display Peugeot 307 Break 2002.5 User Guide

09-09-2002
Instrument panel display
After switching on the ignition, three functions are shown in succession:
service indicator (see corresponding section),
engine oil level indicator,
total distance recorder (total and trip distances).
Note : the total and trip distances are displayed for 30 seconds wh en the ignition
is switched off, on opening the driver's door, as well as on locking and unlocking
the vehicle.
Engine oil level indicator
When the ignition is switched on, the engine oil level is indicated for approxi
mately 10 seconds, after the servicing information.
Maximum
Check the level using the dipstick to confirm whether the displ ay
is correct; a surplus of oil can cause damage to the engine.
Contact a PEUGEOT dealer without delay.
Minimum
Check the level with the dipstick and top it up. The figu re shown
is only correct if the vehicle has been on stable, level ground , with
the engine stopped, for 10 minutes.
Oil level gauge fault
Flashing of the segments, the square or of "min" and "max" indi
cates a fault in the oil level gauge.
There is a risk the engine will be damaged.
Contact a PEUGEOT dealer. Lighting rheostat
With the lights on,
press the button to
vary the intensity of
the lighting of the
instrument panel and
the multifunction dis
play. When the light
ing reaches the minimum (or maxi
mum) setting, release the button
then press it again to increase (or
reduce) the brightness.
As soon as the lighting is of the
required brightness, release the but
ton.
Trip recorder zero
reset
With the ignition on,
press the button.
INSTRUMENTS AND CONTROLS
34

09-09-2002
YOUR 307 IN DETAIL 35
MULTI–FUNCTION
SCREENS
Presentation
Monochrome screen B
This enables the following informa
tion to be displayed:
the time,
the date,
the outside temperature (the
°C
symbol flashes when there is a risk
of ice),
the radio displays,
the status of the openings (doors,
bonnet...),
the warning (e.g. “Battery charge
fault”) or information (e.g.
“Passenger air bag disarmed”)
messages displayed temporarily
can be cleared by pressing button
1 or 2,
the trip computer (see correspond
ing section).
Monochrome screen CT and
colour screen DT
These two systems are controlled by
the RT3 audio/telephone keypad.
They enable the following informa
tion to be displayed:
–the time,–the date,–the outside temperature (a mes
sage warns you when there is a
risk of ice),
–the audio source displays (radio,
CD, ...),
–the telematic system displays (tele
phone, services, ...),
–the status of the openings (doors,
bonnet, ...),
–the warning (e.g. “Fuel level low”)
and vehicle functions status (e.g.
“Passenger air bag disarmed”)
messages displayed temporarily,
–the trip computer display (see cor
responding section),
–the satellite navigation system dis plays (see corresponding section).
Note: to enable you to use all of your
system’s functions, you have two
CD ROMs: one, “Configuration”, con
tains the software and the various
display and spoken information lan
guages, the other, “Navigation”, con
tains the satellite navigation system
map data. Monochrome screen CT
General menu
Press the
“MENU” button to access
the general menu and select one of
the following applications:–navigation guidance (see section
“Satellite navigation system”),
–trip computer (see corresponding section),
–directory (see “RT3 audio/telephone” section),
–telematics (see “RT3 audio/telephone” section),
–configuration (see correspondingsection).

YOUR 307 IN DETAIL
36
Parameter configuration
Monochrome screen B
Press button
1for two seconds to
gain access to the settings .
Then, each press of this button per
mits scrolling of the various parame
ters.
language of the information dis played,
speed unit (km or miles),
temperature unit (degrees Celcius or Fahrenheit),
time format (12 or 24 hours),
hour,
minute,
year,
month,
day.
Pressing button 2enables you to
change the parameter selected.
Continue pressing the button for
rapid scrolling.
After ten seconds without action, the
screen returns to the usual display,
the modified data are recorded.configuration (see corresponding
section).
map (see section “Satellite naviga
tion system”)
A few definitions
Superimposed display:
a window appears over the current
application for a short while, to
announce a change of status of
another application.
Permanent application:
main application currently in use, dis
played in the main screen window.
Contextual menu:
limited menu associated with the
main application currently in use, dis
played in the main screen window.
Colour screen DT
General menu
Press the
“MENU” button to access
the general menu and select one of
the following applications:
navigation guidance (see section
“Satellite navigation system”),
trip computer (see corresponding
section),
directory (see “RT3 audio/tele
phone” section),
telematics (see “RT3 audio/tele
phone” section),
09-09-2002

