warning Peugeot 208 2019 Owner's Guide

32
Reinitialising the remote
control
Following replacement of the battery or in
the event of a remote control fault, it may be
necessary to reinitialise the remote control.
F

S
witch off the ignition.
F

T
urn the key to position 2

(Ignition on).
F

P
ress the closed padlock button for a few
seconds.
F

S
witch off the ignition and remove the key
from the switch.
The remote control is now fully operational
again.
Boot
Opening
F After unlocking the boot or the vehicle using the remote control or the key, press
the opening control, then raise the tailgate.
Closing
F Lower the tailgate using the interior grab handle.
F

I
f necessary, press down on the tailgate to
fully close it.
If the tailgate is not fully closed:
-

w
ith the engine running ,
this warning lamp comes on,
accompanied by the display of an
alert message for a
few seconds,
-

w
hen driving (speed above 6
mph
(10
km/h)), this warning lamp comes on,
associated with an audible signal and
the display of an alert message for a
few
seconds. In the event of a
fault or difficulties felt in
manoeuvring the tailgate when opening
or closing it, have it quickly checked
by a PEUGEOT dealer or a qualified
workshop to stop this issue getting worse
and so as to not cause the tailgate to drop,
and serious injuries.
Backup control
System for mechanical unlocking of the boot in
the event of a central locking malfunction.
Unlocking
F Fold the rear seats to gain access to the lock from inside the boot.
F

I
nsert a small screwdriver into hole A of the
lock to unlock the boot.
F

M
ove the latch to the left.
Access

53
Switching on
F Turn the ring to the "AUTO" position.
Activation of the function is accompanied by
a
message on the screen.
Switching off
F Turn the ring to another position. Deactivation of the function is accompanied
by a
message in the screen.
In fog or snow, the sunshine sensor may
detect sufficient light. In this case, the
lighting will not come on automatically.
Do not cover the sunshine sensor, linked
with the rain sensor and located in the
centre of the windscreen behind the rear
view mirror; the associated functions
would no longer be controlled.
Automatic guide-me-home
lighting
When associated with automatic illumination of
headlamps, the guide-me-home lighting offers
the following additional options:
-

s
election of the lighting duration of 15, 30 or
60


seconds,
-

a
utomatic activation of guide-me-home
lighting when the automatic illumination of
headlamps is in operation.
The guide-me-home lighting can be
configured in the Driving/Vehicle
menu.
In the event of a
fault with the
sunshine sensor, the lighting comes
on, this warning lamp is displayed
in the instrument panel and/or
a
message appears on the screen,
accompanied by an audible signal.
Contact a
PEUGEOT dealer or
a


qualified workshop.
Manual guide-me-home
lighting
Temporarily keeping the dipped beam
headlamps on after the vehicle's ignition has
been switched off makes the driver's exit easier
when the light is poor.
Switching on
F With the ignition off, "flash" the headlamps using the lighting control stalk.
F

A f
urther "headlamp flash" switches the
function off.
Manual guide-me-home lighting is
also available from the remote control
lighting button.
Switching off
Manual guide-me-home lighting goes off
automatically at the end of a given period of
time.
4
Lighting and visibility

58
General safety
recommendations
Labels are affixed in different locations on
your vehicle. They include safety warnings
and vehicle identification information. Do
not remove them: they are an integral part
of your vehicle.
For any work on your vehicle, use
a qualified workshop that has the technical
information, skills and equipment required,
all of which a
PEUGEOT dealer is able to
provide.
Depending on country regulations, some
safety equipment may be compulsory:
high visibility safety vests, warning
triangles, breathalysers, spare bulbs,
spare fuses, fire extinguisher, first aid kit,
mud flaps at the rear of the vehicle, etc. We draw your attention to the following
points:
-

T
he fitting of electrical equipment
or accessories not approved by
PEUGEOT may cause excessive
current consumption and faults and
failures with the electrical system of
your vehicle. Contact a
PEUGEOT
dealer for information on the range of
recommended accessories.
-

A
s a safety measure, access to
the diagnostic socket, used for the
vehicle's electronic systems, is
reser ved strictly for PEUGEOT dealers
or qualified workshop, equipped
with the special tools required (risk
of malfunctions of the vehicle's
electronic systems that could cause
breakdowns or serious accidents).
The manufacturer cannot be held
responsible if this advice is not
followed.
-

