warning Peugeot 208 2019 Owner's Guide

82
F Insert the key into the ignition switch.
The system recognises the starting code.
F Unlock the steering column by simultaneously turning the steering wheel and the key.
In some cases, you may have to apply
some force to turn the steering wheel (if
the wheels are on full lock against a
kerb,
for example).
F

T
urn the key all the way towards the
dashboard to position 3


(Starting).
F

W
hen the engine starts, release the key.
With Petrol engines , after a
cold start,
preheating the catalytic converter can
cause clearly-felt engine vibrations when
stationary, with the engine running, for
anything up to 2
minutes (accelerated idle
speed).
Electronic immobiliser
The original key contains a coded electronic
c hip. When the ignition is switched on, starting
is only possible if the code is detected and
recognised.
This anti-theft protection locks the engine
management system a
few moments after the
ignition is switched off and prevents starting of
the engine following a


break-in.
In the event of a
fault, you are
informed by the illumination of this
warning lamp, the emission of an
audible signal and the display of
a


message.
In this case, your vehicle will not start; contact
a
PEUGEOT dealer as soon as possible.
Switching off
F Immobilise the vehicle.
F T urn the key fully towards you to position
1


(Stop) .
F

R
emove the key from the ignition switch.
F

T
o lock the steering column, turn the
steering until it locks.
Free-wheeling
For safety reasons, do not free-wheel.
Other wise, some vehicle functions will no
longer be active. To facilitate unlocking of the steering
column, the front wheels should be
straight before switching off the engine.
Switching off the engine leads to a
loss of
braking assistance.
Key left in
If the key has been left in the ignition
switch at position 2

(Ignition on)
, the
ignition will be switched off automatically
after one hour.
To switch the ignition back on, turn the key
to position 1

(Stop)
, then back to position
2

(Ignition on)
.Parking brake
Releasing
Driving

83
F Pull the parking brake lever up slightly, press the release button then lower the
lever fully.
When the vehicle is being driven,
if this warning lamp and the STOP
warning lamp come on, accompanied
by an audible signal and a
message
on the screen, this indicates that the
parking brake is still applied or has
not been fully released. Remember
to fully lower the parking brake lever.
Applying
F Pull the lever up to immobilise your vehicle. When parking on a steep slope, direct
your wheels against the kerb, apply the
parking brake, engage a gear opposite
to the direction the vehicle is facing and
switch off the ignition.
On return to the vehicle, remember that
a gear had been engaged before starting
the engine.
If excessive travel or a loss of
effectiveness of this system is noticed,
the parking brake must be checked, even
between two services.
Checks of this safety-related system
must be carried by a PEUGEOT dealer or
a

qualified workshop.
Manual gearbox
5-speed
F Move the gear lever fully to the right to
engage 5th g e a r.
Engaging reverse gear
F Move the gear lever to the right then pull it back.
Only engage reverse gear when the
vehicle is stationary with the engine at idle.
6-speed
F Move the lever fully to the right to engage 5th
or 6th g e a r.
Engaging reverse gear
6
Driving

84
F Raise the collar below the gear lever knob, then push the lever fully to the left and then
forward.
Only engage reverse gear when the
vehicle is stationary with the engine at idle.
As a safety precaution and to aid engine
s tar t-up:
-

a
lways select neutral,
-

p
ress the clutch pedal.
The gear shift indicator is displayed in the
instrument panel.
Automatic gearbox (EAT6)
P. Parking.
R. Reverse.
N. Neutral.
Display in the instrument
panel
When you select a position with the lever,
t he corresponding lamp is displayed in the
instrument panel.
Foot on the brake warning
Press the brake pedal when this
warning lamp comes on in the
instrument panel.
Automatic mode
This mode allows gear changing without action
by the driver.
Starting
Parking brake applied.
F S tart the engine.
F

L
ever in position P or N .
F

F
ully depress the brake pedal.
F

R
elease the parking brake.
F

P
lace the selector at D or R .Never leave children unattended in the
vehicle when the engine is running.
F
Sel
ect position D for automatic
changing of
the gears.
D.
Drive – AUTO driving mode.
M. Manual mode.
S. Sport – More dynamic driving.
T Snow – Driving on snowy roads (depending
on engine).
The gearbox then operates in auto-adaptive
mode, without any inter vention on the part
of the driver. It continuously selects the most
suitable gear according to the driving style, the
road profile and the load in the vehicle.
For maximum acceleration without touching
the selector, press the accelerator fully down
(kick-down). The gearbox changes down
automatically or holds the gear selected until
the maximum engine speed is reached.
When braking, the gearbox shifts down
automatically to provide effective engine
braking.
If you release the accelerator sharply, the
gearbox will not shift to a higher gear for safety
reasons.
Manual mode
This mode allows manual sequential gear
changing. F
R
elease the brake pedal and press the
accelerator pedal progressively.
The vehicle moves off immediately.
Driving

