ESP Peugeot RCZ 2011 Owner's Guide

7/
CHECKS






































CHECKING LEVELS

Check all of these levels regularly and top them up if necessary, unless
otherwise indicated.
If a level drops signifi cantly, have the corresponding system checked by
a PEUGEOT dealer or a qualifi ed workshop.


OIL LEVEL

The check is carried out either when the ignition is switched
on using the oil level indicator on the instrument panel, or
using the dipstick.
This manual check will only be correct if the vehicle is on level ground
and the engine has been off for more than 30 minutes.
After topping up the oil, the check when switching on the ignition
with the oil level indicator in the instrument panel will only be valid
30 minutes after topping up.

It is normal to top up the oil level between services. PEUGEOT
recommends that you check the oil level and top up if necessary
every 3 000 miles (5 000 kilometres).


Engine oil change

Refer to the Warranty and Maintenance Record for details of the interval
for this operation.
In order to maintain the reliability of the engine and emission control
system, the use of additives in the engine oil is prohibited.


BRAKE FLUID LEVEL

The brake fl uid level should be close to the "MAX" mark. If it is
not, check the brake pad wear.

Changing the fluid

Refer to the Warranty and Maintenance Record for details of the interval
for this operation.


Fluid specification

The brake fl uid must conform to the manufacturer's recommendations
and meet the DOT4 standard.



POWER STEERING FLUID LEVEL

The power steering fl uid level should be close to the "MAX"
mark. Unscrew the cap, with the engine cold, to check the level.
When working under the bonnet, take care, as certain areas of the
engine may be extremely hot (risk of burns).


Oil specification

The oil must be the correct grade for your engine and conform to the
manufacturer's recommendations.

164








CHANGING A WIPER BLADE


BEFORE REMOVING A WIPER BLADE



)
Within one minute after switching off the ignition, operate the wiper
stalk to position the wiper blades in the centre of the windscreen.



REMOVING



)
Raise the corresponding wiper arm.

)
Unclip the wiper blade and remove it.



FITTING



)
Put the corresponding new wiper blade in place and clip it.

)
Fold down the wiper arm carefully.



AFTER FITTING A WIPER BLADE



)
Switch on the ignition.

)
Operate the wiper stalk again to park the wiper blades.



Access to tools *



)
Open the boot lid.

)
Lift the boot fl oor using its strap.

)
Fix it in the vertical position beyond the stops located on the boot
sides.

)
Remove the temporary puncture repair kit for access to the jack.

* According to country. All of these tools are specifi c to your vehicle. Do not use them for
other purposes.

8/
PRACTICAL INFORMATION

DISCONNECTING/RECONNECTING THE
CABLES

To avoid discharging the battery, do not leave the vehicle lighting
on repeatedly with the ignition off (refer to the "Energy economy
mode" paragraph).
It is advisable to disconnect the battery if the vehicle is to be left
unused for more than one month.

Do not disconnect the terminals while the engine is running.
Do not charge the batteries without disconnecting the terminals fi rst.


Before disconnecting the battery

Wait 2 minutes after switching off the ignition before disconnecting
the battery.
Retract the active spoiler then close the windows and the doors
before disconnecting the battery.


Following reconnection of the battery

Following reconnection of the battery, switch on the ignition
and wait 1 minute before starting to permit initialisation of the
electronic systems. However, if slight problems remain following
this operation, contact a PEUGEOT dealer or a qualifi ed
workshop.
Referring to the corresponding section, you must yourself
reinitialise:


- the remote control key,

- the electric windows and the automatic partial opening of the
door windows,

- the GPS satellite navigation system.



)
Raise the locking tab D
fully.

)
Position the open clip E
of the cable on the positive terminal (+) of
the battery.

)
Press vertically on the clip E
to position it correctly against the
battery.

)
Lock the clip by lowering the tab D
.


CHARGING THE BATTERY USING A BATTERY
CHARGER


)
Disconnect the battery from the vehicle.

)
Follow the instructions for use provided by the manufacturer of the
charger.

)
Reconnect starting with the negative terminal (-).

)
Check that the terminals and connectors are clean. If they are
covered with sulphate (whitish or greenish deposit), remove them
and clean them.

Do not force the tab as locking will not be possible if the clip is not
positioned correctly.
Start the procedure again.

