warning light Peugeot Expert VU 2016 Owner's Manual

.
.
Expert_en_Chap00a_sommaire_ed01-2016
over view
Instrument panels 14
Indicator and warning lamps 1 7
Engine coolant temperature
3

1
Distance recorders

3
8
Lighting dimmer

3
9
tr

ip computer
4
0
to

uch screen
4
3
Setting the date and time

4
6
Key
47
K

ey, remote control
4
7
"Keyless Entry and Starting"

5
5
Locking / unlocking from inside

7
2
Front doors

7
4
Manual sliding side door(s)

7
5
Electric sliding side door(s)

7
8
Hands-free sliding side door(s)

87
S

ide-hinged rear doors
9
1
ta

ilgate

94
Alarm
9

5
Electric windows

9
8Steering wheel adjustment
9

9
Front seats
9
9
2-seat front bench seat
1
04
Moduwork

106
Fixed one-piece bench seat
1
10
Fixed rear seat and bench seat
1
13
Fixed crew cab 1 17
Interior fittings 1 19
Loading area fittings

1
22
Seating area fittings

1
23
Heating / Ventilation
1

25
Manual air conditioning
1

26
Dual-zone automatic air conditioning
1

28
Front demist - defrost

1
32
Door mirrors demist - defrost

1
33
Rear screen demist - defrost

1
34
Rear Heating - Air Conditioning

1
37
Programmable Heating / Ventilation

1
38
Courtesy lamp(s)

1
41Mir ror s


143
Lighting control stalk
1
46
Daytime running lamps
1
49
Automatic illumination of headlamps
1
49
Automatic headlamp dipping
1
53
Manual headlamp beam height adjustment
1
55
Wiper control stalk 1 56
Automatic rain sensitive wipers 1 57
Hazard warning lamps
1

60
Emergency or assistance call

1
60
Horn


161
Electronic stability control (ESC)

1
61
gr

ip control
1
64
Seat belts
1

66
Airbags
1

70
Child seats

1
74
Deactivating the passenger's front airbag
1

77
IS
oF

IX mountings
1
86
Manual child lock

1
94
Electric child lock

1
94
Child lock on rear windows

1
95
Eco-driving
Instruments
Access Ease of use and comfort
Lighting and visibility
Safety
Labels 11
Contents

7
Expert_en_Chap00b_vue-ensemble_ed01-2016
Locking/unlocking from inside 7 2-73
Electric sliding d o o r (s)


78 - 8 6
Cabin / loading area selectivity
4

7-48, 55
Electric child lock

1
94
Hazard warning lamps
1

60
Reinitialising the under-inflation detection
26

3-264
Deactivating Stop & Start

2
20
Deactivating the DSC/ASR system
163
Adjusting the steering wheel
9

9
Horn


161
Head-up display
2

22-223
Instruments and controls (cont.)
Wiper c ontrol 15
6 -159tr
ip computer 4 0 - 42
Memorising speeds
2

24
Speed limiter
2

29-231
Cruise control
23

2-235
Dynamic cruise control

2

36 -242
Instrument panel

1

4-16
Warning lamps
1

7-30
Coolant temperature
3

1
Service indicator
3

1-33
oi

l level indicator

3

4
AdBlue
® range indicator 3 5 -37
Distance recorder 3 8
ge

ar shift
indicator

2
08
Lighting dimmer

3
9
tr

ip computer
4
0 - 42
Setting the time and date

4
6
Fatigue detection
2

50-251
Electric windows

9
8
Adjusting the electric mir ror s


143
gr

ip control
16
3, 16 4 -165
Programmable heating / ventilation
1

38-140
Alarm


95-97
Manually adjusting the headlamp beam height
1

55
Lane departure warning system

24
8 -249
Blind spot monitoring system


252-254
Automatic headlamp dipping


153 -15 4 Setting the time and date

4
6
180º Rear vision
2
59 -261
Memorising speeds
2
24
Speed limit recognition 2 25-228, 231, 234, 238
Collision Risk Alert

2
43 -245
Active Safety Brake

2
43, 246 -249
Deactivating Stop & Start

2
20
Lighting control
1

46-151
Direction indicators
1

48
.
over view

29
Expert_en_Chap01_instruments-de-bord_ed01-2016
Warning / indicator lampStateCause Action / Observations
Automatic
wiping fixed.
th

e wiper control has been pushed
down. Automatic front wiping is activated.
to d

eactivate automatic wiping, operate the control
stalk downwards or put the stalk into another position.
Automatic
headlamp
dipping fixed.
th

e lighting control stalk is in
the
"AUTO " position, and the function
has been activated.
th

e main beam headlamps come
on if the exterior lighting and driving
conditions permit.
th

e camera, located at the top of the windscreen,
manages the operation of main beam, depending on
the ambient lighting and driving conditions.
For more information on Automatic headlamp
dipping , refer to the corresponding section.
Stop & Star t fixed. When the vehicle stops (red lights,
traffic jams,
...) the Stop & Start
system has put the engine into S
t

o
P
m

ode.
th
e warning lamp goes off and the engine restarts
automatically in S
tA

R
t
mode, as soon as you want to
move off.
flashes for a few
seconds, then goes
of f. S
t

o
P m
ode is temporarily
unavailable,
or
S
tA

R
t
mode is invoked
automatically. For more information on Stop & Star t
, refer to the
corresponding section.
Blind spot
monitoring
system fixed.
th

e blind spot monitoring system has
been activated. For more information on the Blind spot monitoring
system, refer to the corresponding section.
Lane departure
warning system
fixed.
th

e lane departure warning system
has been activated.
th

e lane departure warning system is on.
For more information on the Lane departure warning
system, refer to the corresponding section.
1
Instruments

