radio Peugeot iOn 2018 Owner's Manual
[x] Cancel search | Manufacturer: PEUGEOT, Model Year: 2018, Model line: iOn, Model: Peugeot iOn 2018Pages: 136, PDF Size: 5.79 MB
Page 30 of 136
28
Mats
To take out the driver's side mat, move the seat
back as far as possible and remove the fixings.
To re-install, position it correctly on the pins
and snap on the fixings. Check that the mat is
secured correctly.To avoid any risk of jamming the pedals:
-
O
nly use mats which are suited to the
fixings already present in the vehicle;
these fixings must be used.
-
N
ever place one mat on top of another.
12 V accessory socket
F To connect a 12 V accessory (max. power:
120 W), lift the cover and connect a suitable
adaptor.
The connection of an electrical device
not approved by PEUGEOT, such as a
USB charger, may adversely affect the
operation of vehicle electrical systems,
causing faults such as poor radio
reception or inter ference with displays in
the screens.
Sun visor
Glove box
Never drive with the glove box open when
a passenger is at the front – risk of injury
in the event of sharp deceleration!
The sun visors fold for wards and sideways
when unhooked.
They are fitted with a vanity mirror and ticket
h o l d e r. 4.
Open storage compartment
5. Peugeot Connect USB – USB Player
6. Door pocket
Ease of use and comfort
Page 47 of 136
45
General safety
recommendations
Labels are attached in different places on
your vehicle. They include safety warnings
as well as identification information for
your vehicle. Do not remove them: they
are an integral part of your vehicle.
For any work on your vehicle, use a
qualified workshop that has the technical
information, skills and equipment required,
all of which a PEUGEOT dealer is able to
provide.We draw your attention to the following
points:
-
T
he fitting of electrical equipment
or accessories not listed by
PEUGEOT may cause excessive
current consumption and faults and
failures with the electrical system of
your vehicle. Contact a PEUGEOT
dealer for information on the range of
recommended accessories.
-
A
s a safety measure, access to
the diagnostic socket, used for the
vehicle's electronic systems, is
reser ved strictly for PEUGEOT dealers
or qualified workshops, equipped
with the special tools required (risk
of malfunctions of the vehicle's
electronic systems that could cause
breakdowns or serious accidents).
The manufacturer cannot be held
responsible if this advice is not
followed.
-
A
ny modification or adaptation not
intended or authorised by PEUGEOT
or carried out without meeting the
technical requirements defined by
the manufacturer will result in the
suspension of the legal and contractual
warranties. Installation of accessory radio
communication transmitters
Before installing a radio communication
transmitter, you must contact a PEUGEOT
dealer for the specification of transmitters
which can be fitted (frequency, maximum
power, antenna position, specific
installation requirements), in line with the
Vehicle Electromagnetic Compatibility
Directive (2004/104/EC).
Depending on country regulations, some
safety equipment may be compulsory:
high visibility safety vests, warning
triangles, breathalysers, spare bulbs,
spare fuses, fire extinguisher, first aid kit,
mud flaps at the rear of the vehicle, etc.
5
Safety
Page 105 of 136
103
Fuse No.Rating Functions
14 15 ARear wiper.
15 7. 5 AInstrument panel.
16 7. 5 AHeating.
17 20 AHeated seat.
18 10 AOption.
19 7. 5 ADoor mirrors defrosting.
20 20 AWindscreen wipers.
21 7. 5 AAirbags.
22 30 ARear screen defrosting.
23 30 AHeating.
24 -Not used.
25 10 ARadio.
26 15 APassenger compartment fuse. The fusebox is located in the front
compartment, under the heating system fluid
reser voir. Only these fuses can be replaced.
Replacement of the fuses in other boxes
(vacuum pump and ancillaries battery)
requires the involvement of a PEUGEOT
dealer or a qualified workshop.Fuses in the front
compartment
8
In the event of a breakdown
Page 108 of 136
106
Motor and main battery
Model code:1 N ZK Y Z
Electric motor Y51
Technology Synchronous with permanent neodymium magnets
Max power: EU standard (kW) 49
Max power motor speed (rpm) 4,000 to 8,800
Max torque: EU standard (Nm) 19 6
Max torque speed (rpm) 0 to 300
Main battery Lithium-Ion
Energy capacity when new (kWh) 14.5
Normal charge
Voltage (V) AC 230
Recharging time
(*)(**):
- 16 A
- 14 A
- 10 A
- 8 A Approximately 6
hours
6
hours
8
hours
11
h o u r s
Fast charge
Voltage (V) DC 300
Charging time (80% charge)** 30
minutes
Range varies depending on the exterior climatic conditions, the driver’s driving style, the use of electrical systems, the frequency of normal or rapid
charges, and ageing of the main battery. *
D
epending on the country's electricity grid.
