Peugeot 406 C 2002 Manual Online

YOUR 406 COUPE IN DETAIL85
Changing the battery of the remote control The information 'battery flat'is
given by an audible signal accompa- nied by a message on the
multiÐfunction display.
To replace the battery, unclip the casing using a coin at the ring(CR2016/3 volt battery). If the remote control does not work after the battery has been changed,reprogramme the remote control.
Confidential card The confidential card contains the identification code necessary for anywork carried out by a PEUGEOT
dealer on the system. This code ishidden by a film, which should be
removed only if necessary. Keep your card in a safe place, never inside the vehicle. Reprogramming the remote control
 Switch off the ignition.
 Switch the ignition on again.
 Press button Aimmediately.
 Switch off the ignition and remove the remote control key from the
ignition. The remote control is nowworking again.
Key in ignition
A buzzer sounds on opening the dri-
ver's door, if the key has been left inthe ignition.
Locating your car
To locate your car, if you have locked it, in a car park:  press button A.The courtesy
lights come on and the directionindicators flash for a few seconds.
01-07-2002

YOUR 406 COUPE IN DETAIL
86
Make a careful note of the number of each key. This number is coded on the label attached to the key. If the key is lost, your PEUGEOT dealer can rapidly supply you with new keys. The high frequency remote control is a sensitive system.
Do not operate it while it is in your pocket as there is a possibility that it may unlock your vehicle.The remote control cannot operate while the key is in the ignition, even if the ignition is off, except for reprogramming.
However, do not operate the deadlocking system if there is someone inside the vehicle.As a safety measure (when there are children on board), remove the key from the ignition when you leave the vehicle, even for a short time.
Avoid operating the remote control buttons out of range of your vehicle; you run the risk of stopping it from working. It would then be necessary to reprogramme it. When buying a second-hand vehicle:
- check that you have been given the confidential card;
- have the keys memorised by a PEUGEOT dealer to be sure that the keys in your possession are the only ones which can start the vehicle.
Do not make any modifications to the electronic engine immobiliser system.
01-07-2002

THE ALARM SYSTEM Setting and deactivating the alarm The alarm completes the security
equipment for your vehicle. It offerstwo types of protection. ¥ exterior protection: when it is set,
the alarm sounds if a door, the
boot or the bonnet is opened;
¥ interior protection: when it is set,
the alarm sounds if the sensors detect a variation in the air move-
ment inside the vehicle (break-ing of a window) or movementinside the vehicle.
The alarm is also equipped with ananti-tamper function. If an attempt is made to tamper with the wires to the siren, control unit or
the battery, the alarm is triggered:the siren sounds and the headlampscome on. Setting the alarm (interior and exterior protection) Switch the ignition off and get out of the vehicle. Press the locking button of the
remote control key. The doors lock.The direction indicators light for two seconds. The red light on the switch flashes once a second.
5 seconds later, exterior protection is set.
50 seconds later, interior protection is set. Note:
when the alarm is triggered,
the siren sounds for thirty seconds. After the thirty seconds it stops, butthe alarm remains set.
Warning: If, on setting the alarm, a
door, the boot or the bonnet are not
closed correctly, the siren sounds fora moment. If the vehicle is closedcorrectly in the following 45 seconds,the alarm is set and the directionindicators remain on for twoseconds. In all cases, the alarm isset after 45 seconds. Disarming the alarm (interior and exteriorl protection) Press the unlocking button of the
remote control key. The doors unlock.The direction indicators flash for two seconds. The red warning light on the switch goes out. Note:
if the warning light continues
to flash after disarming the alarm, it is a sign that the alarm has been trig-
gered. The flashing will stop whenthe ignition is switched on.
SPECIAL FEATURES 135
01-07-2002

