display Peugeot Rifter 2019 Owner's Guide

46
Accumulations (water, dust, grime, salt,
etc.) on the inner sur face of the door
handle may affect detection.
If cleaning the inner sur face of the door
handle using a cloth does not restore
detection, contact a
PEUGEOT dealer or
a


qualified workshop.
A sudden splash of water (stream of water,
high pressure jet washer, etc.) may be
identified by the system as the desire to
open the vehicle.
Central locking/unlocking
This function allows the doors to be locked
or unlocked simultaneously from inside the
vehicle. When locking/deadlocking from the
outside
When the vehicle is locked or deadlocked
from the outside, the red indicator lamp
flashes and the button is inactive.
F

A
fter normal locking, pull one of the
interior door handles to unlock the
vehicle.
F
A
fter deadlocking, it is necessary to
use the remote control,
K
eyless Entry
and Starting or the integral key to
unlock the vehicle.
Manual mode
F Press this button to lock /unlock the vehicle.
Driving with the doors locked could make
it difficult for the emergency ser vices to
enter the vehicle in an emergency.
If one of the doors is open, the central
locking from the inside does not function.
This is signalled by a


mechanical noise
from the locks.
If the boot is open, only the locking of the
other doors is carried out. The indicator
lamp in the button remains off. When locking from inside, the door mirrors
do not fold.
The indicator lamp also goes off when
unlocking one or more accesses.
Automatic mode
This is the automatic central locking of the
vehicle when driving, also called anti-intrusion
s e c u r i t y.
For more information on Anti-intrusion
security
, refer to the corresponding section.
Anti-intrusion security
This system allows automatic simultaneous
locking of the doors and tailgate as soon as the
speed of the vehicle exceeds 6
mph (10 km/h).
Operation
If one of the doors or the tailgate is open, the
automatic central locking does not take place.
This is signalled by the sound of the
locks rebounding, accompanied by
illumination of this warning lamp in the
instrument panel, an audible signal
and the display of an alert message.
Access

47
Activation/Deactivation
You can activate or deactivate this function
permanently.
F
W
ith the ignition on, press the central
locking button until an audible signal is
triggered and a
corresponding message of
confirmation is displayed.
The state of the system stays in the memory
when the ignition is switched off.
Driving with the doors locked may render
access by the emergency services to the
interior difficult in an emergency.
Carrying long or voluminous objects
If you want to drive with the boot open, you
should press the central locking button
to lock the doors. Other wise, every time
the speed of the vehicle exceeds 6
mph
(10
km/h), the locks will rebound and the
alerts mentioned above will appear.
Pressing the central locking button
unlocks the vehicle.
Above 6
mph (10 km/h), this unlocking is
te m p o r a r y.
Side-hinged doors
Keeping the left-hand door
closed with the right-hand door
open
Opening to approximately 180°
General
recommendations for the
sliding side doors
The doors must only be operated when
the vehicle is stationary.
For your safety and for that of your
passengers, as well as for correct
operation of the doors, you are strongly
advised not to drive with a
door open.
Always check that it is safe to operate
the door and, in particular, be sure not to
leave children or animals near the door
controls without supervision.
The audible warning, illumination of
the "door open" warning lamp and the
message in the multifunction screen are
there to remind you. Contact a
PEUGEOT
dealer or a
qualified workshop to
deactivate these warnings.
Lock your vehicle when using an
automatic car wash.
It is possible to drive with the right-hand
door open, to enable the transportation of
long loads.
The left-hand
door is kept closed by the
distinctive "yellow" lock, positioned at the
base of the door.
This closed door must not be used to
retain loads.
Driving with the right-hand door open is
a

special dispensation. Please comply
with the usual safety instructions on how
to warn other drivers. If fitted to your vehicle, a check strap system
allows the doors to be opened from about 90°
to about 180°.
F

P
ull the yellow control when the door is
open.
The check strap will engage again
automatically on closing.
2
Access

64
Rear box
It can be accessed from the rear seats and
from the vehicle's boot.
Its capacity is 60 litres, and the maximum
authorised load is 10
kg.
Open the rear box carefully to prevent any
objects stored inside from falling out.
Light ambience
The light ambience can be
configured from the vehicle's
configuration menu.
Blind
Opening/Closing
F
P
ress and hold the button; the blind opens/
closes and stops when you release the
button.
If the blind meets an obstacle during
operation, you must reverse its movement.
To do this, press the switch concerned.
When pressing the button to open/close
the blind, the driver must ensure that
nothing and no one might inter fere with its
movement.
The driver must ensure that passengers
use the blind correctly.
Be particularly aware of children when
operating the blind.
F

