battery Peugeot 306 Break 2002 Owner's Manual

MAINTENANCE OF YOUR 30623
PEUGEOT SERVICING LEVELS A AND C
First Level
Operations Description of operations
serviceACIntermediate visit
DRAIN AND REFILL- Engine oil.- Bleed fuel filter (diesel).- Oil filter.- Fuel filter (Petrol).REPLACEMENT- Fuel filter element (Diesel).- Air filter element.- Spark plugs (Petrol).- Engine oil (check + top up).- Manual gearbox oil (check + top up).- Battery (check + top up) if cap is removable.LEVEL- Front/rear windscreen wash (check + top up).- Coolant (check + top up).- Brake fluid (check + top up).- Power steering fluid (check + top up according to specification).- Operation of lights and indicators.- Condition of glass, headlamp and light lenses and mirrors.- Horn.- Windscreen washer jets.- Condition of wiper blades.- Condition and tension of ancillary drive belts.- Handbrake.- Condition of hydraulic circuits (hoses and covers), check for leaks.CHECK- Condition of rubber boots and gaiters.- Brake pad wear. - Play in hubs, rods, ball joints, flexible mountings.- Shock absorbers for leaks.- Rear drum brake lining wear.- Condition and pressure of tyres (including spare wheel).- Emission control check according to current legislation (Petrol).- Smoke opacity (Diesel).- Pollen filter check (according to specification). - Visual check of the whole vehicle by a PEUGEOT dealer.
: All driving conditions : Arduous conditions

92
YOUR 306 IN DETAIL
1Low coolant level*.
2 Headlamp main beam.
3 Pre-heat (Diesel).
4 Headlamp dipped beam.
5 Water in fuel filter warning light* (Diesel).
6 Speedometer.
7 Left indicator.
8 Low oil pressure warning light.
9 Handbrake low brake fluid level andelectronic brake force distribution.
10 Battery charge. 11
Right indicator.
12 Rev counter.
13 Front fog lamps*.
1 4 Rear fog lamp.
15 ABS: anti-lock braking system*.
16 Fuel gauge.
17 Low fuel level.
18 STOP warning.
19 Seat belt not fastened warning light*.
20 Disarming of passenger airbag**. 21
Side airbags warning light*.
22 Front* and side** airbag warninglight and disarming passengerairbag*.
23 Autodiagnostics*.
24 Trip recorder and service indicator.
25 Trip recorder zero reset and clocksetting.
26 Coolant temperature gauge.
* According to specification or country.
** According to model.
56 78 910 11 12 13 14 15
4 321
26 25 24 23 22 21 20 19 18 17 16
INSTRUMENT PANEL

93
YOUR 306 IN DETAIL
13 14
1Low coolant level.
2 Headlamp main beam.
3 Headlamp dipped beam.
4 Speedometer.
5 Left indicator.
6 Low oil pressure warning light.
7 Handbrake low brake fluid level and electronic brake force distribution.
8 Battery charge.
9 Right indicator.
10 Rev counter.
11 Front fog lamps. 12
Brake pad wear warning light*.
13 Rear fog lamp.
14 ABS: anti-lock braking system*.
15 Fuel gauge.
16 Low fuel level.
17 Oil level and temperature gauge.
18 STOP warning.
19 Seat belt not fastened warninglight*.
20 Disarming of passenger airbag**.
21 Side airbags warning light*. 22
Front* and side** airbag warninglight and disarming passengerairbag*.
23 Autodiagnostics*.
24 Trip recorder and service indicator.
25 Trip recorder zero reset and clocksetting.
26 Coolant temperature gauge.
* According to specification or country.
** According to model.
12 3 4 56789 1 0 11 1 2
26 25 24 23 22 21 20 19 18 17 16 15
13 14
INSTRUMENT PANEL

94
YOUR 306 IN DETAIL
1Low coolant level*.
2 Headlampt main beam.
3 Pre-heat (Diesel).
4 Headlamp dipped beam.
5 Water in fuel filter warning light* (Diesel).
6 Speedometer.
7 Left indicator.
8 Low oil pressure warning light.
9 Gear indicator (automatic gearbox).
10 Handbrake low brake fluid level andelectronic brake force distribution. 11
Battery charge.
12 Right indicator.
13 Rev counter.
14 Front fog lamps*.
15 Rear fog lamp.
16 ABS: anti-lock braking system*.
17 Fuel gauge.
18 Low fuel level.
19 Oil level.
20 STOP warning.
21 Seat belt not fastened warninglight*. 22
Disarming of passenger airbag**.
23 Side airbags warning light**.
24 Front* and side** airbag warninglight and disarming passengerairbag*.
25 Autodiagnostics*.
26 Trip recorder and service indicator.
27 Trip recorder zero reset and clocksetting.
28 Coolant temperature gauge.
* According to specification or country.
** According to model.
56 78910 11 12 13 14 15 16
4 321
28 27 26 25 24 23 22 21 20 19 18 17
INSTRUMENT PANEL

