light Peugeot 607 Dag 2002 Owner's Guide

YOUR 607 IN DETAIL
90
1 Driver's side
adjustment
2 Passenger's side adjustment
The required value is
displayed (from 15 to
30: comfort value = 22).
 Press the corresponding top and
bottom arrows to adjust.
3 Driver comfortprogramme
4 Passenger comfort
programme
 Press the 'AUTO'button(s).
The system adjusts automatically to
the required value .
It also controls the air distribution,
flow and intake so that there is suffi
cient air circulation in the passenger
compartment.
The air flow (fan) symbol and the
'AUTO' symbols are displayed.
Note: when programme 5or function
11 (following pages) are being used,
the 'AUTO' passenger button does
not operate; it causes temporary
flashing of button 5or 11 indicator
light.
AUTOMATIC AIR CONDITIONING
Located on the centre console, the control panel is between
the multifunction
display and the audio system.
The driver and front passenger can each adjust the temperature a nd the air dis
tribution, to suit their requirements.
Do not cover the sunshine / brightness sensor located i n the centre of the
fascia. It helps to regulate the air conditioning, automati c switching on of
the lights and the automatic adjustment of the instrument pane l bright
ness.

YOUR 607 IN DETAIL91
Manual adjustment Y
ou may, if you wish, make a differ
ent selection from the one offered by
the system, by manually modifying a
setting.
 Pressing the 'AUTO'driver or
passenger button enables you to
return to the corresponding auto
matic operation.
6 Adjustment ofthe driver's air
distribution
7 Adjustment of the passenger's
air distribution
 Pressing the dri
ver's or passenger's
button several times in
succession allows you to position the
air flow on the driver's or passen
ger's side, towards:
– the windscreen and the feet,
– the feet,
– the centre vent, the side ventand the feet,
– the centre vent and the side vent,
– the windscreen. Note:
when programme 5(following
page) is being used, button 7does
not operate; it causes temporary
flashing of the button 5indicator
light.
8 Air conditioning (A/C) on/off
 Press this button
once to stop the air
conditioning.
The symbol 'A/C'goes out.
 Press this button again to return to
automatic air conditioning.
The symbol 'A/C' comes on.
5 Visibility
programme
In certain cases, the
comfort programme
may prove inadequate
to demist or deice the
windows (humidity,
many passengers, ice).
 In this situation, select the visibili
ty programme for rapid clearing of
the windows.
It manages the air conditioning and
the air flow and intake and distrib
utes the ventilation towards the
windscreen and the side windows.
The symbols 'A/C', 'AUTO' and air
flow (fan) are displayed.
Note: for your comfort, between two
starting operations the settings are
retained if the temperature of the
passenger compartment has not var
ied a great deal. If it has, automatic
mode is used.

Flashing of the points in
the temperature setting
values indicates that
there is a malfunction of
the air conditioning. Contact your
Peugeot dealer.
11 Air intake/Recir
culation
 Press this button to
recirculate the inte
rior air.
Recirculation insulates
the passenger com
partment from outside smells and
smoke.
Avoid prolonged operation of inte
rior air recirculation (risk of con
densation and deterioration of air
quality).
 Press this button again to return
air intake to automatic control.
YOUR 607 IN DETAIL
92
12 Demisting the
rear screen
 Press this button,
with the engine
running, to demist
the rear screen and
the mirrors.
Demisting stops automatically after
fifteen minutes.  Press again to resume demisting.
If the engine is switched off before
the end of the fifteen minutes,
demisting will resume when the
engine is switched on again.
Note: it is possible to stop demisting
before it goes off automatically, by
pressing the button again.
Note: the condensation created by
the air conditioning system causes a
flow of water under the vehicle when
stationary, which is perfectly normal.9 Switching off the system
 Press the 'OFF'
button.
This action switches
off the display and the
indicator lights and disarms all the
system functions, with the exception
of demisting of the rear screen.
 Press this button, button 5or one
of the two 'AUTO' buttons again to
reactivate the system with the val
ues which were present before it
was switched off.
10 Air flow Press buttons '+'
and ''respectively
to increase or
decrease the air
flow.
As the air flow is
adjusted, the inner sections of the air
flow symbol (fan) are filled in accord
ingly on the
display.

