Peugeot 406 C 2002 Owner's Manual

01-07-2002
MAINTENANCE OF YOUR 406 COUPE
28
3 -
Windscreen and headlamp
wash reservoir.
4 - Battery.
5 - Air filter. 6 -
Brake and clutch fluid reservoir.
7 - Engine oil filler cap.
8 - Dipstick. 3 litre 24 valve V6 petrol injection engine 1 - Power steering reservoir.
2 - Coolant reservoir.

MAINTENANCE OF YOUR 406 COUPE29
2.2 litre 16V turbo diesel HDI engine 1 -
Power steering reservoir.
2 - Coolant reservoir. 3 -
Windscreen and headlamp
wash reservoir.
4 - Battery.
5 - Air filter. 6 -
Brake and clutch fluid reservoir.
7 - Engine oil filler cap.
8 - Dipstick.
01-07-2002

CHECKING THE LEVELS Engine Checking the oil levelCheck the level regularly and top up between changes. Maximumconsumption is 0.5 litres per 600miles (1 000 km). The oil level should be checked with the vehicle level and the engine cold.There are two marks onthe dipstick: A= maximum
B = minimum
Oil change: according to the manu-
facturer's servicing schedule.
- Dipstick. Never fill past the maxi- mum mark A.
- Oil level gauge on the instrument panel.
Viscosity selection In all cases, the oil selected must meet the manufacturer's require-ments. Oil filter Change the filter regularly according to the servicing schedule. Used oilPrevent used oil from coming into prolonged contact with the skin. Do not dispose of used oil into drains or onto the ground.
To maintain the reliability of engines and emission control systems, theuse of additives in the engine oil isprohibited.
Brakes and clutch Checking the brake and clutch fluid level:
- The level should always be above the DANGER mark on the reser-
voir.
- If the level drops substantially, contact a PEUGEOT dealer imme-
diately.
Fluid change
- must be carried out according to the manufacturer's servicing sche- dule.
- use fluids approved by the manu- facturer, which fulfil DOT 4 stan-dards. Cooling system Use the fluid approved by the manu-
facturer. When the engine is warm, the tem- perature of the coolant is controlledby the engine fan. Because this fancan operate with the ignition keyremoved and because the coolingsystem is pressurised, wait for atleast one hour after the engine hasstopped before carrying out anywork. In the event of a breakdown and to avoid any risk of burns, slacken thecap to the first notch to release thepressure. When the pressure hasdropped, remove the cap and top upthe level.
MAINTENANCE OF YOUR 406 COUPE
30
01-07-2002

Power steering reservoir Open the reservoir with the engine
cold. The level should always beabove the MINI mark, close to theMAXI mark.
Windscreen and headlamp wash reservoir For best quality cleaning and for your
safety, we recommend that you useproducts approved by PEUGEOT(capacity 4.5 litres or 9 litres withheadlamp wash). Battery
At the start of winter, have your bat-
tery checked by a PEUGEOT dealer. Air filter Regular replacement of the filter ele- ment is essential. If you drive in
very dusty conditions, change ittwice as often. Brake pads Brake pad wear depends on the style of driving, in particular forvehicles that are used in town, forshort journeys. It may be necessaryto check the thickness of the padseven between services. Handbrake Where the handbrake travel is too great or there is a reduction in theperformance of the system, thehandbrake should be adjusted, evenbetween services. Have the system
checked by a PEUGEOT dealer. Manual gearbox This does not need an oil change. Check the level according to themanufacturer's servicing schedule. Automatic autoadaptive gearbox This does not need an oil change. Have the level checked by a
PEUGEOT dealer according to themanufacturer's servicing schedule.
MAINTENANCE OF YOUR 406 COUPE
31
Only use products appro-
ved by Automobiles
PEUGEOT.
To ensure best perfor- mance from components
as important as the power stee-ring and the braking system,PEUGEOT selects and offersquite specific products.
01-07-2002

Power steering reservoir Open the reservoir with the engine
cold. The level should always beabove the MINI mark, close to theMAXI mark.
Windscreen and headlamp wash reservoir For best quality cleaning and for your
safety, we recommend that you useproducts approved by PEUGEOT(capacity 4.5 litres or 9 litres withheadlamp wash). Battery
At the start of winter, have your bat-
tery checked by a PEUGEOT dealer. Air filter Regular replacement of the filter ele- ment is essential. If you drive in
very dusty conditions, change ittwice as often. Brake pads Brake pad wear depends on the style of driving, in particular forvehicles that are used in town, forshort journeys. It may be necessaryto check the thickness of the padseven between services. Handbrake Where the handbrake travel is too great or there is a reduction in theperformance of the system, thehandbrake should be adjusted, evenbetween services. Have the system
checked by a PEUGEOT dealer. Manual gearbox This does not need an oil change. Check the level according to themanufacturer's servicing schedule. Automatic autoadaptive gearbox This does not need an oil change. Have the level checked by a
PEUGEOT dealer according to themanufacturer's servicing schedule.
MAINTENANCE OF YOUR 406 COUPE
31
Only use products appro-
ved by Automobiles
PEUGEOT.
To ensure best perfor- mance from components
as important as the power stee-ring and the braking system,PEUGEOT selects and offersquite specific products.
01-07-2002

