turn signal PONTIAC FIERO 1988 Service User Guide

385.10 STEERING WHEELS AND COLUMNS
Figure 8. Buzzer Switch Removal
1 16. SCREW. LOCK RETAINING I 19. LOCK CYLINDER SET, I STRG COLUMN I
Figure 9. Removing Lock Cylinder Set
9. Turn signal in "Right Turn" position
10. Screw (9) and crossover arm (10)
11. Turn signal lever
12. Screws (8)
13. Turn signal switch (1 1). Let switch hang freely if re-
moval is not necessary.
To remove:
A. Wire harness protector (33)
6. Gently pull wire harness through column
14. Key from lock cylinder set (1 9)
15. Buzzer switch (1 4) and clip (1 5)
16. Reinsert key
17. Lock retaining screw (1 6)
18. Lock cylinder set (1 9)
Install or Connect
(Figure 2,3,4,5,6,7,8,9,10)
1. Lock cylinder set (1 9) 2. Lock retaining screw (1 6)
3. Key in "Run" position
4. Clip
(1 5) and buzzer switch (1 4)
5. Turn signal switch (1 1)
6. Screws (8)
7. Crossover arm (10) lubricated with lithium grease and
screw (9)
8. Upper bearing spring
(7) 9. Turn signal cancelling cam (6)
10. Shaft lock (5) 11. Shaft lock retaining ring (4) using J 23653-A to depress
shaft lock (5) 12. Cover (3) 13. Steering wheel
Figure 10. Wire Harness Through Column
14. Jam nut (2) and retainer (1)
15. Turn signal lever
16. Wire harness protector (33)
17. Horn pad and screws to back of steering wheel
SUB SECTION B
INCLUDES: DIMMER SWITCH, IGNITION SWITCH, LOCK
HOUSING, COVER SHROUD, KEY RELEASE LEVER,
SWITCH ACTUATOR RACK, SWITCH ACTUATOR SEG-
MENT, LOCK BOLT, PIVOT AND SWITCH ASSEMBLY,
AND UPPER BEARING
Tools Required:
J 23653-A Lock Plate Compressor J 1859-03 Steering Wheel Puller
++ Remove or Disconnect
(Figure 2 thru 15)
1. Perform steps 1 thru 18, Remove or Disconnect, Sub
Section A
(12) 12 O'CLOCK
12. SCREW, PAN HD
&LOBED SOC TAP
Figure 11. Lock Housing Cover Screw Positions
2. Thrust washer (1 3) 3. Screws (1 2)
4. Mounting bolt (35)
5. Hex nut (42)
6. Dimmer switch (41)
7. Dimmer switch rod (40)
8. Mounting stud (34)
9. Ignition switch (36)

385.1 2 STEERING WHEELS AND COLUMNS
11. Shroud (38) to lock housing cover (1 7) 2. Steering column
from car
12. Screws (39) 3. Lower bearing adapter
clip (47)
13.
Lock housing cover (17) and shroud (38) assembly to 4. Retainer, bearing adapter (46)
column 5. Bearing ASM (45
14. Screws (1 2) 7. Cover (3) d 6. Lower bearing a apter (44)
8.
Shaft lock retaining ring (4) using J 23653-A to depress
shaft lock (5)
9. Shaft lock (5), turn signal cancelling cam (6), and upper
bearing spring (7)
10.
Shaft (49)
Install or Connect
(Figure 2,3,4,5,19) UNTIL DRILL HITS T
SURFACE OF HOUSING
1. Shaft (49)
2. Upper bearing spring (7)
3. Turn signal cancelling cam (6)
4. Shaft lock (5) 5. Shaft lock retaining ring (4) using J 23653-A to depress
shaft lock (5) Figure 18. Adjust Dimmer Switch 6. Cover (3)
16.
Dimmer switch rod (40) 7. Lower bearing adapter 44)
17.
Dimmer switch (41) and hex nut (42). Adjust dimmer 8. Lower bearing ASM (45
switch 9. Lower bearing adapter retainer (46)
18.
Thrust washer (1 3) 10. Clip (47)
19. Perform
steps 1 thru 17, Install or Connect, Sub 11. Steering column to car
Section
A 12. Perform steps 13 thru 17, Install
or Connect, Sub
Section A
SUB SECTION C
INCLUDES: SHAm AND LOWER BEARING ASSEMBLY
Tools Required:
J 23653-A Lock Plate Compressor J 1859-03 Steering Wheel Puller
++ Remove or Disconnect
(Figures 2,3,4,5,19)
1. Perform steps 1 thru 4, Remove or Disconnect, Sub
Section A
43 JACKET ASM
44 ADAPTER, LOWER BEARING
45 BEARING ASM
1 46 RETAINER, BEARING ADAPTER I ( 47 CLIP, LOWER BEARING
ADAPTER I
1 48 RING, RETAINING I 1 49 SHAFTASM I C I
Figure 19. Lower Bearing Assembly

