key into the hole without forcing
it; then, without turning it, move the latch
sideways towards the inside of the door.
F

R
emove the key and refit the black cap.
F

C
lose the doors and check from the
outside that the vehicle is locked.
Changing the battery
If the battery is flat, you are informed
by illumination of this warning lamp,
an audible signal and a
message in
the screen. Batter y ref.: CR1620/3
volts.
F
U
nclip the cover by inserting a small
screwdriver in the slot and raise the cover.
F
R
emove the discharged battery from its
housing.
F
I
nsert the new battery, observing the
polarity, and clip the cover onto the
housing.
F
R
einitialise the remote control.
For more information on Reinitialising the
remote control , refer to the corresponding
section.
Do not throw remote control batteries
away as they contain metals which are
harmful to the environment. Take them
to an approved collection point.
2
Access