F

rom the rear seats, slide the boot shutters
to open it.
F

F

rom the vehicle's boot, place your thumb
on the boot recess then pull the handle to
open it.
12 V socket(s)
(Depending on version.)
F

T
o connect a 12 V accessory (maximum
power: 120
watts), lift the cover and plug in
the correct adapter.
Do not exceed the maximum power rating
of the socket (other wise there is a
risk of
damaging your portable device).
The connection of an electrical device
not approved by PEUGEOT, such as
a
USB charger, may adversely affect the
operation of vehicle electrical systems,
causing faults such as poor radio
reception or inter ference with displays in
the screens.
Ease of use and comfort

65
AC 220V
50Hz120W
USB socket(s)
(Depending on version.)
Sockets 1, 2
and 3 allow the connection of
a
portable device, such as an iPod
®-type digital
audio player, to recharge the device.
Sockets 1

and 2

also allow the audio files to
be read, which are transmitted to your audio
system and played via the vehicle's speakers.
You can manage these files using the steering
mounted or touch screen controls.
220 V/50 Hz socket
A 220 V/50 Hz socket (max. power: 120 W)
i s installed on the side of the central storage
compartment.
This socket works with the engine running, as
well as in STOP mode with Stop & Start. When the USB socket is used, the
portable device charges automatically.
A message is displayed if the power drawn
by the portable device exceeds the current
supplied by the vehicle.
For more information on how to use this
equipment, refer to the Audio equipment
and telematics
section.
The sockets 1 and 2 also allow
a smartphone to be connected
by MirrorLink
TM, Android Auto® or
CarPlay®, so that certain smartphone
applications can be used on the
touch screen. F

R
emove the cover.
F
C
heck that the indicator lamp is on and
green.
F
C
onnect your multimedia or other electrical
device (telephone charger, laptop computer,
CD-DVD player, bottle warmer, etc.).
In the event of a fault with the socket, the green
warning lamp flashes.
Have it checked by a PEUGEOT dealer or
a

qualified workshop.
Connect only one device at a time to the
socket (no extension lead or multi-socket
connector).
Connect only devices with class II
insulation (shown on the device).
Do not use a
device with a metal case
(electric shaver, etc.).
As a
safety measure, when electrical
consumption is high and when required by
the vehicle's electrical system (particular
weather conditions, electrical overload,
etc.), the current supply to the socket will
be cut off; the green indicator lamp goes
of f.
3
Ease of use and comfort

71
Air flow
If you place the air flow control to the
minimum position (system off), the
temperature in the vehicle will no longer
be controlled. A slight air flow can still be
felt however, resulting from the for ward
movement of the vehicle.
Temperature
Air distribution
Windscreen and side windows.
Central and side vents.
F

T

urn the thumbwheel 1 from "
LO" (cold) to
" HI " (hot) to adjust the temperature to your
requirements.
Footwells.
The air distribution can be adapted by
combining the corresponding buttons. F

T

urn the thumbwheel 2 to obtain
a

comfortable air flow.
Air conditioning
With the engine running, the air conditioning is
designed to operate effectively in all seasons,
with the windows closed.
It allows you:
-

i
n summer, to lower the temperature,
-

t
o increase the effectiveness of the
demisting in winter, above 3°C.
On/of f
F Press button 5 to activate/deactivate the air
conditioning system.
When the air conditioning is in operation, to
cool the air more quickly, you can use interior
air recirculation for a
few moments by pressing
button 4 . Then return to the intake of exterior
a i r.
The air conditioning does not operate
when the air flow adjustment is set to off.
Switching the system off may result in
some discomfort (humidity, misting).
Dual-zone automatic air
conditioning
1.Left-hand side/right-hand side
temperature.
2. A ir f low.
3. Air distribution.
4. Recirculation of interior air.
5. Air conditioning on/off.
6. Automatic comfort mode.
7. Visibility programme.
8. "Mono" function.
Automatic comfort mode
F Press the " AUTO" button 6 su c c e s s i ve l y.
The active mode appears in the display screen,
as described below:
Provides soft and quiet operation by
limiting air flow.
Offers the best compromise between
a
comfortable temperature and quiet
operation.
Provides dynamic and effective air
f low.
3
Ease of use and comfort