SAGINAW STEERING GEAR DIVISION
GENERAL MOTORS CORPORATION
Key No. Part Name
1 - RETAINER
2
- NUT, HEXAGON JAM
3
- COVER, SHAFT LOCK
4
- RING, RETAINING
5
- LOCK, STEERING SHAFT
6
- CAM ASM, TURN SIGNAL CANCELLING
7
- SPRING, UPPER BEARING
8
- SCREW, BINDING HEAD CROSS RECESS
9 - SCREW, ROUND WASHER HEAD
10
- ARM ASM, SWlTCH ACTUATOR
11
- SWITCH ASM, TURN SIGNAL
12
- SCREW, HEX WASHER HEAD TAPPING
13
- WASHER, THRUST
14
- SWITCH ASM, BUZZER
15
- CLIP, BUZZER SWITCH RETAINING
16
- SCREW, LOCK RETAINING
17
- HOUSING, STEERING COLUMN
18
- SECTOR, SWITCH ACTUATOR
19 -LOCK CYLINDER SET, STEERING COLUMN
20
- BEARING ASM
21
- BUSHING, BEARING RETAINING
22
- RETAINER, UPPER BEARING
23
- SWITCH ASM, PIVOT &
24 - BOLT, LOCK
25
- SPRING, RACK PRELOAD
26
- RACK. SWlTCH ACTUATOR
27 - ROD, SWITCH ACTUATOR
28
- WASHER. SPRING THRUST
29 - PIN, SWITCH ACTUATOR PIVOT
30
- PROTECTOR, WIRING
Key No. Part Name ASSEMBLIES
31 - BOWL, FLOOR SHIFT
0 - COLUMN ASM, E/A STEERING
32
- SCREW, BINDING HD CROSS RECESS
101 - BOLT ASM, SPRING &
33 - ROD, DIMMER SWITCH ACTUATOR
102 - BOWL ASM. GEARSHIFT LEVER
34
- SWITCH ASM, DIMMER
103 - JACKET ASM, STEERING COLUMN
35
- NUT, HEXAGON 104 - SWITCH ASM, COLUMN LOCK & IGN
36 - JACKET ASM, STEERING COLUMN
37
- ADAPTER, LOWER BEARING SERVlCE KITS
38 - BEARING ASM 201 - HOUSING ASM SERVICE KIT
39
- RETAINER, BEARING ADAPTER STEERING
COLUMN
40
- CLIP. LOWER BEARING ADAPTER 202 - SECTOR SERVICE
KIT, IGNITION
41
- RING. RETAINING SWITCH
ACTUATOR
42
- SHAFT ASM, STEERING 203 - SHAFT
REPAIR KIT INJ. STEERING
43
- HOUSING ASM, IGN SWITCH
44
- SCREW. WSHER HEAD
45
- SCREW, PAN HD
46
- STUD, DlMR & IGN SW MOUNTING
47
- SWITCH ASM, IGNITION
48 - BRACKET ASM. STRG. COL. SUPPORT