30
For more information on the Lighting control stalk, refer to the corresponding section.
Warning / indicator lamp
StateCause Action / Observations
Front foglamps fixed.
th
e front foglamps are switched on
using the ring on the lighting control
stalk.
tu
rn the ring on the lighting control stalk rear ward
once to switch off the front foglamps.
Sidelamps fixed.
th
e lighting stalk is in the
"Sidelamps" position.
Left-hand
direction
indicato r flashing with buzzer.
th
e lighting stalk has been pushed
down.
Right-hand
direction
indicator flashing with buzzer.
th
e lighting stalk has been
pushed

up.
Dipped beam
headlamps fixed.
th
e lighting stalk is in the "Dipped
beam headlamps" position.
Main beam
headlamps fixed.
th
e lighting stalk has been pulled
towards you. Pull the stalk to return to dipped beam headlamps.
Instruments

52
Expert_en_Chap02_ouvertures_ed01-2016
Electronic engine immobiliser
the remote control contains an electronic chip
which has a special code. When the ignition is
switched on, this code must be recognised in
order for starting to be possible.
th
is electronic engine immobiliser locks the
engine management system a few moments
after the ignition is switched off and prevents
starting of the engine by anyone who does not
have the key.
F

P

ress this button
Locating your vehicle
this function allows you to identify your vehicle
from a distance, particularly in poor light. Your
vehicle must have been locked for more than
five seconds.
th

is switches on the courtesy lamps and the
direction indicators flash for about ten seconds.
Remote operation of lighting
A short press on this button switches
on the lighting remotely (sidelamps,
dipped beam headlamps and number
plate lamps).
A second press on this button before
the end of the timed period cancels
the remote lighting.
Anti-theft protection
In the event of a fault, you are
informed by illumination of this
warning lamp, an audible signal and
a message in the screen.
Keep safely, away from your vehicle,
the label attached to the keys given to
you on acquisition of the vehicle.
In this case, your vehicle will not start; contact
a PE
u

g
Eo
t dealer as soon as possible.
If fitted to your vehicle.
Ensure that no person or object could
prevent the correct closing of the
windows.
Be particularly aware of children when
operating the windows. If fitted to your vehicle, pressing
and holding this button allows the
windows to be closed.
t
h

e window
stops when you release the button.
Access

54
Expert_en_Chap02_ouvertures_ed01-2016
Changing the battery
Do not throw the remote control
batteries away, they contain metals
which are harmful to the environment.
ta
ke them to an approved collection
point. If the battery is flat, you are
informed by lighting of this warning
lamp in the instrument panel, an audible signal
and a message in the screen.
Reinitialisation
Locking the side-hinged doors
F If fitted to your vehicle, check that the
electric child lock is not on.
F
o
p
en the left-hand door. Battery ref.: CR1620 / 3 volts.
F
L
ock the driver's door using the
key.
F

P
ress one of the remote control
buttons.
F
t
u
rn the key to position 2 (Ignition on).
F

S
witch off the ignition and remove the key
from the ignition switch.
th

e remote control is fully operational again.
Unlocking
F use the interior door handle.
Remote control problem
Following disconnection of the vehicle battery,
replacement of the remote control battery or
in the event of a remote control malfunction,
you can no longer unlock, lock or locate your
vehicle.
F
F
irst of all, use the key in the lock to unlock
or lock your vehicle.
F
t
hen
reinitialise the remote control.
If the problem persists, contact a PE
u

g
Eo
t
dealer as soon as possible.
F
u
n
clip the cover using a screwdriver in the
cut-out.
F

R
emove the cover.
F

E
xtract the flat battery from its location.
F

P
lace the new battery into its location
observing the original direction.
F

C
lip the cover in place.
F

I

nsert the key into the latch aperture on the
edge of the door (without forcing) and slide
the assembly upward.
F

R

emove the key.
F

C

lose the door and check from the outside
that it has locked correctly.
Access

67
Expert_en_Chap02_ouvertures_ed01-2016
Locating your vehicle
this function allows you to identify your vehicle
from a distance, particularly in poor light. Your
vehicle must have been locked for more than
five seconds.F