YOUR 607 IN DETAIL
100
SEAT BELTS
Front seat belt height adjustment:
 To lower the attachment point,
squeeze control 1and slide it
downwards.
 To raise the attachment point,
squeeze control 1and slide it
upwards.
To lock the seat belts  Pull the strap, then insert the end
into the buckle. Front seat belts with
pretensioner and force limiter
Safety in the event of a frontal impact
has been improved by the introduc
tion of seat belts with pretensioner
and force limiter connected to the
front air bags. Depending on the
seriousness of the impact, the pre
tensioning system instantly tightens
the seat belts firmly against the bod
ies of the occupants.
The pretensioning seat belts are
armed when the ignition is on.
The force limiter reduces the pres
sure of the seat belt on the body of
the occupant in the event of an acci
dent.
Rear seat belts with force limiter
The rear seats are all fitted with a
threepoint inertia reel seat belt.
Third rear central seat belt
– pull the belt located between the
two head restraints at the left rear,
– insert the fixed buckle in the black clasp located on the left,
– insert the sliding buckle in the red and black (movable) clasp. To
release it, press the black button of
the locking clasp.
To be effective, a seat
belt must be tightened as
close to the body as pos
sible.
Depending on the nature and seri
ousness of the impact, the pre
tensioners may be triggered
before and independently of the
air bags.
In all cases, the air bag warning
light comes on.
After an impact, have the system
checked by a PEUGEOT dealer.
The system has been designed to
be fully oper ational for ten years.
Have it replaced after this period.

YOUR 607 IN DETAIL101
THE
REMOTE CONTROL KEY
From the driver's door, the key
allows you to lock or unlock the
doors, the boot and the fuel filler flap,
as well as to fold back and unfold the
exterior mirrors.
The remote control in the key per
forms the same functions at a dis
tance.
If one of the front doors or the boot is
open, the central locking does not
function.
Selective unlocking with the
remote control key
This function must be initialised by a
PEUGEOT dealer.
Press button Bto unlock the driver's
door as well as to fold out the exteri
or mirrors.
Press button Bagain to unlock the
other doors, the boot and the fuel
filler flap. Folding/opening out the key
To tuck away the key blade, fold it
down into the remote control mod
ule.
To open out the key, press button
D.
Deadlocking
This renders the internal and exter
nal door controls inoperative, and
enables automatic closing of the win
dows and the sunroof.
With the key  Lock the vehicle and keep the key
in the locking position for approxi
mately one second.
With the remote control incorpo
rated in the key  Press button Aonce to lock the
vehicle (the direction indicators
come on for approximately two
seconds).
 Within a maximum of five sec
onds, press button Aa second
time to deadlock the vehicle (the
direction indicators come on for
approximately two seconds).
Opening the boot with the
remote control key
 Press and hold down button C.
Note: this also unlocks the doors or
the driver's door only, if selective
unlocking is initialised.
Unlocking with the remote
control key
 Press button B.
This is confirmed by rapid flashing of
the direction indicators.
Locking with the remote
control key
 Press button A.
This is confirmed by fixed lighting of
the direction indicators for approxi
mately two seconds.
If one of the doors or the boot is
open, the central locking does not
function.
Note: the function that controls fold
ing back of the exterior mirrors can
be disarmed by a PEUGEOT dealer.

Electronic engine immobiliser
This locks the engine control system
a few moments after the ignition has
been switched off and therefore pre
vents starting of the vehicle by any
one who does not have the key.
The ignition key has an electronic
chip which has a special code. When
the ignition is switched on, the code
is recognised and starting is possi
ble.
If the system does not function
correctly, the central locking button
indicator light, situated on the centre
console, flashes rapidly when the
ignition is switched on (2nd notch).
WARNING: your vehicle is no longer
protected in this event.
Contact a PEUGEOT dealer as soon
as possible. Flat battery
(CR 2025/3 volt battery)
This is indicated by illumination of a
warning light on the instrument panel
display, accompanied by an audible
signal and a message on the multi
function display.
Contact a PEUGEOT dealer to
replace the battery.
YOUR 607 IN DETAIL
102
Key in ignition
A buzzer sounds on opening the dri
ver's door, if the key has been left in
the ignition. Locating your car
To locate your car in a car park:
 press button A; the courtesy lights
come on and the direction indica
tors flash for a few seconds.
Programming the
remote control
in the key  Switch off the ignition.
 Switch the ignition on again.
 Immediately press button A.
 Switch off the ignition and remove
the remote control key from the
ignition lock. The remote control
key is now working again.
Confidential card
The confidential card contains the
identification code necessary for any
work carried out by a PEUGEOT
dealer on the system. This code is
hidden by a film which should be
removed only if necessary.
Keep your card in a safe place,
never inside the vehicle.

Electronic engine immobiliser
This locks the engine control system
a few moments after the ignition has
been switched off and therefore pre
vents starting of the vehicle by any
one who does not have the key.
The ignition key has an electronic
chip which has a special code. When
the ignition is switched on, the code
is recognised and starting is possi
ble.
If the system does not function
correctly, the central locking button
indicator light, situated on the centre
console, flashes rapidly when the
ignition is switched on (2nd notch).
WARNING: your vehicle is no longer
protected in this event.
Contact a PEUGEOT dealer as soon
as possible. Flat battery
(CR 2025/3 volt battery)
This is indicated by illumination of a
warning light on the instrument panel
display, accompanied by an audible
signal and a message on the multi
function display.
Contact a PEUGEOT dealer to
replace the battery.
YOUR 607 IN DETAIL
102
Key in ignition
A buzzer sounds on opening the dri
ver's door, if the key has been left in
the ignition. Locating your car
To locate your car in a car park:
 press button A; the courtesy lights
come on and the direction indica
tors flash for a few seconds.
Programming the
remote control
in the key  Switch off the ignition.
 Switch the ignition on again.
 Immediately press button A.
 Switch off the ignition and remove
the remote control key from the
ignition lock. The remote control
key is now working again.
Confidential card
The confidential card contains the
identification code necessary for any
work carried out by a PEUGEOT
dealer on the system. This code is
hidden by a film which should be
removed only if necessary.
Keep your card in a safe place,
never inside the vehicle.