86
If the lever is not in position P, an alert
message appears on the screen on
opening the driver's door or approximately
45
seconds after switching off the ignition.
F

R
eposition the lever at position P ; the
message disappears.
When driving on flooded roads or when
crossing a
ford, proceed at walking pace.
When the ignition is on, the lighting
of this warning lamp, accompanied
by an audible signal and a
message
on the screen, indicates a
gearbox
fault.
In this case, the gearbox goes into back-up
mode by staying in 3rd gear. You may feel
a

substantial jolt when changing from P to
R and from N to R . This will not cause any
damage to the gearbox.
Do not exceed 62
mph (100 km/h), local speed
restrictions permitting.
Contact a
PEUGEOT dealer or a qualified
workshop as soon as possible. There is a
risk of damage to the gearbox:
F i f you press the accelerator and brake
pedals at the same time,
F

w
ith a flat battery, if you force the
movement of the lever from position P
to another position.
To reduce fuel consumption during
prolonged stops with the engine running
(e.g. traffic jam), position the gear lever at
N and apply the parking brake.
Gear shift indicator
(Depending on engine.)
System which reduces fuel consumption by
recommending the most appropriate gear.
Operation
Depending on the driving situation and your
vehicle's equipment, the system may advise
you to skip one or more gears. You can
follow this indication without engaging the
intermediate gears.
Gear shift recommendations must not be
considered as compulsory. In fact, the road
layout, the traffic density and safety remain the
deciding factors when choosing the best gear. With an automatic gearbox, the system is
only active in manual operation.
The information appears in the
instrument panel, in the form of an
ascending or descending arrow and
the recommended gear.
The system adapts its gear shift
recommendation according to the driving
conditions (slope, load, etc.) and the
driver's requirements (power, acceleration,
b r a k i n g , e t c .) .
The system never suggests:
-
e
ngaging first gear,
-
enga
ging reverse.
On vehicles fitted with a manual gearbox,
the arrow may be accompanied by the
gear recommended. The system always
recommends to change up if necessary.
Depending on the engine, it may also
recommend to change down if necessary.
The driver therefore remains responsible for
deciding whether or not to follow the indications
issued by the system.
This function cannot be deactivated.
Driving

87
Hill start assist
System that holds your vehicle for around
2 seconds, the time it takes to move your foot
from the brake pedal to the accelerator pedal.
The hill start assist function cannot be
deactivated. However, use of the parking
brake to immobilise the vehicle interrupts
its function. Hill start assist is only available when:
-

y
our foot on the brake pedal fully
immobilises the vehicle,
-

c
ertain slope conditions are met,
-

t
he driver's door is closed.Do not leave the vehicle while it is being
held temporarily by hill start assist.
If you need to leave the vehicle with the
engine running, apply the parking brake
manually. Then ensure that the parking
brake warning lamp is on fixed in the
instrument panel.
Malfunction
If a fault in the system occurs, these warning
l amps come on. Contact a PEUGEOT dealer
or a
qualified workshop to have the system
checked.
Uphill, with the vehicle stationar y, the
vehicle is held for a

shor t time when you
release the brake pedal.
With an automatic gearbox, if you are in
position D . Downhill, with the vehicle stationary and
reverse gear engaged, the vehicle is held
for a

shor t time when you release the brake
pedal.
Stop & Start
The system puts the engine temporarily into
standby – STOP mode – during stops in the
traffic (red lights, traffic jams, etc.). The engine
restarts automatically – START mode – as
soon as you wish to move off again. Restarting
occurs instantaneously, quickly and silently.
Per fect for urban use, the Stop & Start system
reduces fuel consumption and exhaust
emissions as well as the noise level when
stationary.
STOP mode
This indicator lamp comes on in the
instrument panel and the engine
goes into standby.
With BlueHDi Diesel and manual gearbox :
- A s soon as the vehicle stops or the speed is less
than 2
mph (3 km/h) (with 1.5 BlueHDi engine).
-