**
T
ime measured for exterior temperatures between 20 and 25°C. Depending on the use of radio equipment and/or air conditioning, recharging time
may increase.
Technical data
Page 113 of 136
1
Bluetooth® audio system
Contents
First steps
1
R
adio 2
Media
3
T
elephone
6
Audio settings
8
C
onfiguration
8
Frequently asked questions
9
F
or safety reasons, the vehicle must
always be stationary for the driver to
perform operations that require close
attention.
When the engine is switched off and to
prevent discharging of the battery, the
system switches off after activation of
energy economy mode. After a battery disconnection, a code must
be entered to access the audio system
functions.
You can try five times at most. There is
approximately fifteen minutes waiting time
between each of the last two tries.
Go to the end of this document to recover
the label indicating the code:
First steps
On/Off, volume adjustment.
Adjust audio options: sound
ambience, treble, bass, loudness,
distribution, left/right balance, front/
rear balance, automatic volume.
Automatic search for a lower radio
frequency.
Select the previous CD, USB track.
Scroll in a list.
Press and hold: rewind.
Display the list of stations received,
the CD/USB tracks or folders.
Press and hold: update the list of
stations received.
Cancel the current operation.
Go up one level (menu or folder).
Automatic search for a higher radio
frequency.
Select the next CD, USB track.
Scroll in a list.
Press and hold: fast for ward.
Access to the main menu.
.
Bluetooth® audio system
Page 114 of 136
2
Select preset radio station.
Radio, press and hold: store a
station.
Other than radio: see the
corresponding sections.
Eject CD.
Select the source:
Radio: FM1, FM2, CD, USB, AUX,
Streaming.
Telephone: accept an incoming call.
Telephone, press and hold: end
a call, access the calls log for the
connected telephone.
Radio
Presetting a station
Press SRC/TEL repeatedly to select
the FM1, FM2 or AM waveband.
Press and hold a button to preset
the station being listened to. The
name of the station is displayed and
an audible signal confirms that it has
been preset. The external environment (hills, buildings,
tunnels, basement car parks, etc.) may
block reception, including in RDS tracking
mode. This is a normal effect of the way
in which radio waves are transmitted and
does not indicate any failure of the audio
equipment.
Selecting a station
Press a button to listen to the
corresponding preset station.
Managing a list
Press LIST
to display the list of
stations received in alphabetical
o r d e r.
Select the desired radio station
using one of the buttons.
Confirm with " OK".
Briefly press one of the buttons to
change to the next or previous letter.
Press and hold LIST to build or
update the list of stations; audio
reception is cut momentarily.
Entering a frequency
Press MENU .
Select "Radio ".
Select "Enter or Write freq. ".
Press + ,
or press – to select the desired
frequency.
Confirm with " OK".
RDS
RDS, if activated, allows you to
continue listening to the same station
by automatically retuning to alternative
frequencies. However, in certain conditions,
coverage of an RDS station may not be
assured throughout the entire country as
radio stations do not cover 100% of the
territory. This explains the loss of reception
of a station that can occur during a journey.
With source FM1 or FM2, press
MENU .
Select "Radio ".
Bluetooth® audio system
Page 115 of 136
3
Select or deselect "RDS " to switch
RDS on or off.
Confirm with " OK" to save the
setting.
Receiving TA messages
The TA (Traffic Announcement) function
gives priority to TA alert messages.
To operate, this function needs good
reception of a radio station transmitting
this type of message. When a traffic
report is transmitted, the current audio
source (radio, CD, USB, etc.) is interrupted
automatically to play the TA message.
Normal playback resumes at the end of
the transmission of the message.
Press MENU .
Select "Radio ".
Select or deselect " TA" to activate
or deactivate the reception of traffic
messages.
Confirm with " OK" to save the
setting.
Displaying RADIO TEXT
Radio Text is information transmitted by
the radio station related to the current
programme or song.
With the radio displayed on the
screen, press MENU .
Select " Radio".
Select or deselect " TXT" to activate
or deactivate the display of Radio
Te x t .
Confirm with " OK" to save the
setting.
Media
USB port
This unit comprises a USB port and a jack
socket, depending on model. The system constitutes playlists (in
temporary memory), whose creation time
can be from a few seconds to several
minutes at the first connection.
Limiting the number of non-music files and
the number of folders reduces this waiting
time. The playlists are updated every
time the ignition is switched off or a USB
memory stick is connected.
The lists are memorised: if there is no
change in the lists, the next loading time
will be shorter.
Connect a USB memory stick to the USB port
or connect a USB device to the USB port using
a suitable cable (not supplied). To protect the system, do not use a USB
hub. Press SRC/TEL repeatedly to select
" USB ".
Press one of these buttons to select
the previous or next track in the list.
.