95
YOUR 306 IN DETAIL
A warning light which remains per- manently lit indicates that the unit con-
cerned is not operating correctly. Donot ignore this warning: contact a
PEUGEOT dealer as soon as possible.
Coolant temperature gauge
- needle in zone A, the temperature
is correct.
- needle in zone B, the temperature
is too high.
The STOP warning light comes on.
You must stop.
Contact a PEUGEOT dealer.
* According to specification.
Handbrake, low brake fluid level and electronicbrake force distributionwarning light
Indicates either:
Ð that the handbrake is on or has not been released correctly,
Ð an excessive drop in the brake fluid level (if the light remains lit even with the handbrake released),
Ð a malfunction of the braking system, if lit at the same time as the ABSwarning light.
Stop immediately.
Contact a PEUGEOT dealer.
STOP warning light
(Together with the oil pressure warning light).
You must stop.
Contact a PEUGEOT dealer. Oil pressure warning light
Together with the STOP warning light.
You must stop. Indicates either:
- oil pressure is too low,
- a lack of oil in the lubricating circuit.
Top up the oil level if necessary.
Contact a PEUGEOT dealer.
Battery charge warning light Indicates either: - faulty operation of the
battery charging circuit,
- loose battery or starter terminals,
- a broken or loose alternator drive belt
- an alternator fault,
Contact a PEUGEOT dealer. Low coolant level warning light*
You must stop.
Wait until the engine cools
before topping up.The cooling circuit is pressurised.When opening to top up, turn the cap to the first notch to let the pressuredrop.
Contact a PEUGEOT dealer.
Engine autodiagnostic warning light* This comes on each time the ignition is switched on. If itcomes on when driving, this
indicates faulty operation of the injec-tion, ignition or emission controlsystem. There is a risk of damage to the cat- alytic converter if your vehicle is fitted with one.
Contact a PEUGEOT dealer.
Low fuel warning light Indicates that there are approximately 1.3 gallons(6 litres) of fuel remainingin the fuel tank.
(The capacity of the tank is approxi-mately 60 litres).
A
B
INSTRUMENTS AND CONTROLS

YOUR 306 IN DETAIL
58
GENERAL FUNCTIONS On / off
With the ignition key in the ACCESSORIES or IGNITION position, press the "ON/VOL"button to switch the set
on or off. ANTI-THEFT SYSTEM
The first time you use the set following disconnection of the set or the battery, you must enter the confidential code which was given to you on handover of your vehicle. Entering the code Switch the set on. The display shows "CODE"then the set changes over to code request mode and " - - - -" is displayed.
Enter your four-digitcode number using buttons " 1" to " 6".
For example: if your code is 5345 press buttons " 5", " 3", " 4" and " 5" in turn.
When the fourth number has been entered correctly, the radio starts automatically.
Error in entering the code
If an error is made when entering one of the first three digits, do not continue the operation and switch off the radio to prevent blocking it. Each incorrect code entry will result in the set being blocked for a period of from 5 seconds to 30 minutes, after
the 7th incorrect entry.
To unblock the set, leave it switched on during the waiting period. When " - - - -" is displayed, you can enter the
code again.
If the set is switched off during the waiting period, this waiting period will restart when the set is switched on again.After 14 incorrectly input codes, the radio will be permanently locked and the display will read ÒENDÓ.
ADJUSTING THE SOUND Adjusting the volume
Turn the "M"button to increase or decrease the volume of the set.
In the event of the radio overheating, the volume reduces. If an attempt is made to increase the volume the message " TOO HOT ÕÕ appears on the display.
Note If you have a telephone fitted with a Ò muteÓ signal output connected to the set, the set will automatically change
to Ò mute Ó when the telephone is used.

68
YOUR 306 IN DETAIL
GENERAL FUNCTIONS On / off
With the ignition key in the ACCESSORIES or IGNITION position, press the "M"button to switch the set on or off.
The set can operate for 30 minutes without switching the ignition on. ANTI-THEFT SYSTEM
The first time you use the set following disconnection of the set or the battery, you must enter the confidential code which was given to you on handover of your vehicle. Entering the code Switch the set on. The display shows " CODE IN" then the set changes over to code request mode and " - - - -" is displayed.
Enter your four-digitcode number using buttons " 1" to " 6".
For example: if your code is 5345 press buttons " 5", " 3", " 4" and " 5" in turn.
When the fourth number has been entered correctly, the radio starts automatically.
Error in entering the code
If an error is made when entering one of the first three digits, do not continue the operation and switch off the radio to prevent blocking it. Each incorrect code entry will result in the set being blocked for a period of from 5 seconds to 30 minutes, after
the 7th incorrect entry.
To unblock the set, leave it switched on during the waiting period. When " - - - -" is displayed, you can enter the
code again.
If the set is switched off during the waiting period, this waiting period will restart when the set is switched on again.After 14 incorrectly input codes, the radio will be permanently locked and will display ÒENDÓ.
ADJUSTING THE SOUND Adjusting the volume
Turn the "ON/VOL" button Mto increase or decrease the volume of the set.
In the event of the radio overheating, the volume level decreases. Note If you have a telephone fitted with a Ò muteÓ signal output connected to the set, the set will automatically change
to Ò mute Ó when the telephone is used.