YOUR 307 IN DETAIL
36
Parameter configuration
Monochrome screen B
Press button
1for two seconds to
gain access to the settings .
Then, each press of this button per
mits scrolling of the various parame
ters.
language of the information dis played,
speed unit (km or miles),
temperature unit (degrees Celcius or Fahrenheit),
time format (12 or 24 hours),
hour,
minute,
year,
month,
day.
Pressing button 2enables you to
change the parameter selected.
Continue pressing the button for
rapid scrolling.
After ten seconds without action, the
screen returns to the usual display,
the modified data are recorded.configuration (see corresponding
section).
map (see section “Satellite naviga
tion system”)
A few definitions
Superimposed display:
a window appears over the current
application for a short while, to
announce a change of status of
another application.
Permanent application:
main application currently in use, dis
played in the main screen window.
Contextual menu:
limited menu associated with the
main application currently in use, dis
played in the main screen window.
Colour screen DT
General menu
Press the
“MENU” button to access
the general menu and select one of
the following applications:
navigation guidance (see section
“Satellite navigation system”),
trip computer (see corresponding
section),
directory (see “RT3 audio/tele
phone” section),
telematics (see “RT3 audio/tele
phone” section),
09-09-2002

09-09-2002
YOUR 307 IN DETAIL37
For safety reasons, config
uration of the multi–func
tion screens by the driver
must be carried out when
stationary.
CT monochrome screen
The
"Configuration" menu gives
access to the following parameters:
– "Adjust the brightness": video dis play brightness setting.
– "Sound": voice synthesiser setting (for the masculine/feminine voice
parameter: insert the configuration
CD ROM); activation/deactivation
of the spoken commands,
– "International parameters": choice of the display and spoken informa
tion language (German, English,
Spanish, French, Italian, Dutch,
Portuguese: insert the configura
tion CD ROM); date and time set
ting (12 or 24 hour mode, adjust
ment of the minutes on GPS); units
setting (l/100 °C or mpg °F).
DT colour screen
The "Configuration" menu gives
access to the following parameters:
– "Choose colours": selection from the palette of colours available for
display,
– "Adjust the brightness": video display brightness setting.
– "Sound": voice synthesiser setting (for the masculine/feminine voice
parameter: insert the configuration
CD ROM); activation/deactivation
of the spoken commands,
– "International parameters": choice of the display and spoken informa
tion language (German, English,
Spanish, French, Italian, Dutch,
Portuguese: insert the configura
tion CD ROM); date and time
setting (12 or 24 hour mode,
adjustment of the minutes on
GPS); units setting (l/100 °C or
mpg °F).

09-09-2002
Adjusting the bassWhen "BASS" is displayed, press button Eor Fto vary the setting.
"BASS –9" for a minimum bass setting,
"BASS 0" for a normal setting,
"BASS +9" for a maximum bass setting.
Adjusting the treble
When " TREB" is displayed, press button Eor Fto vary the setting.
"TREB –9" for a minimum treble setting,
"TREB 0" for a normal setting,
"TREB +9" for a maximum treble setting.
Adjusting the loudness
This function automatically emphasises bass and treble tones.
Press button Eor Fto switch the function on or off.
Adjusting the front/rear sound distribution (Fader)
When " FA D" is displayed, press button Eor F.
Button Eincreases the volume in the front.
Button Fincreases the volume in the rear.
Adjusting the right/left sound distribution (Balance)
When "BAL" is displayed, press button Eor F.
Button Eincreases the volume on the righthand side.
Button Fincreases the volume on the lefthand side.
Automatic volume correction
This function enables the volume to be automatically adjuste d depending on the level of noise produced by the speed of the
vehicle.
Press buttons Eor F to switch the function on or off.
YOUR 307 IN DETAIL 43