W
ith gear lever in neutral and clutch pedal
released.
6
Driving

89
Deactivation/Reactivation
In certain circumstances, such as the need
to maintain the temperature in the passenger
compartment, it may be useful to deactivate the
Stop & Start system.
The system can be deactivated at any time,
once the ignition is switched on.
If the engine is in STOP mode, it then restarts.
The Stop & Start system is reactivated
automatically every time the ignition is switched
on.Opening the bonnet Driving on flooded roads
Before driving through a
flooded road, it is
strongly recommended that you deactivate
the Stop & Start system.
For more information on Driving advice ,
particularly on flooded roads, refer to the
corresponding section.
Malfunction
The Stop & Start system requires a 12 V
b attery of specific technology and
specification.
All work on this type of battery must be
carried out only by a
PEUGEOT dealer or
a


qualified workshop.
For more information on the 12
V batter y,
refer to the corresponding section.
F

T

o deactivate or reactivate the system,
press this button.
The indicator lamp is lit when the system is
deactivated.
Before doing anything under the bonnet,
deactivate the Stop & Start system to avoid
the risk of injury related to an automatic
change to START mode.
Under-inflation detection
This system automatically monitors the tyre
pressure while driving.
The system monitors the pressure in all four
tyres, once the vehicle is moving.
It compares the information given by the
wheel speed sensors with reference values,
which must be reinitialised after ever y tyre
pressure adjustment or wheel change .
The system triggers an alert as soon as it
detects a
drop in the pressure of one or more
tyres.
In the event of a

fault with the system, the ECO
OFF switch warning lamp flashes, then comes
on fixed.
Have it checked by a

PEUGEOT dealer or
a


qualified workshop.
If a

fault occurs in STOP mode, the vehicle
may stall. All of the instrument panel warning
lamps come on. It is then necessary to switch
the ignition off and to restart the engine using
t h e key.
6
Driving

90
The tyre under-inflation detection system
does not replace the need for vigilance on
the part of the driver.
This system still requires you to check
the tyre inflation pressures (including
the spare wheel) every month as well as
before a

long journey.
Driving with under-inflated tyres impairs
handling, extends braking distances and
causes early tyre wear, particularly in
adverse conditions (heavy loads, high
speeds, long journeys).
Driving with under-inflated tyres
increases fuel consumption.
The tyre pressure specifications for your
vehicle can be found on the tyre pressure
label.
For more information on the
Identification markings , refer to the
corresponding section. Tyre pressures should be checked when
the tyres are "cold" (vehicle stopped for
1
hour or after a journey of less than
6
miles (10 km) at moderate speeds).
Other wise (when hot), add 0.3
bar to the
pressures shown on the label.
Under-inflation alert
This warning is indicated by fixed
illumination of this warning lamp, an
audible signal and, depending on
the equipment installed, a message
displayed on the screen.
F

R

educe speed immediately, avoid excessive
steering movements and sudden braking.
F

S

top the vehicle as soon as it is safe to do
so.
The loss of pressure detected does not
always cause visible bulging of the tyre.
Do not satisfy yourself with just a
visual
check. or
F

i
f it is not possible to carry out this check
immediately, drive carefully at reduced
speed.
The alert is kept active until the system is
reinitialised.
The under-inflation alert can only be relied
on if the reinitialisation of the system has
been done with the pressures in the four
tyres correctly adjusted.
Reinitialisation
The system must be reinitialised after any
adjustment to the pressure of one or more
tyres, and after changing one or more wheels.
Before reinitialising the system, ensure
that the pressures of the four tyres
are correct for the conditions of use
of the vehicle and conform to the
recommendations on the tyre pressure
label.
The under-inflation alert can only be relied
on if the reinitialisation of the system has
been done with the pressures in the four
tyres correctly adjusted.
The under-inflation detection system
does not give a
warning if a pressure is
incorrect at the time of reinitialisation.
F

I

n the event of a

puncture, use the
temporary puncture repair kit or the spare
wheel (depending on equipment),
or
F

i

f you have a

compressor, such as the one
in the temporary puncture repair kit, check
the pressures of the four tyres when cold,
Driving