Emergency cut-off (If the remote control is not work- ing)
Unlock the doors with the key.
Open the door.
The alarm is triggered. You have ten
seconds in which to switch it off. ¥ Switch on the ignition.
¥ Immediately press interior protec-tion button 1.
¥ The siren stops and the alarm is disarmed. Selecting the type of protectionLocking without setting the alarm Special precautions
To set the alarm with exterior
protection only. If, while you are away from the vehi- cle, you wish to leave a window par-tially open or a pet inside the vehicle,you need to select exterior protectiononly:
¥ Switch off the ignition.¥ Within the next ten seconds, press
the interior protection button 1until
the light comes on continuously.
¥ Get out of the vehicle.¥ Press the locking button of the remote control.
¥ The doors lock.
¥ The direction indicators come on for two seconds.
¥ The red light on the switch flashes once a second.
To disarm exterior protection only
Press the unlocking button on the remote control. The doors unlock and the courtesy lights come on. The direction indicators flash for two seconds. The red light on the switch goes out. To lock the vehicle without setting the alarm It is the remote control which sets the alarm. Therefore, to lock the vehicle with-
out setting the alarm: use the key.
To recharge or replace the battery: ¥ Switch on the ignition.¥
You have 10 seconds after switching
on the ignition to press the interior protection button 1and hold it down
for two seconds.
¥ The indicator light flashes rapidly for three seconds.
¥
You can now disconnect the battery.
After reconnecting the battery:
¥ Lock, then unlock the vehicle using the remote control.
The alarm will be set the next time the vehicle is locked.
SPECIAL FEATURES
136
Do not make any modi- fications to the alarmsystem.
01-07-2002

THE DOORS Opening the doors from outsideOpening the doors from insideLocking from the inside
To lock, press button
A.
Locking the front doors locks the front doors and the boot.
YOUR 406 COUPE IN DETAIL 87
To make opening of the door easier, the window automatically lowers by a few centimetres. It rises and automatically adjusts itself on closing the door to ensure perfect sealing.
Before carrying out any work which involves disconnection of the bat-
tery, lower the windows to permit opening and closing of the doors.
Warning: If the battery is disconnected, the doors can still be opened. How-
ever, it is imperative that the door is not slammed on closing. Consult your PEUGEOT dealer as soon as possible. SUNROOF
¥ To tilt
Press part Aof the switch. To
close, press part Bof the switch
until the sunroof is completely closed.
¥ To open Press part Bof the switch. To
close, press part Aof the switch
until the sunroof is completelyclosed.
01-07-2002

BOOT Simultaneous locking or unlock- ing of the boot and the doors
Turn the key a quarter turn from Ato
B .
The boot is then controlled by the remote control or the driver's doorlock. Locking the boot only
Turn the key a quarter of a turn from A to C. The boot is then locked,
whatever the action of the remotecontrol or the driver's door lock.
To return to simultaneous operation with the doors: turn the key from Ato
B .
YOUR 406 COUPE IN DETAIL
88
OPENING THE BONNET From inside:
pull the handle on the
left-hand side under the fascia.From outside: lift the catch and
raise the bonnet. Bonnet struts These open the bonnet and hold it open.
To close Lower the bonnet and release it at the end of its travel. Check that thebonnet is properly locked. FILLING WITH FUEL Fill with fuel with the engine switched
off.
To open the fuel filler flap, firmly pull the handle on the floor on the outsideof the driver's seat. If you are filling up your tank, do not
continue after the 3rd cut-off of thepump; this could cause your vehicleto malfunction. The capacity of the tank is approx- imately 15.4 gallons (70 litres).
A filler cap hook is provided on the inside of the fuel filler flap.
01-07-2002

Front and rear fog lamps (2nd rotation ofthe ring forwards)
These operate with the side lightsand the dipped/main beam head-lamps. Note: to switch off the rear fog lamp
and the front fog lamps, turn the ring backwards twice in succession.
THE LIGHTS STALK Front and rear lightsSelection is by turning ring A.
Lights off Side lights Dipped / main beam headlamps Automatic switching on of lights Dipped/main beam change Pull the stalk fully towards you. Note:
with the ignition off, if the dri-
ver's door is left open, a buzzer sounds if you have left your lights on.
Front fog lamps and rear fog lamp(ring B) Rotate the ring forwards to switch on
and backwards to switch off. The sta-tus is confirmed by the indicator lighton the instrument panel. Front fog lamps (first rota-tion of the ring forwards)
These operate with the side lightsand the dipped/main beam head-lamps. Direction indicators(flashers)
Left: downwards.
Right: upwards.
YOUR 406 COUPE IN DETAIL 99
In good or rainy weather, both day and night, therear fog lamp is dazzlingand is prohibited.
Do not forget to switch the foglamp off when it is no longerneeded.
01-07-2002