A
ny modification or adaptation not
intended or authorised by PEUGEOT
or carried out without meeting the
technical requirements defined by
the manufacturer will result in the
suspension of the legal and contractual
warranties. Installation of accessory radio
communication transmitters
Before installing a


radio communication
transmitter, you must contact a PEUGEOT
dealer for the specifications of compatible
transmitters (frequency, maximum power,
aerial position, specific installation
requirements), in line with the Vehicle
Electromagnetic Compatibility Directive
(2004/104/EC).
Hazard warning lamps
F When you press this red button, all four direction indicators flash.
They can operate with the ignition off.
Automatic operation of
hazard warning lamps
When braking in an emergency, depending on
the deceleration, the hazard warning lamps
come on automatically.
Safety

61
Anti-lock braking system
(ABS) and electronic brake
force distribution (EBFD)
The fixed illumination of this warning
lamp indicates that there is a fault
with the ABS.
The vehicle retains conventional braking. Drive
carefully at moderate speed. If these warning lamps come on,
accompanied by an audible signal
and a
message, this indicates a fault
with the electronic brake force
distribution (EBFD) system.
When changing wheels (tyres and rims),
ensure that these are approved for your
vehicle.
Normal operation of the ABS may make
itself felt by slight vibration of the brake
pedal. If you need to brake in an emergency,
press the brake pedal ver y firmly and
keep the pressure applied.
You must stop as soon as it is safe to do so.
In both cases, have the system checked by
a

PEUGEOT dealer or a qualified workshop as
soon as possible.Anti-slip regulation (ASR)/
Dynamic stability control
(DSC)
Operation
These systems are activated automatically
every time the vehicle is started.
They come into operation in the event of
a
problem with grip or trajectory. This is indicated by flashing of this
warning lamp in the instrument panel.
Deactivation
In exceptional conditions (starting a vehicle
w hich is bogged down, stuck in snow, on soft
ground, etc.), it may be advisable to deactivate
these systems, so that the wheels can turn
freely and regain grip.
Reactivate these systems as soon as the level
of grip permits.
Deactivation of ASR and DSC using the button
F Press this button.
The orange indicator lamp in the button comes
on.
The ASR and DSC systems will no longer have
an effect on engine operation or the brakes in
the event of an involuntary change of trajectory.
Deactivation of ASR using the touch screen
The deactivation is configured in the
Driving/Vehicle menu.
It is confirmed by the display of a
message.
Reactivation
These systems are reactivated automatically
each time the ignition is switched back on or
above 31 mph (50 km/h).
Below 31
mph (50 km/h), you can reactivate
them manually.
5
Safety

62
Seat belts
At the front
The front seat belts are fitted with
a pretensioning and force limiting system.
This system improves safety in the front
seats in the event of a
front or side impact.
Depending on the severity of the impact, the
pretensioning system instantly tightens the seat
belts against the body of the occupants.
The pretensioning seat belts are active when
the ignition is on.
The force limiter reduces the pressure of
the seat belt on the passenger's chest, thus
improving their protection.
Reactivation of ASR and DSC using the
button
F

P

ress the button again to reactivate
manually.
The indicator lamp in the button goes off.
Reactivation of ASR using the touch screen
The reactivation is configured in the
Driving/Vehicle menu.
It is confirmed by the display of a

message.
Malfunction
Illumination of this warning lamp,
accompanied by the display of
a
message and an audible signal,
indicates a
fault with the system.
Contact a
PEUGEOT dealer or a qualified
workshop to have the systems checked. ASR/DSC
These systems offer increased safety
in normal driving, but they should not
encourage the driver to take extra risks or
drive at high speed.
It is in conditions of reduced grip (rain,
snow, ice) that the risk of loss of grip
increases. It is therefore important for your
safety to keep these systems activated in
all conditions, and particularly in difficult
conditions.
The correct operation of these
systems depends on obser vation of
the manufacturer's recommendations
regarding both the wheels (tyres and
rims), braking and electronic components
and the assembly and repair procedures
used by PEUGEOT dealers.
The use of snow tyres is recommended,
in order to be able to benefit from the
efficiency of these systems in winter
conditions.
In this case, it is essential to equip the
four wheels with tyres approved for your
vehicle.
Safety