THE ALARM
This provides two types of protec
tion, exterior and interior:
– exterior protection: when this is set, the alarm sounds if a door, the
boot or the bonnet is opened.
– interior protection: when this is set, the alarm sounds if the sensors
detect a variation in the air move
ment inside the vehicle (breaking
of a window or a movement inside
the vehicle).
Setting the alarm
Switch off the ignition and get out
of the vehicle.
Set the alarm within five minutes
of getting out of the vehicle, by
locking or deadlocking using the
remote control (button Bindicator
light flashes once per second). Note:
if you wish to lock your vehicle
without setting the alarm, use the
door lock.
When the alarm is triggered, the
siren sounds and the direction indi
cators flash for thirty seconds.
It then stops, but the alarm remains
set.
Warning: if the alarm has been trig
gered ten times in succession, on
the eleventh time it becomes inac
tive.
Note: if button B flashes rapidly, the
alarm has been triggered while you
were away from your vehicle.
Automatic activation
The alarm is activated automatically
two minutes after the door or boot
were last closed.
In order to avoid accidental trigger
ing of the alarm when a door or the
boot is opened, it is essential to
press the remote control opening
button first.
Disarming
Unlock the vehicle with the remote
control key (button Bindicator light
goes out).
Note: if the alarm has been triggered
while you were away from your car,
the rapid flashing of the indicator
light will stop when you switch on the
ignition. To set the alarm with exterior
protection only
If, while you are away from the vehi
cle, you wish to leave a window par
tially open or a pet inside the vehicle,
you should choose exterior protec
tion only.
Switch off the ignition
In the next ten seconds, press
button
Auntil indicator light B is
on continuously.
Get out of the vehicle.
Set the alarm by locking or dead
locking using the remote control
switch ( button Bindicator light
flashes once a second).
Note: when the alarm is set but the
remote control does not operate:
Unlock the doors with the key and
open the door. The alarm is trig
gered.
Switch on the ignition in the next
ten seconds. The alarm is disar
med.
Incorrect operation
When the ignition is switched on, if
button Blights for ten seconds, there
is a fault in the siren connection.
Contact a PEUGEOT dealer to have
the system checked.
YOUR 607 IN DETAIL
104

Child safety
This prevents either of the rear doors
being opened from inside. Turn the red plastic switch a quar
ter of a turn using the ignition key.
YOUR 607 IN DETAIL 105
DOORS
Opening the doors
from outside
Opening the doors
from insideLocking / unlocking from the
inside
– Using button
Aof the centre con
sole :
This allows the doors, the boot and
the fuel filler flap to be locked or
unlocked.
– Using button B on the door :
• on the front doors this allows the doors, the boot and the fuel filler
flap to be locked or unlocked.
• on the rear doors this allows the door concerned to be locked or
unlocked.
Note : button Bis neutralised if the
vehicle is deadlocked.
' Door open' alert
With the ignition on (2nd notch), with
the engine running or when the vehi
cle is moving, if a door is not proper
ly closed then the door open warning
light comes on, accompanied by an
audible signal and a diagram indicat
ing the relevant door on the
multi–function display, if a door is not
properlyclosed.

Vehicle unlocked
 Press and hold button Cof the
remote control key or press push
button A.
Note: pushbutton Acan be deacti
vated. Rotate control B,located
inside the boot lid, a quarter of a turn
(anticlockwise) using the key.
YOUR 607 IN DETAIL
106
THE BOOT
Opening the boot
With the vehicle locked / deadlocked

Press and hold button Cof the
remote control key.
This action will also unlock the doors
and the fuel filler flap. SUNROOF
Control the sunroof:
– manually
: lightly press the switch;
the roof stops as soon as the
switch is released.
– automatically : press the switch
down; the roof opens partially or
opens or closes completely
depending on where the switch is
pressed.
– to partially open the roof: press
part Aof the switch. To close it,
press part Bof the switch.
– to open the roof completely: press part Bof the switch.
– to close it completely: press part
A of the switch .
– safety autoreverse When the sunroof is closing and
meets an obstacle, it stops then
opens again.
Note: the sunroof shutter is manual.
Closing the boot
 Press the centre of the boot lid
with both hands, until it locks.
'Boot open' warning
With the ignition on (2nd notch), with
the engine running or when the vehi
cle is moving, the door open warning
light comes on, accompanied by an
audible signal and a diagram on the
multifunction display, if the boot is
not properly closed.