172

Changing brake lamps/sidelamps

This bulb is changed from outside the boot, having fi rst removed the
rear lamp:


)
open the boot lid,

)
unclip the access fl ap of the corresponding side trim, then remove it,

)
unclip the lamp taking hold of it at the base, then tilt it,

)
turn the bulb holder one quarter of a turn and remove it,

)
turn the bulb one quarter of a turn and change it.
To refi t, carry out these operations in reverse order.
)
disconnect the lamp connector,

)
remove the two lamp fi xing bolts,

8/
PRACTICAL INFORMATION

Changing reversing lamps and foglamps

These two bulbs are changed from outside the rear bumper:


)
unclip the protective cover from the rear, then tilt it,

)
remove it completely to gain access to the two lamp fi xing bolts,

On the left-hand side, take care not to touch the silencer; risk
of burns, if you change the bulb immediately after switching
off the ignition.


)
turn these two bolts one quarter of a turn and remove them,

)
push the lamp towards the inside to unclip it, then tilt it,

)
pull the lamp towards the outside for access to the various bulb-
holders.


- For the reversing lamps: pull the corresponding bulb holder,

- turn the bulb one quarter of a turn and change it.


- For the foglamp: turn the bulb holder one quarter of a turn and
remove it,

- turn the bulb one quarter of a turn and change it.

To refi t, carry out these operations in reverse order.

176

Installing electrical accessories

Your vehicle's electrical system is designed to operate with
standard or optional equipment.
Before installing other electrical equipment or accessories on your
vehicle, contact a PEUGEOT dealer or a qualifi ed workshop.
PEUGEOT will not accept responsibility for the cost incurred in
repairing your vehicle or for rectifying malfunctions resulting from
the installation of accessories not supplied and not recommended
by PEUGEOT and not installed in accordance with its instructions,
in particular when the combined consumption of all of the
additional equipment connected exceeds 10 milliamperes.

8/
F10
F11
F13F14F12
F20
F19
F18
F17
F16
F15
F4
F8F2
F3F5 F7
F9
F6
F21 F1
PRACTICAL INFORMATION

ENGINE COMPARTMENT FUSES

The fusebox is placed in the engine compartment near the battery (left-
hand side).

Access to the fuses



)
Unclip the cover.

)
Change the fuse (see corresponding paragraph).

)
When you have fi nished, close the cover carefully to assure the
sealing of the fusebox.



Fuse table



Fuse N°



Rating


Functions



F1



20 A

Engine control unit supply, injection
pump and EGR electrovalves (Diesel),
injectors (Diesel).


F2



15 A

Horn.


F3



10 A

Front wash-wipe.


F4



20 A

Daytime running lamps.


F5



15 A

Air fl ow sensor, coolant pump, oil pump,
thermostat, blow-by heater (petrol),
by-pass and EGR electrovalves (Diesel),
diesel heater (Diesel).


F6



10 A

Steering wheel angle sensor, ABS/ESP
control unit, ESP control unit.


F7



10 A

Power steering control unit, automatic
gearbox, engine coolant level detector,
dual function brake switch.


F8



25 A

Starter motor control.


F9



10 A

Diagnostic socket, directional
headlamps, particle emission fi lter pump
(Diesel).


F10



30 A

Engine control unit actuators (petrol:
ignition coils, electrovalves, injectors,
fuel pump (Diesel: electrovalves,
heaters).


F11



40 A

Air conditioning blower.

8/
F1 F3 F5F2 F4 F6F7
F11F9F8
F12
F10
PRACTICAL INFORMATION

Table of fuses over the battery



Fuse N°



Rating


Functions



F1



-

Not used.


F2



5 A

Dual function brake switch.


F3



5 A

Battery charge unit.


F4



25 A

ABS/ESP electrovalves.


F5



-

Not used.


F6



15 A

Automatic gearbox. All work on the other types of fuses (midi-fuses and maxi-fuses)
must be carried out only by a PEUGEOT dealer or a qualifi ed
workshop.

