Panel Peugeot 307 CC 2003 User Guide

22-09-2003
YOUR 307 CC IN DETAIL
102
THE LIGHTS STALK Front and rear lights Selection is by turning ring
A.
Lights off Side lights Dipped/main beam headlamps Automatic switching on of lights Dipped/Main beam change Pull the stalk towards you. Note:
with the ignition off, if the
driver's door is open, a buzzer sounds if you have left your lights on. Front fog lamps and rear fog lamp Rotate the ring Bforwards
to switch on and backwards to
switch off. The status is confirmedby the light on the instrumentpanel.
Front fog lamps (1st for-wards turn of the ring)
The front fog lamps operate with theside lights and dipped headlamps. When the main beam headlamps are switched on, the front fog lamps are
switched off. They are switched onagain when the main beam head-
lamps are switched off. Front fog lamps andrear fog lamp (2nd for-wards turn of the ring)
Note: to switch off the rear fog lamp
and the front fog lamps, turn the ringtwice backwards.
Note: when the lights are switched
off automatically or when the dipped
headlamps are switched off manual-
ly, the front fog lamps, the rear foglamp and the side lights will remainon (turn the ring backwards to switch
off the front fog lamps. The side
lights will then be switched off). "Follow me home" lighting In poor light or at night, if you leave your vehicle, the side lights anddipped headlamps can be left on forapproximately one minute.
To do this:
Ð place the key in the STOPposi-
tion,
Ð place the lights stalk in the 0posi-
tion,
Ð flash the headlamps,Ð get out of the vehicle and lock it.
In good or rainy weather, both day and night, thefront fog lamps and therear fog lamp are daz-
zling and are prohibited. Do not forget to switch them off when they are no longer needed.

22-09-2003
YOUR 307 CC IN DETAIL
116
BOOT LAYOUT
1. Stowing rings
Use the stowing rings located on the boot floor and on the bootrear inner panel to secure yourluggage.
2. Luggage retaining net Hooked onto the stowing rings, thisenables your luggage to besecured.
3. 12 volt accessories socket This is a lighter type socket,installed on the boot side trim onthe left-hand side.
It is supplied with the ignition off.
4. Hooks These two hooks permit hooking of the boot mat cords (refer to theSection "Changing a wheel") andlifting of the screen to protect theparcel shelf.
Signalling triangle* The signalling triangle is secured in the boot.
* According to destination.

YOUR 307 CC IN DETAIL117
S
: sport programme


: snow programme
P ark: to immobilise the vehicle or start the engine ,
with the handbrake on or off.
R everse: to reverse(select this function with the vehi-
cle stationary, engine at idle).
N eutral: to start the engine and to park, with the hand-
brake on. Note: if function Nis engaged inadvertently while dri-
ving, allow the engine to return to idle before engaging function Dto accelerate.
D rive: for drivingin automatic mode.
M anual: for drivingin manual mode. Moving off
With the engine running, to move off from position
P:
 it is essential to press the
brake pedal to exit position P,
 select function R, D or M, then
gradually release the pressureon the brake pedal; the vehicle
moves off immediately.
You can also move off from positionN :
 release the handbrake, with yourfoot on the brake,
 select function R, D or M, then
gradually release the pressureon the brake pedal; the vehicle
moves off immediately.
WARNING When the engine is at idle, brakes not applied, if function R, D or Mis
selected the vehicle moves evenwithout the accelerator beingpressed. For this reason, do not leave chil-
dren unsupervised inside the vehicle, with the engine running .
When maintenance operations needto be carried out with the engine run-ning, apply the handbrake and selectposition P.
"PORSCHE TIPTRONIC SYSTEM" AUTOMATIC GEARBOX The four speed automaticgearbox offers a choice between the comfort of inte-
gral automatic operation , enhanced by a sportand a snow programme, or the
pleasure of manual gear changing .
Gear selection gate  Move the lever in the gate to select a function. Once the function is selected, the corresponding indicator light appears on
the instrument panel display.
22-09-2003