72
When the engine is cold, the air flow will
only reach its optimum level gradually
to prevent too much cold air being
distributed.
In cold weather, it favours the distribution
of warm air to the windscreen, the side
windows and the footwells only.
Manual mode
If you wish, you can make a different choice
f rom that offered by the system by changing
a
setting. The other functions will still be
automatically managed.
The " AUTO " symbol disappears if you change
a


setting.
Deactivating the system
F Press button 2 " -" until the fan symbol
disappears.
This action switches off all of the functions of
the system.
Temperature is no longer controlled. A slight air
flow can still be felt, however, resulting from the
for ward movement of the vehicle.
Temperature
The driver and front passenger can each set
the temperature to suit their requirements.
The value shown on the display is a
level
of comfort, not a
temperature in Celsius or
Fahrenheit.
F

P
ush button 1 down to decrease the value
or up to increase it.
A setting of around 21
provides optimum
comfort. Depending on your requirements,
a setting between 18
and 24 is normal.
In addition, it is recommended that you
avoid a
left /right setting difference of more
than 3.
On entering the vehicle, if the interior
temperature is much colder or warmer
than the comfort value setting, there is no
need to alter the value displayed in order
to reach the required level of comfort. The
system compensates automatically and
corrects the temperature difference as
quickly as possible.
F

P

ress button 2 " +" to switch the system on
again. For maximum cooling or heating of the
passenger compartment, it is possible
to exceed the minimum value 14
or the
maximum value 28.
F

P
ush button 1 down until "LO" is
displayed or up until " HI" is displayed.
F

P
ress corresponding button 8 to activate/
deactivate the function.
The indicator lamp in the button is on when the
function is activated.
The function is deactivated automatically if
a


passenger uses the temperature control.
Visibility programme
F Press "Visibility" button 7 to demist or
defrost the windscreen and side windows
more quickly.
" Mono " function
The comfort setting for the passenger's side
can be indexed to the driver's comfort setting
(mono-zone).
The system automatically manages the air
conditioning, air flow and air intake, and
provides optimum distribution towards the
windscreen and side windows.
Ease of use and comfort

76
12:13
23 °C
Additional heating/
ventilation
Heating
This is an additional and separate system
which heats the passenger compartment and
improves defrosting performance.
This indicator lamp is illuminated
when the system is programmed.
This indicator lamp flashes while
the heating is in operation or when
switched on remotely via the remote
control.
This indicator lamp goes off at the
end of the heating cycle or when the
heating is stopped using the remote
control.
Ventilation
This system allows ventilation of the passenger
compartment with exterior air to improve the
temperature experienced on entering the
vehicle in summer.
Programming
With Bluetooth® audio system
F Select " Pre-heat./Pre-ventil. ".
F
Sel
ect "Activation " and, if necessary for
programming, select " Parameters".
F

P
ress the MENU
button to
access the main menu.
F
Sel
ect "Heating " to heat the engine and
passenger compartment or " Ventilation" to
ventilate the passenger compartment.
F
Select:
-

t
he 1
st clock to programme/memorise
the time at which the pre-heating
temperature will be reached,
-

t

he 2
nd clock to programme/memorise
a

second time at which the pre-heating
temperature will be reached, Using these two clocks and depending on
the season you can, for example, select
one or the other start time.
A message in the screen confirms your
choice.
With PEUGEOT Connect Radio
Press
Connect-App or Applications
to display the primary page.
Then press " Programmable
heating/ventilation ".
F

Sel

ect the " Status" tab to activate/
deactivate the system.
Ease of use and comfort

83
F Turn the ring to another position.
Deactivation of the function is accompanied
by the display of a
message.
Operating fault
In the event of a fault with the
sunshine sensor, the lamps come on
and this warning lamp lights up in the
instrument panel, accompanied by an
audible signal and/or a message.
Contact a PEUGEOT dealer or a qualified
w orkshop.
In fog or snow, the sunshine sensor may
detect sufficient light. In this case, the
lighting will not come on automatically.
Do not cover the sunshine sensor, located
on the dashboard or at the top of the
windscreen behind the rear view mirror
(depending on equipment); the associated
functions would no longer be controlled.
Daytime running lamps/
sidelamps
The front lamps light up automatically when the
engine starts.
They provide the following functions:
-

D
aytime running lamps (lighting control
stalk at " AUTO" position with adequate light
level).
-