91
Without touch screen
F With the ignition on and the vehicle stationary, press this button for about
3
seconds then release it, an audible signal
confirms the reinitialisation.
With touch screen
The reinitialisation of the system is done with
the ignition on and the vehicle stationary.
The reinitialisation of the system is
configured in the Driving/Vehicle
menu.
The new pressure parameters saved are
treated as reference values by the system.
Snow chains
The system does not have to be
reinitialised after fitting or removing snow
chains.
Malfunction
The flashing and then fixed illumination of the
under-inflation warning lamp, accompanied by
the illumination of the Ser vice warning lamp,
indicates a fault with the system.
In this case, under-inflation monitoring of the
tyres is no longer assured.
Have the system checked by a
PEUGEOT
dealer or a
qualified workshop.
After any inter vention on the system,
the pressures of the four tyres must be
checked and the system reinitialised.
Speed limiter "LIMIT"
The system prevents the vehicle from
exceeding the speed setting programmed by
the driver.
Steering mounted controls
1. Speed limiter mode selection/off.
2. Increases the set value.
3. Decreases the set value.
4. Speed limiter on/pause.
The speed setting is selected with the engine
running, stationary or when driving. The
minimum speed setting possible is 19
mph
(30


km/h).
The vehicle responds to the accelerator until
resistance is felt in the pedal, which signifies
that the vehicle has reached the limiter speed
setting.
However, pressing the pedal beyond this point
of resistance to the floor permits exceeding
of the programmed speed. To resume use
of the limiter, simply reduce the pressure on
the accelerator pedal gradually and return to
a


speed below that programmed.
Setting and operation of the system can be
done stationar y with the engine running or
when driving.
6
Driving

99
Deactivation/activation of the
front and rear parking sensors
Without touch screen
F To deactivate or activate the system, press this button.
The indicator lamp is illuminated when the
system is deactivated.
The deactivation or activation of
the function is done in the Driving/
Vehicle menu.
The function will be deactivated
automatically if a
trailer is being towed
or a
bicycle carrier is fitted (vehicle fitted
with a
towing device or bicycle carrier
recommended by PEUGEOT).
Operating limits
- Certain obstacles located in the sensors' blind spots may not be detected or no
longer be detected during the manoeuvre.
-

S
ounds such as those emitted by noisy
vehicles and machinery (e.g. lorries,
pneumatic drills, etc.) may inter fere with the
vehicle's sensors.
-

C
ertain materials (fabrics) absorb sound
waves: pedestrians may not be detected.
-

A
ccumulated snow or dead leaves on the
road sur face can inter fere with the vehicle's
sensors.
-

A f
ront or rear impact to the vehicle can
distort the settings of the sensors, which is
not always detected by the system: distance
measurements may be incorrect.
-

T
he tilting of the vehicle if the boot is
very loaded can affect the distance
measurements.
-

T
he sensors may be affected by poor
weather conditions (heavy rain, thick fog,
snowfall, etc.).
Maintenance
recommendations
In bad or wintry weather, ensure that the
sensors are not covered with mud, ice or
snow. When reverse gear is engaged, an
audible signal (long beep) indicates that
the sensors may be dirty.
High-pressure jet wash
When washing your vehicle, keep the
lance at least 12
inches (30 cm) away from
the sensors.
Operating fault
If a fault occurs when shifting
t o reverse, this warning lamp
comes on in the instrument panel,
accompanied by a
message and an
audible signal (short beep).
Contact a
PEUGEOT dealer or a qualified
workshop to have the system checked.
With touch screen
6
Driving

101
For entry into a parallel parking space, the
system does not detect spaces which are
clearly much smaller or larger than the
size of the vehicle.
The "Parking sensors" function activates
automatically during the manoeuvres, so it
is possible that a


warning lamp illuminates
on the screen, accompanied by an audible
signal, without affecting the parking.
Changing tyre sizes (out-size tyres, winter
tyres, etc.) can inter fere with the correct
operation of the parking sensors system.
When the Park Assist is active, it prevents
Stop & Start going into STOP mode.
In STOP mode, activating Park Assist
restarts the engine.
Entering a parallel parking
space
F Once you have detected an available space,
limit the speed of the vehicle to 12 mph
(20


km/h).
The system provides assistance in entering and
exiting a


parking space when parallel parking.
F
P
osition your vehicle before this space.
To activate the Park Assist system:
F

P
ress this control.
The indicator lamp in the control remains off.
A message is displayed in the screen. F

S
elect the enter parking space manoeuvre.
The indicator lamp in the control comes on.
F

O
perate the direction indicator on the
parking side.
F

M
ove for wards alongside the parking
space at a
speed below 12 mph (20 km/h)
to measure it, keeping at a
distance of
between 0.5
and 1.5 metres from the row of
parked vehicles.
6
Driving