09-09-2002
Manual station search
Press the "MAN" button.
Briefly press button Ior Jto increase or decrease the frequency displayed.
By continuing to press the button in the direction selected, you will obtain continuous scrolling of the frequency.
The scrolling stops at the first station found as soon as the button is released.
Pressing the " MAN" button again returns you to automatic station search.
Manual storing of stations in the memory
Select the station required.
Press one of the buttons " 1" to " 6" for more than two seconds.
The sound stops then becomes audible again, confirming that the station has been stored in the memory.
Automatic storing of FM stations in the memory (autostore)
Audio RB3:press and hold the "BND/AST" button for more than two seconds.
Audio RD3: press and hold button "P" for more than two seconds.
Your radio automatically stores the 6 stations with the stronge st signal in FM. These stations are stored in the FMast wave
band.
If it is not possible to find 6 stations, the remaining memo ries are empty.
Recalling stations stored in the memory
For each waveband, briefly press buttons " 1" to " 6" to recall the corresponding station.
YOUR 307 IN DETAIL 45

09-09-2002
RDS
Using the RDS (Radio Data System) function on FM
Radio Data System allows you to continue listening to the same station, whatever frequency it is using for the region you a re
going through.
Briefly press the " RDS" button to switch the function on or off.
The multi–function display wil show:
"RDS" if the function is selected.
"(RDS)" if the function is selected but not available.
RDS station following
The display indicates the name of the station selected. The radio is continually searching for the station which has the best
reception and which is transmitting the same programme.
Traffic information programme
Press the "TA" button to switch the function on or off.
The multi–function display will show:
" TA " if the function is selected,
"(TA)" if the function is selected but not available.
Any traffic information flash will be given priority, whatever source you are listening to (radio, cassette or CD changer).
If you wish to interrupt a message, press the " TA" button; this switches the function off.
Note: the volume of traffic information announcements is inde pendent of the volume of normal radio listening. You
can adjust it using the volume button. The setting will be stored and will be used when the next messages are broad
cast.
Regional following mode
When they are part of a network, certain stations broadcast regi onal programmes in the various areas they serve. With
regional following mode you can keep listening to the same programme.
Press the " RDS" button for more than two seconds to switch the function on or off.
YOUR 307 IN DETAIL
46

09-09-2002
Manual station search
Press the "MAN" button.
Briefly press button Ior Jto increase or decrease the frequency displayed.
By continuing to press the button in the direction selected, you will obtain continuous scrolling of the frequency.
The scrolling stops at the first station found as soon as the button is released.
Pressing the " MAN" button again returns you to automatic station search.
Manual storing of stations in the memory
Select the station required.
Press one of the buttons " 1" to " 6" for more than two seconds.
The sound stops then becomes audible again, confirming that the station has been stored in the memory.
Automatic storing of FM stations in the memory (autostore)
Audio RB3:press and hold the "BND/AST" button for more than two seconds.
Audio RD3: press and hold button "P" for more than two seconds.
Your radio automatically stores the 6 stations with the stronge st signal in FM. These stations are stored in the FMast wave
band.
If it is not possible to find 6 stations, the remaining memo ries are empty.
Recalling stations stored in the memory
For each waveband, briefly press buttons " 1" to " 6" to recall the corresponding station.
YOUR 307 IN DETAIL 45

09-09-2002
RDS
Using the RDS (Radio Data System) function on FM
Radio Data System allows you to continue listening to the same station, whatever frequency it is using for the region you a re
going through.
Briefly press the " RDS" button to switch the function on or off.
The multi–function display wil show:
"RDS" if the function is selected.
"(RDS)" if the function is selected but not available.
RDS station following
The display indicates the name of the station selected. The radio is continually searching for the station which has the best
reception and which is transmitting the same programme.
Traffic information programme
Press the "TA" button to switch the function on or off.
The multi–function display will show:
" TA " if the function is selected,
"(TA)" if the function is selected but not available.
Any traffic information flash will be given priority, whatever source you are listening to (radio, cassette or CD changer).
If you wish to interrupt a message, press the " TA" button; this switches the function off.
Note: the volume of traffic information announcements is inde pendent of the volume of normal radio listening. You
can adjust it using the volume button. The setting will be stored and will be used when the next messages are broad
cast.
Regional following mode
When they are part of a network, certain stations broadcast regi onal programmes in the various areas they serve. With
regional following mode you can keep listening to the same programme.
Press the " RDS" button for more than two seconds to switch the function on or off.
YOUR 307 IN DETAIL
46