key Peugeot Expert VU 2016 User Guide

53
Expert_en_Chap02_ouvertures_ed01-2016
B a c k- u p c o nt r o l (s)
Locking the driver's doorLocking the front passenger door
F open the door.
For mechanically locking and unlocking the doors in the event of a fault with the central locking
system or a battery failure.
If your vehicle has an alarm, it will not
be deactivated/activated on unlocking/
locking the vehicle.
op

ening a door will trigger the alarm,
which can be stopped by switching on
the ignition.
Locking the sliding side door
F If fitted to your vehicle, check that the electric child lock is not on.
F
o
p
en the door.
Unlocking
F Insert the key in the door lock and turn it to the front.
Unlocking
use the interior door handle.
Unlocking
F use the interior door handle.
For more information on the Child lock ,
refer to the corresponding section.
F

I

nsert the key in the door lock and turn it to
the rear. F

R

emove the cap on on the edge of the
d o o r.
F

I

nsert the key into the latch aperture
(without forcing) and turn the assembly.
F

R

emove the key and refit the cap.
F

C

lose the door and check from the outside
that it has locked correctly. F
R
emove the cap on the edge of the door.
F
I
nsert the key into the latch aperture
(without forcing) and turn the assembly.
F
R
emove the key and refit the cap.
F
C
lose the door and check from the outside
that it has locked correctly.
2
Access

54
Expert_en_Chap02_ouvertures_ed01-2016
Changing the battery
Do not throw the remote control
batteries away, they contain metals
which are harmful to the environment.
ta
ke them to an approved collection
point. If the battery is flat, you are
informed by lighting of this warning
lamp in the instrument panel, an audible signal
and a message in the screen.
Reinitialisation
Locking the side-hinged doors
F If fitted to your vehicle, check that the
electric child lock is not on.
F
o
p
en the left-hand door. Battery ref.: CR1620 / 3 volts.
F
L
ock the driver's door using the
key.
F

P
ress one of the remote control
buttons.
F
t
u
rn the key to position 2 (Ignition on).
F

S
witch off the ignition and remove the key
from the ignition switch.
th

e remote control is fully operational again.
Unlocking
F use the interior door handle.
Remote control problem
Following disconnection of the vehicle battery,
replacement of the remote control battery or
in the event of a remote control malfunction,
you can no longer unlock, lock or locate your
vehicle.
F
F
irst of all, use the key in the lock to unlock
or lock your vehicle.
F
t
hen
reinitialise the remote control.
If the problem persists, contact a PE
u

g
Eo
t
dealer as soon as possible.
F
u
n
clip the cover using a screwdriver in the
cut-out.
F

R
emove the cover.
F

E
xtract the flat battery from its location.
F

P
lace the new battery into its location
observing the original direction.
F

C
lip the cover in place.
F

I

nsert the key into the latch aperture on the
edge of the door (without forcing) and slide
the assembly upward.
F

R

emove the key.
F

C

lose the door and check from the outside
that it has locked correctly.
Access

55
Expert_en_Chap02_ouvertures_ed01-2016
"Keyless Entry and
Starting"
It allows the central locking or unlocking of the
vehicle from a distance.
It is also used to locate and start the vehicle, as
well as providing protection against theft.
Remote control
this separation of cab and loading
area locking provide security in use.
It allows you to prevent access to the
part of the vehicle where you are not
present.
What is the point
of total or selective
unlocking?
total unlocking allows all of the vehicle's doors
(front, side and rear) to be unlocked.
Selective unlocking allows either the cab
doors, or the loading area doors (side and
rear) to be unlocked. F
t
o a
ctivate this selectivity
between cab and loading
area , switch the ignition on and
press this button for more than
2


seconds.
Its indicator lamp comes on.
th

e modification is confirmed by an audible
signal and, depending on equipment, the
display of a message. F
t
o
deactivate this selectivity and
return to total unlocking, switch
the ignition on and press this
button for more than 2
seconds.
Its indicator lamp goes off.
By default, selectivity between cab and
loading area is activated.
Programming
2
Access