AUTOMATIC SWITCHING ON OF THE LIGHTS Side lights and dipped beam head- lamps switch on automatically if the
light is poor, or during continuousoperation of the windscreen wipers.
They switch off as soon as the lightbecomes bright enough or the wind-screen wipers stop. This function is active when the vehi-
cle is supplied to the customer.
To disarm or activate the function: Place the key in the accessories position (1st notch),
 Press the end of the lights stalkfor more than two seconds.
Note: In foggy weather, the bright-
ness sensor can detect sufficientlight. Because of this, the lights do
not come on automatically. Do not cover the brightness sen-
sor connected to the rain sensor,located in the windscreen behind
the mirror. It is used for automaticswitching on of the lights. Operating check Activation Activation of this function is accom- panied by an audible signal and themessage
"Automatic lighting of
the headlamps activated" on the
multi-function display. Note: Always operate the lighting
controls manually where this is pos- sible. Disarming Disarming of the function is accom- panied by an audible signal. When driving, if this function is
switched off when the headlampswould switch on in automatic mode,the lights remain on. It is however possible to disarm this
function and switch off the lights by:
- manually switching off the lights using the lights stalk,
- switching off the engine. If the brightness sensor does not
function correctly,
the system acti-
vates the function (the lights comeon). The driver is alerted by the flashingof the ''dipped beam'' warning lighton the instrument panel.
Contact a PEUGEOT dealer to have the system checked. Follow me Home When there is a low level of bright- ness or at night, if you leave yourvehicle, the side lights and thedipped beam lights may remain onfor approximately one minute.
To do this: place the lights stalk in the AUTO
position,
 place the key in the accessories position (first notch),
 press the end of the lights stalk formore than two seconds,
 place the lights stalk in the 0posi-
tion,
 flash the headlamps,
 get out of the car and lock it.
YOUR 406 COUPE IN DETAIL
100
01-07-2002

THE WIPER STALK
Windscreen wipers2 Fast wipe (heavy rain).
1 . Normal wipe (moderate
rain).
AUTO Automatic wipe.
0 .Off.


. Single wipe (press the stalk
downwards). Operation In position 1 or 2, when the vehicle stops, the windscreen wiper changesto a lower wiping speed, thenresumes its initial speed when thevehicle starts again. When the ignition has been switched off for more than a
minute with the stalk in the AUTOposition, it is necesary to reacti-vate this function.
To do this, move
the stalk to any position, then move itback to the AUTOposition.
YOUR 406 COUPE IN DETAIL 101
Do not cover the rain detector located on thewindscreen behind the
interior mirror.
When using an automatic carwash, switch off the ignition orcheck that the wiper stalk is not inthe automatic position.
In winter, it is advisable to wait for the windscreen to completelyclear of ice before operating theautomatic wipe.
Windscreen and headlamp wash Pull the windscreen wiper stalk towards you. The windscreen wash then the wind- screen wipers operate for a fixed
period. The windscreen wash andheadlamp wash operate simultane-ously for a few seconds, only if the
dipped beam or main beam head-lamps are on.
Automatic wipe In the
AUTOposition, the wiper
operates automatically and adjusts
its speed to the intensity of the rainfall. Operating check ActivationActivation of the function is accom- panied by the message "Automatic
wiper activated" on the multiÐfunc-
tion display. In the event of malfunction in the
AUTO position, the windscreen
wiper will operate in down-grade mode. Have the system checked by a
PEUGEOT dealer.
01-07-2002

THE TRIP COMPUTERDisplay B Display C
-the date,
-the range,
-the distance travelled,
-the average consumption,
-the current consumption,
-the average speed.
Zero reset Press the button for more than two seconds. Each successive press of the button on the end of the wiper stalk displays in turn:
-the current consumption and the range,
-the average consumption, the distance travelled and the average speed calculated over a period
"1",
-the average consumption, the distance travelled and the average speed calculated over a period "2".
Periods "1"and "2"are defined by the frequency of the zero
reset. They allow, for instance, daily calculations over period"1" and monthly calculations over period "2".
Zero reset When the required period is displayed, press the stalk for more than two seconds.
YOUR 406 COUPE IN DETAIL 113
01-07-2002