lock Peugeot Boxer 2008.5 Owner's Guide

141
TROUBLESHOOTING
8
REAR LIGHTS
For further information concerning the bulbs,
refer to the table "Types of bulb". - Remove the two fixing nuts.
- Pull the lens block from the outside.
- Unscrew the three screws using the
screwdriver supplied (under the front
passenger seat) and extract the bulb
holder.
- Remove the faulty bulb by pressing it lightly while turning it anticlockwise.
- Change the bulb.

1. Brake/side lights

Type B, P 21/5 W - 5 W

Type B, P 21 W - 21 W
- Unscrew the two screws.
- Remove the light.
- Remove the bulb holder moving aside the two tabs.
- Remove the faulty bulb by pressing it lightly while turning it anticlockwise.
- Change the bulb.

2. Direction indicators

Type B, PY 21 W - 21 W

3. Reversing lights

Type B, P 21 W - 21 W

4. Fog lamps

Type B, P 21 W - 21 W
- Identify the faulty bulb then open the rear doors.
- Disconnect the electrical connector.
NUMBER PLATE LIGHTS

Type A, C5 W - 5 W
- Press the point, indicated by the arrow, then remove the plastic lens.
- Change the bulb by moving aside the two contacts. - Ensure that the new bulbs are secured
correctly between the two contacts.
- Replace the plastic lens and press on it.

Changing a fuse
143
TROUBLESHOOTING
8
PASSENGER’S SIDE FASCIA PANEL FUSES
- Remove the bolts and tilt the box to access the fuses.

Fuses A (amps)
Allocation
12 7 . 5 Right-hand dipped headlamp
13 7 . 5 Left-hand dipped headlamp - Headlamp height adjust er
31 7 . 5 Relay supply
32 10 Minibus interior lighting - Hazard warning lights
33 15 Rear 12 V socket
34 - Not used
35 7 . 5 Reversing lights - Water in diesel sensor
36 15 Door locking/unlocking unit
37 7.5 Brake lights switch - Third brake light - Instrume nt panel
38 10 Interior relays
39 10 Audio equipment - Diagnostics socket - Alarm siren - Programmable additional heating controls
40 15 De-icing: rear screen (left-hand side), mirror (pa ssenger side)
41 15 De-icing: rear screen (right-hand side), mirror (d river ’s side)
42 7 . 5 ABS control unit and sensor - ESP sensor - Brake l ights switch
43 30 Windscreen wiper motor
44 20 Lighter - Front 12 V socket
45 7 . 5 Electric window and mirror switches (driver ’s side ) - Passenger electric window
46 - Not used
47 20 Driver ’s electric window motor
48 20 Passenger electric window motor
49 7 . 5 Rain/brightness sensor - Audio equipment - Driver’ s electric window motor - Alarm - Instrument panel controls
50 7 . 5 Air bags and pre-tensioners unit
51 7 . 5 Chronotachograph - Cruise control - Air conditioni ng controls
52 7 . 5 Passenger compartment relays
53 7 . 5 Instrument panel - Rear fog lamps

146
Changing a wiper blade
CHANGING A WIPER BLADE
The sills, located in the lower front panel,
enable you to access the blades and the
wash-wipe nozzles. Changing a front wiper blade
Lift the wiper arm.
Unclip the blade by pressing the button and
remove it by pulling it outwards.
Fit the new blade and ensure that it is
secured correctly.
Push back the wiper arm.
Changing the rear wiper blade
Lift the wiper arm, then unclip the blade and
remove it.
Fit the new blade and push back the wiper arm.

To return the windscreen wipers to their
normal position, switch on the ignition
and operate the wipers stalk. Check that the wash-wipe or headlamp wash
nozzles are not blocked.