22-09-2003
YOUR 307 CC IN DETAIL
118
Automatic operation Automatic changing of the
four
gears :
 select function Din the gate.
The gearbox always selects the most suitable gear according to the follow-ing parameters:
Ð the style of driving,
Ð the road profile,
Ð the vehicle load. The gearbox is then operating in auto-adaptive mode, without anyaction on your part.
WARNING Never select function Nwhen the
vehicle is moving. Never select functions Por Runless
the vehicle is stationary.Never change between functions to optimise braking on a slippery sur-face. Notes For immediate maximum acceleration
without touching the gear lever, pressthe accelerator pedal down as far as
it will go (kickdown). The gearbox willautomatically change down or main-tain the gear selected until maximumengine speed is reached. When braking, the gearbox will auto- matically change down in order to
provide efficient engine braking. If you take your foot off the accelera-
tor suddenly, the gearbox will notchange to a higher gear for reasons
of safety.
Sport and snow programme In addition to the auto-adaptive pro- gramme, there are two special pro-grammes. The programme is displayed on the instrument panel screen. Sport programme  Press button Sonce the vehicle
has been started and function D
selected.
The gearbox automatically favours sporty driving and more dynamicacceleration. Snow programme This programme improves starting
and drive when traction is poor.  Press button

once the vehicle
has been started and function D
selected.
The gearbox adapts to driving on slippery roads. Note: you can return to the auto-
adaptive programme at any time.  Press button Sor

again to
switch off the programme you are in. Manual operation Manual changing of the
four gears:
 select function Min the gate,
 push the lever to the +sign to
change to a higher gear,
 pull the lever to the Ðsign to
change to a lower gear.
You can change from position D(dri-
ving in automatic mode) to position M (driving in manual mode) at any
time. Note It is only possible to change from one gear to another if the vehicle speedand engine speed permit. If they donot, the vehicle will operate tem-porarily in automatic mode. When the vehicle is stationary or
moving very slowly, the gearboxautomatically selects gear M1.
Programme S(sport) and

(snow)
do not operate in manual mode.

22-09-2003
YOUR 307 CC IN DETAIL119
Releasing Pull on the handle and press the but- ton to release the handbrake.
Illumination of this warninglight and of the STOPwarn-
ing light, accompanied byan audible signal (while thevehicle is being driven) and
the message "handbrake on" on
the multi-function display, indicatesthat the handbrake is still on or hasnot been properly released.
Operating abnormality Any operating abnormality is indicat- ed by an audible signal, accompa-nied by the message
"Automatic
gear fault" on the multi-function dis-
play, "Ð"and flashing of the Sport
and Snow warning lights on theinstrument panel. In this situation the gearbox operates in downgrade mode (locked in 3rd
gear). You may feel a substantialknock when changing from Pto R
and from Nto R(this will not cause
any damage to the gearbox). Do not exceed 60 mph (100 km/h), keeping within the limit of localspeed restrictions.
Contact a PEUGEOT dealer as soon as possible. HANDBRAKE Applying Pull the handbrake to immobilise your vehicle.
Warning:
when parking on a slope,
direct your wheels towards the pave- ment and pull the handbrake.
If the battery is flat and the lever is in position P, it will
be impossible to change toanother position.

22-09-2003
YOUR 307 CC IN DETAIL119
Releasing Pull on the handle and press the but- ton to release the handbrake.
Illumination of this warninglight and of the STOPwarn-
ing light, accompanied byan audible signal (while thevehicle is being driven) and
the message "handbrake on" on
the multi-function display, indicatesthat the handbrake is still on or hasnot been properly released.
Operating abnormality Any operating abnormality is indicat- ed by an audible signal, accompa-nied by the message
"Automatic
gear fault" on the multi-function dis-
play, "Ð"and flashing of the Sport
and Snow warning lights on theinstrument panel. In this situation the gearbox operates in downgrade mode (locked in 3rd
gear). You may feel a substantialknock when changing from Pto R
and from Nto R(this will not cause
any damage to the gearbox). Do not exceed 60 mph (100 km/h), keeping within the limit of localspeed restrictions.
Contact a PEUGEOT dealer as soon as possible. HANDBRAKE Applying Pull the handbrake to immobilise your vehicle.
Warning:
when parking on a slope,
direct your wheels towards the pave- ment and pull the handbrake.
If the battery is flat and the lever is in position P, it will
be impossible to change toanother position.

22-09-2003
YOUR 307 CC IN DETAIL
124
AIR BAGS The air bags have been designed to maximise the safety of the occupantsin the event of serious collisions.They work in conjunction with the
force-limiting seat belts. The elec-tronic detectors register and analyseany abrupt deceleration of the vehi-cle: if the triggering threshold isreached, the air bags inflate instantlyand protect the occupants of thevehicle. Immediately after the impact, the air bags deflate rapidly so that they donot hinder the visibility of the occu-pants nor their exit if necessary fromthe vehicle. The air bags are not deployed in the case of collisions which are not seri-
ous, for which the seat belt is suffi-cient to ensure maximum protection.The seriousness of a collisiondepends on the nature of the obsta-cle and the speed of the vehicle atthe moment of the collision. Air bags only operate when the ignition is switched on. Note:
the gas escaping from the air
bags can be a minor irritant. FRONT AIR BAGS These are folded in the centre of the steering wheel for the driver and in
the fascia for the front passenger.
They are deployed simultaneously,except in cases where the passen-ger air bag is disarmed. Front air bag fault
If this warning light comes on, accompanied by anaudible signal and the mes-sage "Air bag fault" on the
multifunction display, con-
tact a PEUGEOT dealer to have thesystem checked. Disarming the passenger air bag*
To ensure the safety of your child, it is essential to disarm the pas-senger air bag when you install arear-facing child seat on the frontpassenger seat. Otherwise, thechild would risk being killed orseriously injured if the air bagwere to inflate. 
With the ignition switched off, insert the key into the passengerair bag disarming switch 1, turn it
to the "OFF"position, then
remove the key keeping the slotin this position.
The air bag warning light on theinstrument panel is lit throughout thedisarming process.
* According to destination.