59
Expert_en_Chap02_ouvertures_ed01-2016
the unlocking, locking or deadlocking
does not take place:
-
i
f the ignition is on,
-

i
f one of the doors or the boot is still
open,
-

i
f the key for the Keyless Entry and
Starting system has been left inside
the vehicle.
When the vehicle is locked (with the
remote control or Keyless Entry and
Starting), if it is unlocked inadvertently,
it will lock itself again automatically after
about thirty seconds unless a door has
been opened.
And if your vehicle has an alarm, this
will be reactivated (with volumetric
monitoring, even if this had been
deactivated).
"Keyless Entry and
Starting" on your person
this allows the unlocking, locking and starting
the vehicle while keeping the remote control on
your person. As a safety measure (children on
board), never leave the vehicle without
taking your Keyless Entry and Starting
remote control, even for a short period.
gu

ard against theft when the Keyless
Entry and Starting remote control is in
the recognition zone with the vehicle
unlocked.
In order to preserve the charge of the
cell battery in the remote control, the
"hands-free" functions go into extended
stand-by after 21 days of non-use.
to r

estore these functions, press one of
the remote control buttons or start the
engine with the remote control at the
reader.
th
e folding and unfolding of the door
mirrors by the remote control can be
deactivated by a PE
u
g
Eo
t dealer or a
qualified workshop.
In the ignition on (accessories) position,
with the "S
tA
R
t/
S
t
o
P
" button, the
hands-free function is deactivated.
For more information on " Keyless
Entry and Starting " and in particular
the "ignition on" position, refer to the
corresponding section.
2
Access

67
Expert_en_Chap02_ouvertures_ed01-2016
Locating your vehicle
this function allows you to identify your vehicle
from a distance, particularly in poor light. Your
vehicle must have been locked for more than
five seconds.F

P
ress this button
th

is switches on the courtesy lamps and the
direction indicators flash for about ten seconds.
Remote operation of lighting
If fitted to your vehicle.
A short press on this button switches
on the lighting remotely (sidelamps,
dipped beam headlamps and number
plate lamps).
A second press on this button before
the end of the timed period cancels
the remote lighting.
Anti-theft protection
Electronic engine immobiliser
the remote control contains an electronic chip
which has a special code. When the ignition is
switched on, this code must be recognised in
order for starting to be possible.
th

is electronic engine immobiliser locks the
engine management system a few moments
after the ignition is switched off and prevents
starting of the engine by anyone who does not
have the key.
In the event of a fault, you are
informed by illumination of this
warning lamp, an audible signal and
a message in the screen.
In this case, your vehicle will not start; contact
a PE
u

g
Eo
t dealer as soon as possible.
Keep safely, away from your vehicle,
the label attached to the keys given to
you on acquisition of the vehicle.
2
Access

68
Expert_en_Chap02_ouvertures_ed01-2016
B a c k- u p c o nt r o l (s)
If the alarm is activated, the audible
signal triggered on opening a door
with the key (integral with the remote
control) will stop when the ignition is
switched on.
Integral key
Locking the driver's door
Unlocking
F Insert the integral key into the door lock, then turn it to the front.
If your vehicle has an alarm, it will not
be deactivated/activated on unlocking/
locking the vehicle.
op

ening a door will trigger the alarm,
which can be stopped by switching the
ignition on.
to d

eadlock the vehicle, turn the key
again within five seconds of locking.
Locking the front passenger door
F open the door.
Unlocking
F use the interior door handle.
It is used to lock and unlock the vehicle when
the remote control cannot operate:
-

c

ell battery flat, vehicle battery discharged
or disconnected, ...
-

v

ehicle located in an area with strong
electromagnetic signals.
F

P

ress and hold button 1 to extract the
integral key 2 . F

I

nsert the integral key into the door lock,
then turn it to the rear. F
R
emove the cap on on the edge of the
d o o r.
F
I
nsert the key into the latch aperture
(without forcing) and turn the assembly.
F
R
emove the key and refit the cap.
F
C
lose the door and check from the outside
that the vehicle has locked correctly.
Access

69
Expert_en_Chap02_ouvertures_ed01-2016
For more information on the child lock,
refer to the corresponding section.
Locking a sliding side door
F If fitted to your vehicle, check that the electric child lock is not on.
F
o
p
en the door.
Locking the side-hinged doors
F If fitted to your vehicle, check that the electric child lock is not on.
F
o
p
en the left-hand side-hinged door.
Unlocking
F use the interior door handle.Unlocking
F use the interior door handle. F
R
emove the cap on the edge of the door.
F
I
nsert the key into the latch aperture
(without forcing) and turn the assembly.
F
R
emove the key and refit the cap.
F
C
lose the door and check from the outside
that the vehicle has locked correctly. F
I
nsert the key (without forcing) into the
latch aperture located on the edge of the
door and slide the assembly upward.
F
R
emove the key.
F
C
lose the door and check from the outside
that the vehicle has locked correctly.
2
Access