SUB SECTION A
INCLUDES: SHAFT LOCK, TURN SIGNAL CANCELLING
CAM, UPPER BEARING SPRING, SHAFT ASSEMBLY,
AND LOWER BEARING ASSEMBLY
Tools Required:
J 23653-A Lock Plate Compressor J 1859-03 Steering Wheel Puller
Remove or Disconnect
(Figures
2,3,4,5,6)
NOTICE: Wheels of car must be straight ahead. Failure to
do so may cause improper alignment of some components
during installation, resulting in
colunin malfunction.
Key in "Lock" position. Failure to do so
wi!l cause steering
wheel to turn, (see above).
CAUTION: Disconnect battery. Failure to do so may
cause electrical shock when working with wiring.
HORN
C
STEERING WHEEL
HORN PAD
I
C SCREWS
1 RETAINER
2 NUT, HEXAGON
A STEERING WHEEL
B VELCRO
FASTENEF v C HORNASM
1 RETAINER
2 NUTSHEXAGON
Figure 2. Removing Horn Pad, Retainer, and Jam Nut
Figure
3. Removing Steering Wheel
1. Horn pad and electrical connectors
2. Retainer (1) and jam nut (2)
3. Steering wheel using J 1859-03 4. Column from car if removingirepairing shaft assembly
(42) or lower bearing assembly (37-40)
5. Shaft lock retaining ring (4) using
J 23653-A to depress
shaft lock (5)
6. Shaft lock (5) and cover (3)
7. Turn signal cancelling cam (6)
STEERING WHEELS AND COLUMNS 385-15
I
4. RING, RETAINING 5. LOCK. SHAFT
Figure 4. Removing Shaft Lock Retainingain;
SY. TURN SIG CANCELLING , UPPER BEARING
Figure 5. Removing Components from Upper Shaft
36 JACKET ASM
40 CLIP, LOWER BEARING
37 ADAPTER, LOWER BEARING ADAPTER
38 BEARING
ASM 41
RING, RETAINING 42 SHAFT ASM
Figure 6. Lower Bearing Assembly and Shaft Removal
Upper bearing spring
(7) Shaft (42)
Clip, lower bearing adapter (40)
Retainer, bearing adapter
(39) Bearing ASM (38) Adapter, lower bearing (37)
Install or Connect
(Figures
2 thru 6)
NOTICE: Ensure all fasteners are securely seated before
applying required torque. Failure to do so may result in
component damage or malfunctioning of steering column.
1. Adapter, lower bearing (37) 2. Bearing ASM (38)
3. Retainer, bearing adapter (39)
4. Clip, lower bearing adapter (40)

385-16 STEERING WHEELS AND COLUMNS
5. Shaft assembly (42) to column 6. Bearing spring (7)
7. Turn signal cancelling cam (6)
8. Shaft lock (5) and cover (3) 9. Shaft lock retaining ring (4) using J 23653-A to depress
shaft lock (5) 10. Column to dash 1 1. Steering wheel 12. Jam nut (2) 13. Retainer (1) 14. Horn pad
SUB SECTION Ej
INCLUDES: DIMMER SWITCH, IGNITION SWITCH, AND
DIMMER SWITCH ROD
Remove or Disconnect
(Figures
7,8)
1. Hex nut (35)
2. Mounting bolt (44)
3. Dimmer switch (34) 4. Dimmer switch rod (33)
5. Mounting stud (46)
6. lgnition switch (47)
Figure 7. Dimmer Switch Assembly
IGN SW MOUNTING
Figure 8. lgnition Switch Assembly install
or Connect
(Figures
7,8,9,10)
NOTICE: Ensure all fasteners are securely seated before
applying required torque. Failure to do so may result in
component damage or malfunctioning of steering column.
1. Key in "Lock" posit~sn 2. lgnltion switch (47)
3. Mounting stud (46)
4. Dimmer switch rod (33)
5. Dimmer switch (34), adjust 6. Hex nut (35) 7. Mounting bolt (44)
47 SWITCH ASM. IGN 8
Figure 9. Adjusting Ignition Switch
UNTIL DRILL HITS TOP
SURFACE OF HOUSING
34 SWITCH. DIMMER I
Figure 10. Adjusting Dimmer Switch

STEERING WHEELS AND COLUMNS 385-17
SUB SECTION C
INCLUDES: TURN SIGNAL SWITCH, BUZER SWITCH,
AND CYLINDER LOCK SET
Tools Required:
J 23653-A Lock Plate Compressor J 1859-03 Steering Wheel Puller
Remove or Disconnect
(Figures
2,3,4,5,6,7,8,9,10,11,12,13)
1. Perform ste~s 1 thru 8, Remove or Disconnect, Sub
Section A
, STEERING COLUMN
Figure 13. Lock Cylinder Set and
Buzzer Switch Removal
Figure 11. Turn Signal Switch Removal Preparation
Figure 14. Wire Harnesses Through Column
Install or Connect
(Figures
2 thru 14)
NOTICE: Ensure all fasteners are securely seated before
applying required torque. Failure to do so may result In
component damage or malfunctioning of steering column.
1. Lock cylinder set (1 9)
2. Key in "Run" position 3. Lock retaining bolt (16) 4. Clip (15) and buzzer switch (14)
5. Turn signal switch (1 1) 6. Screws (8) 7. Signal switch arm (1 0) and screw (9) 8. Hazard knob 9. Perform steps 4 thru 15, Install or Connect,
Figure 12. Turn Signal Switch Removal Sub
Section A
SUB SECTION D I 2. Turn signal in "Right Turn" position 3. Hazard knob
4. Screw (9) and signal switch arm (10) 5. Screws (8)
6. Turn signal switch (1 1). Let switch hang freely if
removal-is not necessary.
To remove:
A. Clip and wire harness protector (30) B. Gently pull wire harness through column 7.. Key from lock cylinder (19)
8. Buzzer switkh (14) and clip (1 5) 9. Lock retaining bolt (1 6)
10. Reinsert key in lock cylinder (19) 1 1. Lock cylinder set (19)
INCLUDES: LOCK HOUSING COVER, SHROUD, UPPER
BEARING, ACTUATOR RODIRACK ASSEMBLY, LOCK
BOLT, AND PIVOT AND SWITCH ASSEMBLY
Tools Required:
J 23653-A Lock Plate Compressor J 1859-03 Steering Wheel Puller
Remove or Disconnect
(Figures 2 thru 16)
1. Perform stem 1 thru 8, Remove or Disconnect, Sub
Section A ' 2. Perform steps 1 thru 6, Remove or Disconnect, Sub
Section B

