Boot Peugeot 307 CC 2003 User Guide

22-09-2003
YOUR 307 CC IN DETAIL
100
THE RETRACTABLE ROOF Before operating the roof: 
It is advisable to park the vehicle on horizontal ground, it is possible to carry out the operation at a speed below
6 mph (10 km/h).
 Ensure that the screen 1is hooked on (no object must
be placed on the screen or on the hinged covers 2; if
there is luggage in the boot, this must not push thescreen upwards).
 Check that no object has been placed on the rear par-cel shelf.
 Close the boot correctly.
 Turn the ignition switch to the accessories or runningposition (1st or 2nd notch). It is advisable to carry outthe operation with the engine running. Opening the roof: 
Carry out the preparatory operations, indicated opposite.
 Then, pull switch 3until the roof opening operation is
complete, confirmed by an audible signal.
When carrying out this manoeuvre, the four windows
lower, the boot opens, the hinged covers unfold, the rooffolds up and stores itself in the boot, the moving shelf posi-tions itself, then the boot closes. Notes: if you continue to pull button 3once the cycle is
complete, the four windows rise again. The control buttons for the windows become operational again at the end of the roof operation.

22-09-2003
YOUR 307 CC IN DETAIL101
Closing the roof: 
Carry out the preparatory operations, indicated on the previous page.
 Then, press button 3until the roof closing operation is
complete, confirmed by an audible signal.
When carrying out this manoeuvre, the four windows
lower, the boot opens, the moving shelf and the roof unfoldand position themselves, the hinged covers fold, then theboot closes. Note: if you continue to press button 3once the cycle is
complete, the four windows rise again. The control buttons for the windows become operational again at the end of the roof operation. In the case of an electric or hydraulic malfunction of the
roof, it is possible to close the roof manually. Please consult the breakdown procedure described at the end of this handbook.
During roof opening and closing operations, to
avoid any risk of injury, ensure that there is no-one in the proximity of the moving parts.
Operation of the roof is the sole responsibility of
the driver.
To guarantee correct operation, do not release but-ton 3 when the roof is in an intermediate position
(neither completely open or closed). However, in the
event of danger, release the control knob and the
operation will stop instantly. Once the danger hasbeen eliminated, complete the operation.

YOUR 307 CC IN DETAIL113
SUN VISOR WITH
ILLUMINATED COURTESYMIRROR With the ignition on, the mirror is automatically lit up when the flap isopened.COURTESY LIGHTS
1 - Front courtesy light
2 - Map reading lights
3 - Rear courtesy light With the key in the accessories position (1st notch) or with the ignition on, oper- ate the relevant switch. The front and rear courtesy lights come on when the ignition key is removed, on unlocking the vehicle or on opening one of the doors.
They gradually go off after the ignition has been switched on or the vehicle is locked. In addition, when the vehicle is moving, the front and rear courtesy lights flash if
a door or the boot is not closed properly. 
Pressing switch 1switches on the front and rear courtesy lights for a duration
of ten minutes.
 Pressing switch 3switches on the rear courtesy light for a duration of ten min-
utes.
Note: The courtesy lights can be deactivated by pressing switch 1for more than
three seconds. A short press on switch 1switches the courtesy lights on and off.
The map reading lights are not affected by this and may be switched on. To re-activate the lights, press switch 1for more than three seconds.
22-09-2003

22-09-2003
YOUR 307 CC IN DETAIL
116
BOOT LAYOUT
1. Stowing rings
Use the stowing rings located on the boot floor and on the bootrear inner panel to secure yourluggage.
2. Luggage retaining net Hooked onto the stowing rings, thisenables your luggage to besecured.
3. 12 volt accessories socket This is a lighter type socket,installed on the boot side trim onthe left-hand side.
It is supplied with the ignition off.
4. Hooks These two hooks permit hooking of the boot mat cords (refer to theSection "Changing a wheel") andlifting of the screen to protect theparcel shelf.
Signalling triangle* The signalling triangle is secured in the boot.
* According to destination.

22-09-2003
PRACTICAL INFORMATION
132
CHANGING A WHEEL Parking the vehicle 
As far possible, park the vehicle on level, stable and non-slipperyground.
 Apply the handbrake, switch offthe ignition and engage first orreverse gear (position Pfor the
automatic gearbox).
Access to the spare wheel and the jack in the boot  Place the vehicle in the coupŽ position.
 Detach the luggage retaining net.
 Lift the boot mat using the handleand attach the cords to the twohooks located under the bootseal. Tools The following tools are located in a holder in the centre of the sparewheel: 1 -
Wheelbrace.
2 - Centralising tool.
3 - Removable chock.
4 - Jack with handle.
5 - Removable towing eye.
6 - Alloy wheel bolt trim remover. Removing the wheel 
Place the holder and the chock 3
(or chock 3on its own if neces-
sary) under the wheel diagonally opposite to the one to bechanged.
 Remove the trim, using thewheelbrace 1, pulling at the valve
passage hole.
 Loosen the wheel bolts (for vehi-cles fitted with alloy wheels,remove the chrome trims first.See paragraph on "Special fea-tures of alloy wheels").