THE REMOTE CONTROL
A single press on button Alocks the
doors and boot or tailgate, this is dis- played by the direction indicatorsstaying on for about 2 seconds.
A single press on button Bunlocks
the vehicle, this is displayed by the
direction indicators flashing rapidly.
YOUR 306 IN DETAIL
78
KEYS
Without central locking The key individually Iocks and unlocks the doors and boot or tailgate.
With central locking
Turning the key in the driverÕs door lock will lock or unlock the doors andboot or tailgate. If either of the frontdoors is not closed, the central lockingwill not work.
CHANGING THE REMOTE
CONTROL BATTERIES
To gain access to the battery, unclip the key casing with a coin where youcan see the ring (CR1620/3 volt battery). If the remote control does not work after the battery has been changed,re-programme the remote control. PROGRAMMING THE REMOTE CONTROL Manual synchronisation
- Switch off the ignition,
- Switch on the ignition,
- Immediately after switching on the
ignition press button A.
The remote control is now working again. Automatic synchronisation
- Switch on the ignition (position M),
- Switch off the ignition and, during the next four minutes, lock the vehicle using the remote control(button A).
The remote control is now workingagain.
Note: do not repeatedly press the
button of your remote control out of
range of your vehicle. You riskcausing it not to work and the remotecontrol would have to be repro-grammed.
A
B

SPECIAL FEATURES
124
DEADLOCKING* Deadlocking is an additional security device which means that the interior and exterior door controls cannot open the doors, when deadlocked. Deadlocking can be carried out in two ways:
- With the remote control.
- With the ignition key.
To operate deadlocking After locking the doors you have five seconds in which to operate the dead- locking. If using the remote control:
- press button
1once to lock your vehicle, the direction indicators stay on for
2 seconds.
- press button 1for a second time within the five seconds to deadlock your vehi-
cle, the direction indicators flash once.
- press button 2to unlock your vehicle, the direction indicators flash several times.
If using the ignition key, keep the key in the lock of one of the front doors, with the key turned towards the rear of the vehicle (turn the key towards the front to unlock).
To unlock the doors and boot or tailgate Place the ignition key in the lock of one of the front doors and turn ittowards the front of the vehicle.
Alternatively, press button 2on the
remote control.
* According to specification. Important After deadlocking, anybody inside
the car, and without the remotecontrol, will not be able to get out
by themselves. The doors canonly be unlocked by using theremote control, or the ignition keyin the door lock. If the battery is disconnected deadlocking remains activated. Itis still possible to open one of the
front doors using the ignition key,but the key will only open that par-
ticular door.
1
2

SPECIAL FEATURES
126
ALARM SYSTEM* Setting and disarming the alarm Switching off the siren The alarm completes the security equipment of your vehicle. It com-prises two types of protection: -exterior protection: when this is
set, the alarm sounds if a door,
the bonnet, the boot or the tail- gate are opened.
- interior sensor protection: when
it is set, the alarm sounds if thesensors detect a variation in the
air movement inside the vehicle(breaking of a window) or amovement inside the vehicle.
It is also equipped with an anti-
tamper function. If an attempt is made to neutralise the leads to the siren, the centralcontrol or the battery:
- the alarm is triggered,- the siren sounds, the headlights come on*. To set the alarm (exterior and interior protection) The ignition must be switched off.
You must be outside the vehiclePress the locking button of the remote control key (if your vehiclehas deadlocking, you then need topress this button again). The doors will lock.The direction indicators come on continuously for two seconds. The red lamp on the switch flashes once a second. Five seconds afterwards : the exteri- or protection is set. Fifty seconds afterwards : the interi- or protection is set. Note :
when the alarm is triggered,
the siren sounds for thirty seconds. It then stops, but the alarm remains set.
Warning
If, on setting the alarm, a door, the boot, tailgate or the bonnet are notproperly closed, the siren will be trig-
gered briefly. If the vehicle is proper-ly closed within forty five secondsafter this, the alarm is set, the direc-tion indicators come on continuouslyfor two seconds. In all cases the alarm is set forty five seconds afterwards. To disarm the alarm (exteriorand interior protection) Press the unlocking button on the remote control. The doors unlock.The direction indicators flash for two seconds. The red lamp on the switch goes out.Note :
if the lamp continues to flash
after disarming the alarm, it is
because it has been triggered. Thisflashing will stop on switching on theignition.
* According to specification.