63
Fastening
F Pull the strap then insert the tongue in the buckle.
F

C
heck that the seat belt is fastened
correctly by pulling the strap.
Unfastening
F Press the red button on the buckle.
F G uide the seat belt as it reels in.
Height adjustment
F To raise the attachment point, slide the control A upwards.
Warning lamp
Not fastened/unfastened.
When the ignition is switched on,
this warning lamp comes on in the
instrument panel.
It remains on for a certain time if the front
p assenger has not fastened their seat belt. Once
this period has elapsed, the warning lamp goes off
if the driver's seat belt is fastened.
From approximately 12
mph (20 km/h) this warning
lamp flashes for 2


minutes accompanied by an
audible signal of increasing volume if the driver
and/or the front passenger have not fastened their
seat belt. Once these 2
minutes have elapsed, this
warning lamp remains on until the driver and/or
the front passenger fastens their seat belt.
At the rear
Fastening
F Pull the strap then insert the tongue in the buckle.
F

C
heck that the seat belt is fastened
correctly by pulling the strap.
Unfastening
F Press the red button on the buckle.
F G uide the seat belt as it reels in.
F

O
n the outer seat belts, raise the bar to the
top of the backrest to prevent the tongue
from knocking against the side trim.
F

T

o lower the attachment point, squeeze the
control A and slide it downwards. The rear seats are each fitted with a
three-point
seat belt equipped, for the outer seats, with
a

force limiter.
Warning lamp
Unfastened.
From approximately 12
mph
(20
km/h) and for 2 minutes, this
warning lamp flashes, accompanied
by an audible signal of increasing
volume, when one or more rear
passengers unfasten their seat belt.
Once these two minutes have elapsed, this
warning lamp remains on until one or more rear
passengers fasten their seat belt.
5
Safety

64
Advice
The driver must ensure that passengers
use the seat belts correctly and that they
are all fastened before setting off.
Wherever you are seated in the vehicle,
always fasten your seat belt, even for
short journeys.
Do not interchange the seat belt buckles
as they will not fulfil their role fully.
The seat belts are fitted with an inertia
reel permitting automatic adjustment of
the length of the strap to your size. The
seat belt is stowed automatically when not
in use.
The inertia reels have an automatic
locking device at the time of a collision,
during sudden braking or if the vehicle
turns over. You can release the device by
pulling the strap firmly and then releasing
it so that it reels in slightly.
Before and after use, ensure that the seat
belt is reeled in correctly.
After folding or moving a
seat or rear
bench seat, ensure that the seat belt is
positioned and reeled in correctly. Installation
The lower part of the strap must be
positioned as low as possible on the
pelvis.
The upper part must be positioned in the
hollow of the shoulder.
In order to be effective, a seat belt must:
-

b
e tightened as close to the body as
possible,
-

b
e pulled in front of you with a smooth
movement, checking that it does not
twist,
-

b
e used to restrain only one person,
-

n
ot show any signs of cuts or fraying,
-

n
ot be converted or modified to avoid
affecting its performance.
Recommendations for children
Use a
suitable child seat if the passenger
is less than 12
years old or shorter than
one and a
half metres.
Never use the same seat belt to secure
more than one child.
Never allow a
child to travel on your lap.
For more information on Child seats , refer
to the corresponding section. Maintenance
In accordance with current safety
regulations, for all repairs on your
vehicle's seat belts, go to a
qualified
workshop with the skills and equipment
needed, which a
PEUGEOT dealer is able
to provide.
Have your seat belts checked regularly
by a
PEUGEOT dealer or a qualified
workshop, particularly if the straps show
signs of damage.
Clean the seat belt straps with soapy
water or a
textile cleaning product, sold by
PEUGEOT dealers.
In the event of an impact
Depending on the nature and
seriousness of the impact , the
pyrotechnic pretensioner may be deployed
before and independently of the airbags.
Deployment of the pretensioners is
accompanied by a
slight discharge of
harmless smoke and a
noise, due to the
activation of the pyrotechnic cartridge
incorporated in the system.
In all cases, the airbag warning lamp
comes on.
Following an impact, have the seat
belts system checked and, if necessary,
replaced, by a
PEUGEOT dealer or
a