22-09-2003
PRACTICAL INFORMATION133

Place the jack 4in contact with one
of the four locating points Aon the
sub-frame, (the one which is clos- est to the wheel to be changed).
 Extend the jack 4until its base is
in contact with the ground.Ensure that the centre line of thebase of the jack is directly belowthe locating point Aused.
 Raise the vehicle.
 Unscrew the bolts and removethe wheel.
Fitting a wheel  Position the wheel using the cen- tralising tool to assist you.
 Tighten the bolts by hand andremove the centralising tool.
 Partly tighten the bolts using thewheelbrace 1. 
Fold the jack 4and remove it.
 Fully tighten the bolts using thewheelbrace 1.
 Replace the wheel trim, startingby placing the wheel trim notchopposite the valve, and press iton using the palm of the hand.
 Put the tools and the wheel backin the boot.
Note: a diagram on the holder indi-
cates the location of the tools.
Tighten the spare wheel securing strap to prevent noise and for yoursafety in the event of impact. For your safety, alwayschange the wheel:
Ð on level, stable, non-slippery ground,
Ð with the handbrake on and the ignition switched off,
Ð with first or reverse gear engaged (position Pfor the
automatic gearbox),
Ð with the vehicle chocked. Never go underneath a vehicle that is supported only by a jack(use a ramp). After changing the wheel:
Ð have the tightening of the bolts and the tyre pressure checked by a PEUGEOT dealer as soonas possible.
Ð have the punctured tyre repaired and refit it to the vehi-cle as soon as possible.

22-09-2003
PRACTICAL INFORMATION
136
Direction indicator side
repeaters (WY 5 W amber). 
Push the repeater forwards and
release the assembly.
 Hold the connector and turn thelens a quarter turn.
 Change the bulb. Rear lights
1 - Brake lights (diodes).
2 - Side lights (diodes).
3 - Direction indicators (P 21 W).
4 - Reversing light (P 21 W),
left side.
Fog lamp (P 21 W), right side. Direction indicators 
Remove the 3 bolts of the corre- sponding boot side trim to access
the light (use the 20 Torx TM
adaptor
of tool Clocated in the handbook
pocket),
 Remove the light fixing nut insidethe boot,
 Remove the light,
 Unscrew the bulb holder 5a
quarter of a turn,
 Remove the bulb holder,
 Change the faulty bulb.
Note: When refitting, take care to
position the bulb holder and the light
correctly.
Amber coloured bulbs
(direction indicators andside repeaters), must bereplaced with bulbs ofidentical specification
and colour.
All work on the diode lights must be carried out
by a PEUGEOT dealer.

22-09-2003
PRACTICAL INFORMATION
136
Direction indicator side
repeaters (WY 5 W amber). 
Push the repeater forwards and
release the assembly.
 Hold the connector and turn thelens a quarter turn.
 Change the bulb. Rear lights
1 - Brake lights (diodes).
2 - Side lights (diodes).
3 - Direction indicators (P 21 W).
4 - Reversing light (P 21 W),
left side.
Fog lamp (P 21 W), right side. Direction indicators 
Remove the 3 bolts of the corre- sponding boot side trim to access
the light (use the 20 Torx TM
adaptor
of tool Clocated in the handbook
pocket),
 Remove the light fixing nut insidethe boot,
 Remove the light,
 Unscrew the bulb holder 5a
quarter of a turn,
 Remove the bulb holder,
 Change the faulty bulb.
Note: When refitting, take care to
position the bulb holder and the light
correctly.
Amber coloured bulbs
(direction indicators andside repeaters), must bereplaced with bulbs ofidentical specification
and colour.
All work on the diode lights must be carried out
by a PEUGEOT dealer.

22-09-2003
PRACTICAL INFORMATION137
Number plate lights (W 5 W) 
Insert a thin screwdriver into one of the external holes of the lens.
 Push it outwards to unclip it.
 Remove the lens.
 Change the faulty bulb.
Third brake light (diodes)
Reversing light/fog lamp  unclip the corresponding boot lid trim at two points,
 move the trim aside gently toaccess the bulb holder 6,
 unscrew the bulb holder a quar-ter of a turn,
 remove the bulb holder,
 change the faulty bulb.
Note: When refitting, take care to
position the bulb holder correctly.
All work on the diode lights must be carried out
by a PEUGEOT dealer.

PRACTICAL INFORMATION
148
Moving shelf
Boot lid
Hinged covers Screen
Roof locking bolt
Bleed screw
Boot sill Plastic covers
22-09-2003