GENERAL MOTORS CORPORATION
1 - RETAINER
35 - ACTUATOR ASM, IGNITION SWITCH 69 - JACKET ASM, STEERING COLUMN
2 - NUT, HEXAGON JAM
36 - RACK, SWITCH ACTUATOR 70 - ADAF"TER, LOWER BEARING
3 - COVER, SHAn LOCK 37 - SPRING, RACK PRELOAD 71 - BEARING ASM
4
- RING, RETAINING 38 - HOUSING, STEERING COLUMN 72 - RETAINER, BEAR1NG ADAPTER
5 - LOCK, SHAn 39 - SECTOR, SWITCH ACTUATOR
73 - CLIP, LOWER BEARING ADAPTER
6
- CAM ASM, TURN SIGNAL CANCELLING 40 - SCREW, HEX WASHER HEAD 74 - LEVER ASM, T/S MULTlFUNCTBON
7 - SPRING, UPPER
BEARING
41 - GUIDE, SPRING 75 - LEVER ASM, TILT RELEASE
8
- SCREW, BINDING HEAD CROSS RECESS 42 - SPRING, WHEEL TILT 76 - KNOB, HAZARD WARNING SWlTCH
9 - SCREW, ROUND WASHER MEAD
43 - RETAINER, SPRING 77 - SPRING, HAZARD WARNING
10 - ARM ASM, SIGNAL SWITCH 44 - CAP, COLUMN HOUSING COVER END 78 - BUTBON, HAZARD WARNING
11 - SWITCH
ASM, TURN SIGNAL 45 - PIN, SWITCH ACTUATOR PIVOT 79 - SCREW, OVAL HEAD
12
- SEAT, UPPER BEARING INNER RACE 46 - SWITCH ASM, PIVOT &
13 - RACE, INNER 47 - SPRING, PIN PRELOAD
14
- SCREW, PAN HEAD CROSS RECESS 48 - SWITCH ASM, IGNITION
15 - SWITCH
ASM, BUZZER 49 - STUD, DlMMER & IGNITION SWITCH ASSEMBLIES
16 - CLIP, BUZZER SWITCH RETAINING MOUNTlNG
17 - SCREW,
LOCK RETAINING 50 - SCREW, WASHER HEAD 0 - COLUMN
ASM, EiA STEERING
18
- COVER, LOCK HOUSING 51 - PLATE, SHROUD RETAINING 101 - COVER ASM, LOCK HOUSING
19 - LOCK CYLINDER SET, STEERING COLUMN 52 - SCREW,
OVAL HEAD GROSS RECESS 102 - HOUSING
ASM, STEERlNG COLUMN
20
- ACTUATOR, DIMMER SWITCH ROD 53 - PIN, DOWEL 103 - SHAFT
ASM, STEERING
21 -THIS NUMBER NOT USED 54 - PROTECTOR, WIRING
104 - SUPPORT
ASM, STEERING COLUMN
22
- BEARING ASM 55 - SHAFT
ASM, RACE & UPPER HOUSING
23
- BOLT, LOCK 56 - SPHERE,
CENTERING
24
- SPRING, LOCK BOLT 57 - SPRING, JOINT PRELOAD
25
- SHOE, STEERING WHEEL LOCK 58 - SHAFT ASM, LOWER STEERING
26 - SHOE, STEERING WHEEL LOCK 59 - SCREW,
SUPPORT
27
- SHAFT, DRIVE 60 - SUPPORT, STEERlNG COLUMN HOUSING
28
- PIN, DOWEL 61 - PLATE,
LOCK
29
- PIN, PIVOT 62 - FINGER PAD, RELEASE LEVER
30
- SPRING, SHOE 63 - LEVER, KEY RELEASE
31
- SPRING, RELEASE LEVER 64 - SPRING,
KEY RELEASE
32 - PIN, RELEASE LEVER 65 - SHROUD, STEERING COLUMN HOUSING
33
- LEVER, SHOE RELEASE 66 - ROD, DIMMER SWlTCH
34 - BEARING ASM 67 - SWITCH ASM, DlMrVlER
68 - NUT,
HEXAGON