S
idelamps (lighting control stalk at " AUTO"
position with low light level or "Sidelamps
only" or "Dipped/main beam headlamps").
The LEDs are brighter when operating as
daytime running lamps.
Parking lamps
Automatic illumination of
headlamps
When a low level of ambient light is detected
b y a sunshine sensor, the number plate lamps,
sidelamps and dipped beam headlamps are
switched on automatically, without any action
on the part of the driver. They may also come
on if rain is detected, at the same time as
automatic operation of the windscreen wipers.
As soon as the brightness returns to
a
sufficient level or after the windscreen wipers
are switched off, the lamps are switched off
automatically.
F

T
urn the ring to the " AUTO" position.
Activation of the function is accompanied by
the display of a
message. Vehicle side marking by illumination of the
sidelamps on the traffic side only.
F

D
epending on version, within one minute
of switching off the ignition, operate the
lighting control stalk up or down, depending
on the traffic side (for example, when
parking on the right, push the lighting
control stalk downwards; the left-hand
sidelamps come on).
This is confirmed by an audible signal and
illumination of the corresponding direction
indicator lamp in the instrument panel.
To switch off the parking lamps, return the
lighting control stalk to the central position.
4
Lighting and visibility

90
Switching on
Give a short downwards push to the control
st alk.
A wiping cycle confirms that the instruction has
been accepted.
Depending on version, this symbol
appears in the display screen or
this indicator lamp comes on in the
instrument panel and a
message is
displayed.
Switching off
intensity of the rain without any action on the
part of the driver.
Give the control stalk another brief
p ush downwards or shift the control
stalk to a
different position (Int, 1 or 2).
This indicator lamp goes off in the
instrument panel and a
message is
displayed.
The automatic rain sensitive windscreen
wipers must be reactivated by pushing the
control stalk downwards, if the ignition has
been off for more than one minute.
Operating fault
If a fault occurs with the automatic windscreen
w ipers, the wipers will operate in intermittent
mode.
Have them checked by a
PEUGEOT dealer or
a


qualified workshop.
Do not cover the rain sensor, located at
the top of the windscreen behind the rear
view mirror (depending on equipment); the
associated functions would no longer be
controlled.
Switch off the automatic windscreen wipers
when using an automatic car wash.
In winter, it is advisable to wait until the
windscreen is completely clear of ice before
activating the automatic rain sensitive wipers.
Lighting and visibility

94
Electronic stability control
(ESC)
Electronic stability control programme
incorporating the following systems:
-
A
nti-lock braking system (ABS) and
Electronic brake force distribution (EBFD).
-
E

mergency braking assistance (EBA).
-
A

nti-slip regulation (ASR).
-
D

ynamic stability control (DSC).
-
A

utomatic post-collision braking (APCB).
-

T
railer stability assist (TSA).
Definitions
Anti-lock braking system (ABS)
and electronic brake force
distribution (EBFD)
These systems improve the stability and
manoeuvrability of your vehicle when braking
and contribute towards improved control in
corners, in particular on poor or slippery road
surfaces.
The ABS prevents wheel lock in the event of
emergency braking.
The EBFD system manages the braking
pressure wheel by wheel.
Emergency braking assistance
(EBA)
In an emergency, this system enables you to
reach the optimum braking pressure more
quickly and therefore reduce the stopping
distance.
It is triggered in relation to the speed at which
the brake pedal is pressed. This is felt by
a reduction in the resistance of the pedal and
an increase in braking efficiency.
Anti-slip regulation (ASR)
This system optimises traction in order to
avoid wheel slip by acting on the brakes of
the driving wheels and on the engine. It also
improves the directional stability of the vehicle
on acceleration.
Dynamic stability control (DSC)
If there is a difference between the path
f ollowed by the vehicle and that required by the
driver, this system monitors each wheel and
automatically acts on the brake of one or more
wheels and on the engine to return the vehicle
to the required path, within the limits of the laws
of physics.
Trailer stability assist (TSA)
This system allows control of the vehicle to be
retained when towing a trailer, so as to avoid
the risk of snaking.
Anti-lock braking system
(ABS) and electronic brake
force distribution (EBFD)
The fixed illumination of this warning
lamp signals that there is a fault with
the ABS.
Illumination of this warning lamp,
coupled with the STOP and ABS
warning lamps, accompanied by
the display of a
message and an
audible signal, signals that there is
a
fault with the electronic brake force
distribution (EBFD).
The vehicle retains conventional braking. Drive
carefully at moderate speed.
Contact a
PEUGEOT dealer or a qualified
workshop as soon as possible.
You must stop as soon as it is safe to do so.
Call a

PEUGEOT dealer or a qualified
workshop.
Safety