Bluetooth® audio system
Page 122 of 136
10
QUESTIONRESPONSESOLUTION
There is a difference in sound quality between
the different audio sources (radio, CD, etc.). For optimum sound quality, the audio settings
(volume, bass, treble, ambience, loudness)
can be adapted to the different sound sources,
which may result in audible differences when
changing source (radio, CD, etc.).Check that the audio settings (volume, bass,
treble, ambience, loudness) are adapted to
the sources being listened to. It is advisable to
set the AUDIO functions (bass, treble, front-
rear balance, left-right balance) to the middle
position, select the musical ambience and set
the loudness correction to the "Active" position
in CD mode or to the "Inactive" position in radio
mode.
When changing the settings for treble and bass,
the ambience setting is deselected.
When changing the ambience setting, treble
and bass are reset to zero. Choosing an ambience imposes settings for
treble and bass. Modifying one without the other
is only possible with a personalised ambience.
Modify the treble and bass settings or the
ambience setting to obtain the desired sound
quality.
When changing the balance setting, distribution
is deselected. Choosing the "driver" distribution setting
imposes a balance setting.Modify the balance or distribution settings to
obtain the desired sound quality.
The reception quality of the tuned radio station
gradually deteriorates or the stored stations are
not working (no sound, 87.5
MHz is displayed...).The vehicle is too far from the transmitter of
the station or no transmitter is present in the
geographical area. Activate the RDS function and search for the
station again to enable the system to check
whether there is a more power ful transmitter in
the geographical area.
The surroundings (hills, buildings, tunnels,
underground car park, etc.) are blocking
reception, including in RDS tracking mode. This phenomenon is normal and does not
indicate a failure of the audio equipment.
The aerial is missing or has been damaged (for
example when going through a car wash or into
an underground car park). Have the aerial checked by a PEUGEOT dealer.
Bluetooth® audio system
Page 123 of 136
11
Sound cut-outs of 1 to 2 seconds in radio mode. During this brief sound cut-out, the RDS
searches for any frequency permitting better
reception of the station. Deactivate the RDS function if the phenomenon
is too frequent and always on the same route.
Traffic announcement TA is displayed. I do not
receive any traffic information. The radio station does not broadcast traffic
information.Tune to a radio station which broadcasts traffic
information.
The stored stations are not found (no sound,
87.5
MHz is displayed...). An incorrect waveband is selected.
Press the SRC/ TEL button to return to the
waveband (FM1 or FM2) on which the stations
are stored.
The CD is ejected every time or is not played. The CD is upside down, cannot be read, does not contain audio files or contains audio files
of a format that cannot be played by the audio
system.
The CD is protected by an anti-pirating system
not recognised by the audio system.-
C
heck that the CD is inserted in the player
the right way up.
-
C
heck the condition of the CD: the CD
cannot be played if it is too badly damaged.
-
C
heck the content in the case of a recorded
CD: consult the advice in the "Audio"
section.
-
T
he audio system’s CD player does not play
DVDs.
-
B
ecause of low quality, certain burned CDs
will not be read by the audio system.
The CD sound is of poor quality. The CD used is scratched or of poor quality. Insert good quality CDs and store them in
suitable conditions.
The audio settings (bass, treble, ambiences) are
unsuitable. Return bass and treble settings to 0, without
selecting an ambience.
The Bluetooth connection cuts out. The battery of the peripheral device may not be
sufficiently charged.Charge the battery of the peripheral device.
The "USB peripheral/device error" or "Peripheral/Device
not recognised" message appears on the screen.The USB memory stick is not recognised. Use only USB memory sticks formatted to
FAT 32 (28 -bit file allocation table).
.
Bluetooth® audio system
Page 125 of 136
1
1
2
1
2
KENWOOD – KDC-X7000DAB
As a safety measure, the vehicle must
be stationary when the driver carries
out operations that require sustained
attention.Short press: on.
Long press: off.
Rotate: set the audio volume,
navigate in a list.
Press: confirm.
Change the audio source.
Short press: accept an incoming
call, switch between two calls, enter
Bluetooth mode.
Long press: smartphone voice
commands via the system.
Short press: find a ser vice.
Long press: update list of stations
received.
Abandon the current operation.
Go up one level in the menu.
Reject or end a call.Select an analogue band FM1/FM2/
FM 3 / M W/ LW.
Select a digital band DB1/DB2/DB3.
Navigate in a list.
Change the search method
(automatic or manual).
Fit the control panel.
Remove the control panel. Short press: find a radio station,
frequency or service, find the
previous/next track or file, navigate
in a list.
Long press: fast for ward or rewind.
Short press: select a preset radio
station.
Long press: add a radio station to
presets.
For more information, refer to the KENWOOD
user guide provided with the system.
.
KENWOOD - KDC-X7000DAB