22-09-2003
PRACTICAL INFORMATION
130
CHECKING THE LEVELS Oil level 
Check the level regularly and top
up between changes. The maxi-mum consumption is 0.5 l per600 miles (1,000 km). Check the level with the vehicle level, engine cold, using the oil levelgauge on the instrument panel orthe dipstick.
Dipstick There are two marks onthe dipstick: A=maximum
Never fill past this mark
B= minimum
To maintain the reliability of engines and emissioncontrol systems, the useof additives in engine oilis prohibited.
Oil change According to the information given in
"PEUGEOT SERVICING" .
Note: avoid used oil coming into
prolonged contact with the skin. Viscosity selection In all cases, the oil selected must meet the manufacturer's requirements. Brake fluid level:
Ð The level must always be between
the DANGER and MAXIMUM
marks in the reservoir.
Ð If the level drops substantially, contact a PEUGEOT dealer
immediately.
Fluid change:
Ð must be carried out according to the manufacturer's servicing schedule.
Ð use fluids recommended by the manufacturer, which fulfil DOT4standards.
Note: brake fluid is harmful to health
and very corrosive. Avoid all contactwith the skin. Cooling system Use the fluid recommended by the
manufacturer. When the engine is warm, the tem- perature of the coolant is controlled
by the engine fan. As this fan canoperate with the ignition keyremoved and because the coolingsystem is pressurised, wait for atleast one hour after the engine hasstopped before carrying out anywork. Slacken the cap to the first notch torelease the pressure to prevent anyrisk of scalding. When the pressurehas dropped, remove the cap andtop up the level. Note:
the coolant does not need to
be changed. Used oil Do not dispose of used oil, brake fluid or coolant into drains or into theground. Power steering reservoir  Open the reservoir, with the engine at ambient temperature.The level should always beabove the MIN. mark and closeto the MAX. mark.
Windscreen and headlamp* wash level For best quality cleaning and for your
safety, we would advise that you use
products recommended by PEUGEOT.
* According to destination.

PRACTICAL INFORMATION
138
CHANGING A FUSE The fuse boxes are located in the lower part of the fascia (passengerside) and in the engine compartment. The spare fuses and special pliers
A
are fixed to the inside of the lid of the fascia panel fuse box. Removing and changing a fuse Before changing a fuse, you must establish the cause of the fault andhave it corrected. The fuse numbers are indicated on the fuse box.  Use the special pliers A.
Always change a faulty fuse for one of the same rating. Fascia panel fuses 
Unscrew the screw a quarter of a turn with a coin, then pull thehandle to open the cover andaccess the fuses.
Fuse no. Rating Functions
1 10 A Rear fog lamp.
2Ð Not used.
4 15 A Front electric windows - Roll-over hoops - Retractable roof.
5 15 A Left brake light including trailer.
7 30 A Rear courtesy light, front courtesy light, map reading
lights - 12 V front socket - Glove box lighting.
Correct
PliersAIncorrect
22-09-2003

PRACTICAL INFORMATION
138
CHANGING A FUSE The fuse boxes are located in the lower part of the fascia (passengerside) and in the engine compartment. The spare fuses and special pliers
A
are fixed to the inside of the lid of the fascia panel fuse box. Removing and changing a fuse Before changing a fuse, you must establish the cause of the fault andhave it corrected. The fuse numbers are indicated on the fuse box.  Use the special pliers A.
Always change a faulty fuse for one of the same rating. Fascia panel fuses 
Unscrew the screw a quarter of a turn with a coin, then pull thehandle to open the cover andaccess the fuses.
Fuse no. Rating Functions
1 10 A Rear fog lamp.
2Ð Not used.
4 15 A Front electric windows - Roll-over hoops - Retractable roof.
5 15 A Left brake light including trailer.
7 30 A Rear courtesy light, front courtesy light, map reading
lights - 12 V front socket - Glove box lighting.
Correct
PliersAIncorrect
22-09-2003