211
04
2ABC3DEF5JKL4GHI6MNO8TUV7PQRS9WXYZ0*#
1RADIO MEDIANAV ESC TRAFFIC
SETUPADDR
BOOK7
8
9
10
11
2ABC3DEF5JKL4GHI6MNO8TUV7PQRS9WXYZ0*#
1RADIO MEDIANAV ESC TRAFFIC
SETUPADDR
BOOK
2ABC3DEF5JKL4GHI6MNO8TUV7PQRS9WXYZ0*#
1RADIO MEDIANAV ESC TRAFFIC
SETUPADDR
BOOK
2ABC3DEF5JKL4GHI6MNO8TUV7PQRS9WXYZ0*#
1RADIO MEDIANAV ESC TRAFFIC
SETUPADDR
BOOK
2ABC3DEF5JKL4GHI6MNO8TUV7PQRS9WXYZ0*#
1RADIO MEDIANAV ESC TRAFFIC
SETUPADDR
BOOK
Repeat steps 5 to 7 for the "Street"
and "House number" functions.

To delete a destination; from steps 1 to 3, select "Choose from last
destinations".
A long press on one of the destinations displays a list of actions
from which you can select:
Select the "Save to address book" function to record the address
entered in a directory fi le. Press OK to confi rm the selection.
The Peugeot Connect Media allows more than 4 000 contact
records to be saved.
To speed up the process, the post code can be entered directly
after selecting the "Postal code" function.
Use the virtual keypad to enter the letters and digits.

Select the route type:
"Fast route", "Short route", or
"Optimized route" and press OK to
confi rm.
Then select "Start route guidance"
and the press OK to confi rm.


It is also possible to select a destination via "Choose from address
book" or "Choose from last destinations", by selecting a junction, a
town centre, geographic coordinates, or directly on the "Map".

Choose from address book


Choose from last destinations



Start route guidance


It is possible to scroll the map using the 4-direction navigator. It is possible
to select its orientation via the short-cut menu of the "Full screen map".
Press OK then select "Map Settings" and confi rm.

Select the road with the colour
corresponding to the route chosen
and press OK to confi rm and start
guidance.


Turn the ring and select OK.
Press OK to confi rm.


Delete entry

Delete list


NAVIGATION - GUIDANCE

221
06
11
2
NAV ESC TRAFFICRADIOMEDIA
RADIONAV ESC TRAFFICMEDIA
RADIO
2ABC3DEF5JKL4GHI6MNO8TUV7PQRS9WXYZ0*#
1RADIO MEDIANAV ESC TRAFFIC
SETUPADDR
BOOK
2ABC3DEF5JKL4GHI6MNO8TUV7PQRS9WXYZ0*#
1RADIO MEDIANAV ESC TRAFFIC
SETUPADDR
BOOK
2ABC3DEF5JKL4GHI6MNO8TUV7PQRS9WXYZ0*#
1RADIO MEDIANAV ESC TRAFFIC
SETUPADDR
BOOK
2ABC3DEF5JKL4GHI6MNO8TUV7PQRS9WXYZ0*#
1RADIO MEDIANAV ESC TRAFFIC
SETUPADDR
BOOK

SELECTING A STATION


When the current radio station is
displayed on the screen, press OK.

The radio source short-cuts menu appears and provides access to
the following short-cuts:

Select the function required and
press OK to confi rm to gain access
to the corresponding settings.
TA


RDS, if displayed, allows you to continue listening to the same
station by automatic retuning to alternative frequencies. However,
in certain conditions, coverage of an RDS station may not be
assured throughout the country as radio stations do not cover
100 % of the territory. This explains the loss of reception of the
station during a journey.





The external environment (hill, building, tunnel, underground car park...)
may interfere with the reception, including in RDS following mode. This
phenomenon is a normal result of the way in which radio waves are
transmitted and does not in any way indicate a failure of the audio equipment.

RDS - REGIONAL MODE


Press the RADIO button to display the
list of stations received locally sorted
in alphabetical order.

Press one of the buttons on the numeric keypad for more than
2 seconds to store the current station. A bleep confi rms that
it has been stored.
Press the button on the numeric keypad to recall the stored radio
station.



RDS



Radiotext



Regional prog.


AM



RADIO


When the "RADIO" screen is displayed, turn the
ring or use the 4-direction navigator to select the
previous or next station on the list.
While listening to the radio, press buttons  and 
for the automatic search for a lower or higher
frequency. Select the station required by turning
the ring and press to confi rm.