qualified workshop.
Safety

66
Lateral airbags
System which protects the driver and front
passenger in the event of a serious side impact
in order to limit the risk of injury to the chest,
between the hip and the shoulder.
Each lateral airbag is fitted in the seat backrest
frame, door side.
Deployment
It is deployed on one side in the event of
a serious side impact applied to all or part
of the side impact zone B , perpendicular
to the longitudinal centreline of the vehicle
on a
horizontal plane and directed from the
outside towards the inside of the vehicle.
The lateral airbag inflates between the hip and
shoulder of the front occupant of the vehicle
and the corresponding door trim panel.
Curtain airbags
System contributing towards greater protection
for the driver and passengers (with the
exception of the rear centre passenger) in the
event of a
serious side impact in order to limit
the risk of injury to the side of the head.
Each curtain airbag is built into the pillars and
the upper passenger compartment area.
Deployment
The curtain airbag is deployed at the same
time as the corresponding lateral airbag in the
event of a
serious side impact applied to all or
part of the side impact zone B , perpendicular
to the longitudinal centreline of the vehicle
on a
horizontal plane and directed from the
outside towards the inside of the vehicle.
The curtain airbag inflates between the front or
rear occupant of the vehicle and the windows.
Operating fault
If this warning lamp in the instrument
panel comes on, you must contact
a
PEUGEOT dealer or a qualified
workshop to have the system
checked. The airbags might no
longer deploy in a


crash. In the event of a
minor impact or bump on
the side of the vehicle or if the vehicle rolls
over, the airbag may not be deployed.
In the event of a rear or front collision, the
airbag is not deployed.
Safety

69
The warning label present on both sides of the
passenger sun visor repeats this advice.
In line with current legislation, you will find this
warning in all the required languages in the
following tables.
Passenger airbag OFF
Deactivating the front passenger
airbag
F With the ignition off, insert the key in the
passenger airbag deactivation switch.
F

T
urn it to the OFF position.
F

R
emove the key while keeping the switch in
this position.
When the ignition is switched on,
this warning lamp comes on in the
instrument panel. It stays on while
the airbag is deactivated. To ensure the safety of your child, the front
passenger airbag must be deactivated
when you install a
"rear ward facing" child
seat on the front passenger seat.
Otherwise, the child would risk being
seriously injured or killed if the airbag
were deployed.
Reactivating the front passenger
airbag
When you remove the "rear ward facing" child
seat, with the ignition off , turn the switch to
the ON position to reactivate the airbag and so
assure the safety of your front passenger in the
event of an impact.
When the ignition is switched on,
this warning lamp comes on in the
instrument panel, for approximately
one minute, to signal that the front
airbag is activated.
5
Safety

81
Side wind
F Take into account the increased sensitivity to wind.
Cooling
Towing a trailer on a slope increases the
t emperature of the coolant.
As the fan is electrically controlled, its cooling
capacity is not dependent on the engine speed.
F

T
o lower the engine speed, reduce your
speed.
The maximum towable load on an incline
depends on the gradient and the exterior
temperature.
In all cases, keep a
check on the coolant
temperature.
F

I
f this warning lamp and the
STOP warning lamp come on,
stop the vehicle and switch off
the engine as soon as possible.
New vehicle
Do not tow a
trailer before having driven at
least 620
miles (1,000 kilometres).
Braking
Towing a trailer increases the braking distance.
T o avoid overheating of the brakes, the use of
engine braking is recommended.
Ty r e s
F Check the tyre pressures of the towing vehicle and of the trailer, observing the
recommended pressures.
Lighting
F Check the electrical lighting and signalling on the trailer and the headlamp beam height
of your vehicle.
For more information on Headlamp
beam height adjustment , refer to the
corresponding section.
Certain driving or manoeuvring aid
functions are automatically disabled if an
approved towing device is used.
Starting – Switching off
the engine
Ignition switch
1. Stop position.
2. Ignition on position.
3. Start position.
Avoid attaching heavy objects to the key
or the remote control, which would weigh
down on its blade in the ignition switch
and could cause a


malfunction.
Starting
With a manual gearbox, p lace the gear
selector in neutral then fully depress the clutch
pedal.
With an automatic gearbox , place the gear
selector at P or N then fully depress the brake
pedal.
6
Driving