70
Expert_en_Chap02_ouvertures_ed01-2016
Changing the battery
Battery ref.: CR2032 / 3 volts.this replacement battery is available from a
PEugEo t dealer or a qualified workshop.
A message appears in the instrument panel screen
when replacement of the battery is needed.
Do not throw the remote control
batteries away, they contain metals
which are harmful to the environment.
ta

ke them to an approved collection
point.
F

P

lace the remote control against the
reader.
F

K

eeping it in place, switch on the ignition
by pressing "S
tA

R
t/

S
t

o
P

".
th

e remote control is fully operational again.
Reinitialisation
Remote control problem
Following disconnection of the vehicle battery,
replacement of the remote control battery or
in the event of a remote control malfunction,
you can no longer unlock, lock or locate your
vehicle.
F

F
irst, use the integral key in the door lock
to unlock or lock your vehicle.
F
t
hen
, reinitialise the remote control.
If the problem persists, contact a
PE
u

g
Eo
t dealer or a qualified
workshop as soon as possible.
F
u
n
lock the driver's door using the integral
key.
F

P
ress one of the remote control
buttons.
F

P
lace the integral key in the lock to unlock
your vehicle. F
u
n
clip the cover using a small screwdriver
at the cutout.
F

L
ift off the cover.
F

R
emove the flat battery from its location.
F

F
it the new battery into its location
observing the original direction of fitment.
F

C
lip the cover onto the casing.
Access

71
Expert_en_Chap02_ouvertures_ed01-2016
Lost keys, remote control
Visit a PEugEo t dealer with the vehicle's
registration certificate, your personal
identification documents and if possible, the
label bearing the key code.
th

e PE
u
g
Eo
t dealer will be able to retrieve
the key code and the transponder code
required to order a new key
Locking the vehicle
Driving with the doors locked may make
access to the passenger compartment by
the emergency services more difficult in an
emergency.
As a safety precaution (with children on
board), remove the key from the ignition
or take the remote control with you when
leaving the vehicle, even for a short time.
When purchasing a second-
hand vehicle
Have the key codes memorised by a
PEu gEo t dealer, to ensure that the keys in
your possession are the only ones which can
start the vehicle.
Electrical interference
the Keyless Entry and Starting remote
control may not operate if close to certain
electronic devices: telephone, laptop
computer, strong magnetic fields, ... Accumulations (water, dust, grime,
salt...) on the inner sur face of the door
handle may affect detection.
If cleaning the inner sur face of the door
handle using a cloth does not restore
detection, contact a PE
u

g
Eo
t dealer or
a qualified workshop.
A sudden splash of water (stream of
water, high pressure jet washer, …) may
be identified by the system as the desire
to open the vehicle.
Remote control
the high frequency remote control is a
sensitive system; do not operate it while it is
in your pocket as there is a possibility that
it may unlock the vehicle, without you being
aware of it.
Do not repeatedly press the buttons of your
remote control out of range and out of sight
of your vehicle. You run the risk of stopping
it from working and the remote control would
have to be reinitialised.
th

e remote control does not operate when
the key is in the ignition, even when the
ignition is switched off.
Anti-theft protection
Do not make any modifications to the
electronic engine immobiliser system; this
could cause malfunctions.
Do not forget to turn the steering to engage
the steering lock.
2
Access

72
Expert_en_Chap02_ouvertures_ed01-2016
Locking the vehicle
this button is inoperative if the vehicle
has been locked or deadlocked from
outside (using the key, remote control or
Keyless Entry and Starting, according
to equipment) or if one of the doors is
still open.
Automatic
the cabin doors lock automatically while
driving (speed above 6 mph (10 km/h)); the
indicator lamp comes on.When carrying long objects with the
tailgate or rear doors open, you can
press this button to lock just the cabin
doors.
When locking from inside, the door
mirrors do not fold.
th

e indicator lamp also goes off when
unlocking one or more doors.
Driving with the doors locked may make
access to the passenger compartment
by the emergency services more
difficult in an emergency.
F t
o a
ctivate or deactivate this
function, with the ignition on,
press this button until a message
appears in the screen. F

P
ress this button.
F
P
ress this button.
If the vehicle is deadlocked or locked
with the remote control or the door
handles, the button is not active. In this
case, use the key or the remote control
to unlock.
Manual
the indicator lamp comes on to confirm the
locking.th e indicator lamp goes off to confirm the
unlocking.
Unlocking the vehicle
Locking / unlocking from inside
Access