CHANGING A WHEEL Access to the spare wheel and jack Lift the boot carpet using the lifting hook. Secure the hook behind theboot seal.Tools 1 -
Wheel brace.
2 - Centralising tool.
3 - Trim remover/wheel brace extension.
4 - Jack.
5 - Removable towing eye.
6 - Chrome trim tool
The tool holder supports the boot
floor. Reposition it to prevent anydeformation of the floor when loa-ded.
Tighten the spare wheel securing strap to prevent noise and for yoursafety in the event of a frontalimpact. Removal
- Park the vehicle on level, stable
and non-slippery ground.
- Apply the handbrake, engage first or reverse gear (position Pfor the
automatic gearbox).
- Remove the centre trim.
- Loosen the wheel bolts.For vehicles fitted with alloy wheels, remove the chrome trims beforehand(see the section in this chapter entit-led 'Special features of alloywheels').
MAINTENANCE OF YOUR 406 COUPE
32
01-07-2002

- The jack is fitted with a systemwhich enables it to be folded or
unfolded rapidly.
- Take the jack from the toolkit and close it by pressing the ends A.
- Place the jack at one of the loca- tions Eunderneath the vehicle, as
close as possible to the wheel tobe changed. Unfold it by pulling theends A.
- Extend the jack using the wheel- brace 1and the extension 3.
- Take out a wheel bolt at the top and fit the centralising tool 2.
- Loosen the wheel bolts and remo- ve the wheel. Fitting a wheel
- Position the wheel using the cen-
tralising tool to assist you.
- Tighten the bolts by hand, and remove the centralising tool.
- Partly tighten the bolts using the wheelbrace.
- Fold the jack and remove it.
- Fully tighten the wheel bolts using the wheelbrace.
- Replace the centre trim by pres- sing it with the palm of your hand.
MAINTENANCE OF YOUR 406 COUPE 33
For your safety, always change the wheel:
- on level, stable, non-slipperyground,
- with the handbrake applied,
- with first or reverse gear enga- ged (position Pfor the automatic
gearbox).
Never go underneath a vehicle which is supported only by a jack(use a ramp). After changing the wheel - have the tightening of the bolts and the tyre pressure checkedby a PEUGEOT dealer as soonas possible,
- have the punctured tyre repai- red and refit it to the vehicle assoon as possible.
01-07-2002

MAINTENANCE OF YOUR 406 COUPE
34
Anti-theft bolts* If your wheels are fitted with an anti- theft bolt (one per wheel), the chro-me trim and then the plastic covermust be removed using tool
6, befo-
re unscrewing the bolt using one ofthe two anti-theft sockets (whichwere given to you on delivery of yourvehicle along with the duplicate keysand the confidential card) and thewheel brace 1.
Note: make a careful note of the
code number engraved on the head
of the anti-theft socket. This willenable you to obtain duplicate anti-
theft sockets from a Peugeot dealer.
* According to model and destination.
Special features of alloy wheels Bolt covers Alloy wheel bolts are covered by chrome trims. Use tool
6to remove the trims befo-
re slackening the bolts. Fitting the spare wheel If your vehicle is fitted with a steel spare wheel, when fitting it, it is
nor-
mal , when tightening the bolts, to
notice that the washers do not come
into contact with the rim. The sparewheel is secured by the cone shapeof each bolt. Fitting snow tyres If you fit snow tyres mounted on steel wheels, it is essentialto use special
bolts available from your PEUGEOT
dealer.
01-07-2002

MAINTENANCE OF YOUR 406 COUPE35
CHANGING A BULB
1 - Dipped beam headlamps
2 - Main beam headlamps
Two bulbs
(H7-55W).
- Remove the red plastic cover.
- Press the tab and remove the protective cover corresponding to the faulty bulb.
- Disconnect the connector.
- Press the end of the securing clip to remove it. Change the bulb.
- When fitting, ensure that the direction notches are positioned correctly and that the securing clip is corrrectly fixed.
- Reconnect the connector.
- Replace the protective cover.
3 - Side lights (W 5 W)
Turn the socket using the lever and remove it. Change the bulb.
4 - Direction indicators (PY 21 W)
Turn the bulb holder a quarter turn and remove it. Change the bulb. Notes: only handle H7 bulbs using a dry cloth.
To replace the left-hand bulbs, remove the battery protective cover. Direction indicator repeater (W 5 W)
- Pull the rear section of the transpa-
rent cover and release the assem-
bly.
- Turn the connector a quarter turn and remove it.
- Change the bulb.
Amber bulbs must bereplaced by bulbs of iden-tical specification and
colour.
In certain climatic conditions (lowtemperatures, humidity), the pre-
sence of condensation on theinside of the headlamp glass isnormal ; it disappears a few
minutes after the lights switch on.
01-07-2002

MAINTENANCE OF YOUR 406 COUPE
36
Number plate lights (W 5 W)
Remove the translucent protector.Change the faulty bulb.
Rear lights
1 - Direction indicators (P 21 W).
2 - Reversing lights (P 21 W).
3 - Brake lights/Side lights (P 21/5 W).
4 - Side lights (P 21/5 W).
5 - Fog lamp (P 21 W). These 5 bulbs are changed from inside the boot:
- remove the retaining clips then release the carpet,
- remove the connector by pressing the tab
A,
- remove the bulb holder by squeezing the tabs,
- change the faulty bulb.
01-07-2002