P
ress this button
th

is switches on the courtesy lamps and the
direction indicators flash for about ten seconds.
Remote operation of lighting
If fitted to your vehicle.
A short press on this button switches
on the lighting remotely (sidelamps,
dipped beam headlamps and number
plate lamps).
A second press on this button before
the end of the timed period cancels
the remote lighting.
Anti-theft protection
Electronic engine immobiliser
the remote control contains an electronic chip
which has a special code. When the ignition is
switched on, this code must be recognised in
order for starting to be possible.
th

is electronic engine immobiliser locks the
engine management system a few moments
after the ignition is switched off and prevents
starting of the engine by anyone who does not
have the key.
In the event of a fault, you are
informed by illumination of this
warning lamp, an audible signal and
a message in the screen.
In this case, your vehicle will not start; contact
a PE
u

g
Eo
t dealer as soon as possible.
Keep safely, away from your vehicle,
the label attached to the keys given to
you on acquisition of the vehicle.
2
Access

149
Expert_en_Chap04_eclairage-et-visibilite_ed01-2016
Front daytime running
lamps
(light-emitting diodes)
they come on automatically when the engine
is started, when the lighting control stalk is in
position "0" or " AUTO ".
Automatic illumination of
headlamps
Activation
When a low level of ambient light is detected
by a sunshine sensor, the number plate
lamps,


sidelamps and dipped beam headlamps
are switched on automatically, without any
action on the part of the driver.
t
h
ey can also
come on if rain is detected, at the same time as
automatic operation of the windscreen wipers.
As soon as the brightness returns to a
sufficient level or after the windscreen wipers
are switched off, the lamps are switched off
automatically.
Deactivation
F turn the ring to another position. Deactivation of the function is
accompanied by the display of a message.
Operating fault
In the event of a malfunction of the
sunshine sensor, the lighting comes
on; this warning lamp is displayed
Contact a PE
u

g
Eo
t dealer or a qualified
workshop. in the instrument panel accompanied by an
audible signal and/or a message.
In fog or snow, the sunshine sensor
may detect sufficient light. In this
case, the lighting will not come on
automatically.
Do not cover the sunshine sensor,
coupled with the rain sensor and
located in the top of the windscreen
behind the rear view mirror; the
associated functions would no longer
be controlled.
F
t
u

rn the ring to the "AUTO" position.
t
h

e
activation of the function is accompanied
by the display of a message.
4
Lighting and visibility

157
Expert_en_Chap04_eclairage-et-visibilite_ed01-2016
Automatic rain sensitive windscreen wipers
Switching on
Briefly push the control stalk downwards.
A wiping cycle confirms that the
instruction has been accepted.
th
is warning lamp comes on in the
instrument panel and a message is
displayed.
Briefly push the control stalk
downwards again, or place
the control stalk in another
position
(Int, 1 or 2).
th

is warning lamp goes off in the
instrument panel and a message is
displayed.Switching off
the automatic rain sensitive windscreen
wipers must be reactivated by pushing
the control stalk downwards, if the
ignition has been off for more than one
minute.
th

e windscreen wipers operate automatically, without any action on the part of the driver, if rain is
detected (sensor behind the rear view mirror), adapting their speed to the intensity of the rainfall.
Do not cover the rain sensor, linked with
the sunshine sensor and located in the
top of the windscreen behind the rear view
m i r r o r.
Switch off the automatic rain sensitive
wipers when using an automatic car wash.
In winter, it is advisable to wait until the
windscreen is completely clear of ice
before activating the automatic rain
sensitive wipers.
Operating fault
If a fault occurs with the automatic rain
sensitive wipers, the wipers will operate in
intermittent mode.
Have it checked by PE
u

g
Eo
t dealer or a
qualified workshop. Park.
Intermittent wipe.
Wash-wipe (set duration).
Rear wiper
4
Lighting and visibility

158
Expert_en_Chap04_eclairage-et-visibilite_ed01-2016
If a significant accumulation of snow or
ice is present, or when using a bicycle
carrier on the boot, deactivate the
automatic rear wiper.
th
is function is activated by default.
Reverse gear
When reverse gear is engaged, the rear wiper
will come into operation automatically if the
windscreen wipers are operating.
In the vehicle settings menu, activate/
deactivate "
Rear wiper in reverse ".
With the audio system
In the "Personalisation-configuration " menu,
activate/deactivate " Rear wipe in reverse
gear ".
With the touch screen Activation / Deactivation
Activation or deactivation of the function is
done in the vehicle configuration menu.
F

P
ull the windscreen wiper stalk towards
you.
t
he
screenwash then the wipers
operate for a fixed period.
th

e headlamp wash is only activated if the
dipped headlamps are on and the vehicle is
moving .
With daytime running lamps, to activate the
headlamp wash, position the lighting stalk in
the dipped beam position.
Windscreen and headlamp
wash
on vehicles fitted with automatic
air conditioning, any action on the
windscreen wash control results in
temporary closing of the air intake to
avoid odours inside the passenger
compartment.
Screenwash/headlamp wash
level low
In the case of vehicles fitted with
headlamp washers, when the fluid
reservoir low level is reached this
warning lamp comes on in the
instrument panel, accompanied by
an audible signal and a message.
th

e warning lamp comes on when the ignition
is switched on, or every time the stalk is
operated, until the reservoir is refilled.
Next time you stop, refill the screenwash /
headlamp wash reservoir.
Lighting and visibility