key battery Peugeot RCZ 2015 Owner's Manual

4
RCZ_en_Chap00b_vue-ensemble_ed01-2015
ExTERIOR
Remote control key 37-40
- opening / closing
-

unlocking / partial opening of the boot
-


anti-theft protection
-

battery
Alarm
41-43
Boot
49
Temporary puncture repair kit

150-156
Changing a wheel


157-161
Active,

fixed spoiler 93-94,
95
Parking sensors

135-137
T

owbar 186-187
Towing

184-185
Changing bulbs


172-176
-


rear lamps
-


3rd stop lamp
-


number plate lamps Accessories

190-191
Cleaning, maintenance

188-189
Fuel tank


139-140Wipers

83-86
Changing a wiper blade

163
Door mirrors


55-56
Active bonnet


92
Lighting controls


75-80
Directional lighting


82
Headlamp height adjustment


81
Changing bulbs


169-172
-


front lamps
-


direction indicator repeaters
Doors

46-48
-

opening / closing
-


central locking
-


anti-intrusion security
-


emergency locking
Electric windows


44-45
Braking assistance


89
T

rajectory control
90-91
T

yre under-inflation detection 127-128
Tyre pressures

156, 198
Snow chains


162

39
RCZ_en_Chap02_ouvertures_ed01-2015
Folding the key
F First press this button to fold the key.
LOCATING YOUR VEHICLE
R

EMOTE
CONTROL
PROBLEM
Following disconnection of the vehicle battery, replacement of the
remote control battery or in the event of a remote control malfunction, \
you can no longer unlock, lock or locate your vehicle.
F
First of all, use the key in the lock to unlock or lock your vehicle.
F


Then, reinitialise the remote control.
If the problem persists, contact a PEUGEOT

dealer as soon as
possible.
Reinitialisation
F Switch of f the ignition.
F
T
urn the key to position 2 (Ignition on) .
F

Press the closed padlock immediately for a few seconds.
F


Switch of
f the ignition and remove the key from the ignition switch.
The remote control is fully operational again.
Changing the battery
Battery ref.: CR1620 / 3 volts.
If the battery is flat, you are informed by illumination of this
warning lamp, accompanied by an audible signal and an alert
message in the screen.
F


Unclip the casing using a coin at the notch.
F

Slide the flat battery out of its location.
F

Slide the new battery into its location observing the original
direction.
F


Clip the casing.
F


Reinitialise the remote control.
This function allows you to identify your vehicle from a
distance, particularly in poor light.

Your vehicle must be
locked.
F
Press the closed padlock on the remote control.
This will switch on the courtesy lamps and the direction indicators will\

flash

for

around

ten

seconds.
If you do not press the button when folding the key, there is a risk
of damage to the mechanism.
2/
ACCESS

45
RCZ_en_Chap02_ouvertures_ed01-2015
Reinitialisation
If a window does not rise automatically, after reconnecting the battery
for example, its operation must be reinitialised:
F
pull the switch until the window stops,
F


release the switch and pull it again until the window closes fully
,
F

continue to hold the switch for approximately one second after the
window has closed,
F


press the switch to lower the window automatically to the low
position,
F


when the window has reached the low position, press the switch
again for approximately one second.
The safety anti-pinch function is not operational during these
operations. Always remove the key from the ignition when leaving the vehicle,
even for a short time.
If an obstacle is encountered during operation of the electric
windows, you must reverse the movement of the window

. To do
this, press the switch concerned.
When the driver operates the switch for the passenger's electric
window, they must ensure that no one is preventing correct
closing of the windows.
The driver must ensure that the passengers use the electric
windows correctly.
Be aware of children when operating the windows.
2/
ACCESS

48
RCZ_en_Chap02_ouvertures_ed01-2015
Pressing the central locking control unlocks the vehicle.
Opening a door from the inside, when stationary, also unlocks the
vehicle, but the vehicle will be locked again when the speed exceeds
6 mph (10 km/h).
Activation / deactivation
You can activate or deactivate this function.
F
With the ignition on, press the button for more than two seconds.
A


confirmation message appears in the screen.
EMERGENCY LOCKING
To lock or unlock the doors mechanically in the event of a central
locking
system failure or flat battery.
Locking the driver's door
F Insert the key in the lock, then turn it to the right.
Unlocking the driver's door
F Insert the key in the lock, then turn it to the left.
Locking the passenger door
F Using the key, remove the black cap on the edge of the door.
F
Insert the key in the cavity without forcing, then without turning it,
move the the latch sideways towards the interior of the door

.
F Remove
the key and refit the cap.
Unlocking the passenger door
F Pull the interior door opening control.
ANTI-INTRUSION SECURITY
This function permits automatic and simultaneous locking of the doors,
boot lid and fuel filler flap as soon as the vehicle speed exceeds 6 mph
(10 km/h).
Operation
If one of the doors is open, the automatic central locking does not take\

place.
If the boot lid is open, the automatic central locking of the doors is
active.

11 6
RCZ_en_Chap06_conduite_ed01-2015
IGNITION SWITCH
Ignition on position
It allows the use of the vehicle's electric equipment or portable devices to be charged.
Once the state of charge of the battery drops to the reserve level, the \
system switches to energy economy mode: the power supply is cut off
automatically to preserve the remaining battery charge.
In wintry conditions, the warning lamp can stay on for a longer
period. When the engine is hot, the warning lamp does not
come
on.
STARTING-SWITCHING OFF THE ENGINE
It has 3 positions:
-
position 1 (Stop): insert and removing the key,
-
position 2 (Ignition on) : steering column unlocked, ignition on,
Diesel preheating, engine running,
-
position 3 (Starting).
STARTING THE ENGINE
With the parking brake applied and the gearbox in neutral or
position
N or P:
F

depress the clutch pedal fully (manual gearbox),


or
F press
the brake pedal firmly (automatic gearbox),
F

insert the key into the ignition switch; the system recognises
the

code,
F

unlock the steering column by simultaneously turning the steering
and the key

.
F

With a petrol engine, operate the starter motor by turning the key to
position 3

without pressing the accelerator pedal, until the engine
starts. Once the engine is running, release the key.
F

With a Diesel engine, turn the key to position 2

, ignition on, to
operate the engine pre-heating system.
In certain cases, you may have to apply more force to the steering
(wheels on full lock, for example).
Avoid attaching heavy objects to the key, which would weigh down
on its blade in the ignition switch and could cause a malfunction. Switching off the engine leads to a loss of braking assistance. Wait until this warning lamp goes off in the instrument panel
then operate the starter motor by turning the key to position
3
without pressing the accelerator pedal, until the engine starts.
Once the engine is running, release the key.