STEERING WHEELS AND COLUMNS 385-21
SUB SECTION A
INCLUDES: SHAR LOCK, TURN SIGNAL CANCELLING
CAM, UPPER BEARING SPRING, UPPER BEARING
SEAT, INNER RACE TURN SIGNAL SWITCH,
BUZER SWITCH, AND LOCK CYLINDER SET
Tools
Requird: J 236534 Lock Plate Compressor J 35689-A Terminal Remover
Remove or Disconnect
(Flgure 2,3,4,5,5,7,8,9)
NOTICE: Wheels of car must be straight ahead. Failure to
do so may cause improper alignment of some components
' during installation, resulting in column malfunction.
Key in "Lock" position. Failure to do so will cause steering
wheel
to turn, (see above).
CAUTION: Disconnect battery. Failure to do so may cauee electrical shock when working with wiring.
A STEERING WHEEL B HORN PAD
C SCREWS
1 RETAINER
2 NUT, HEXAGON
B VELCRO FASTENER C HORNASM
1 RETAINER
Figure 2. Removing Horn Pad, Retainer, and Jam Nut
Figure 3. Remove
Stwring Wheel
1. Worn pad and electrical connectors 2. Retainer (1) and jam nut (2) 3. Steering wheel using J 1859-03 4. Shaft lock retaining ring (4) using J 23653-A to depress
shaft lock (5) 5. Shaft lock (5) and shaft lock cover (3) 6. Turn signal cancelling cam (6) 7. Upper bearing sprin (7) 8. Upper bearing seat 71 2)
9. inner race (1 3)
Figure 4. Removing Shafl hock Retaining Ring
3. COVER, SHAFT LOCK 5. LOCK, SHAFT 6. CAM ASM, TURN SIG CANCELLING 7. SPRING, UPPER BEARING 12. SEAT, UPPER BEARING INNER RACE 13. RACE, INNER
Figure 5. Removing Components from Upper Shafl
ROSSRECESS
Figure 6. Turn Signal Swltch Removal Preparation
Figure
7. Turn Signal Switch Removal

385-22 STEERING WHEELS AND COLUMNS
10. Turn si nal to "Right Turnn position 11. Screw f9) and signal switch arm (10) 12. crews (8) 13. Turn signal switch (11). Allow switch to hang freely if re- moval is not necessary.
To remove:
A. Wiring protector (54) B. Hanard knob C.Gently pull wire harness through column housing
shroud (65), column housing (38), and lock housing
cover (1 8)
5. Turn signal switch (I 1) wire harness through lock hous-
ing cover (18), column housing (38), and column hous-
ing shroud (65)
6. Turn signal switch (1 1) and screws (9) and torque to
2.8-4.0
N.m (24.78-35.4 Lbs.ln.) 7. Signal switch arm (10) and screw (9) and torque to 1.7- 2.8 N.m (1 5.05-24.78 Lbs. In.)
8. Inner race (13)
9. Upper bearing seat (12)
10. Upper bearing spring (7)
11. Turn signal cancelling cam (6)
12. Shaft lock (5)
13. Shaft lock retaining ring (4) using J 23653-A to depress
shaft lock (5)
14. Steering wheel
15. Jam nut (2) and retainer
(1) 16. Screws to back of steering wheel, horn pad
17. Wiring protector (54)
SUB SECTION 6
17. SCREW, LOCK RETAINING INCLUDES:
LOCK HOUSING COVER, COVER END CAP, 19. LOCK CYLINDER SET, STRG COLUMN PIVOT
AND SWITCH ASSEMBLY, DIMMER SWITCH
ROD ACTUATOR, AND TILT SPRING ASSEMBLY
Flgurs 9. Rsmovlng Lock Cylinder Set Tools
Required:
J 23653-A Lock Plate Compressor
J 35689-A Terminal Remover
14. Key from lock cylinder set (19)
15.
Buuer switch (1 5) and clip (1 6)
16. Reinsert key in lock cylinder set (1 9) Remove
or Disconnect
17. Key in "Lock" position
m(Flgure 2,3,4,5,6,7,8,9,10,11,12,13,14) -
18. Lock retaining screw (1 7) 19. Lock cylinder set (1 9) 1. Perform steps 1 thru 19, Remove or Disconnect, Sub
Section A
lnsbll or Connect 2.
Screws (14)
m~(FIguns 2,3,4,56,7,(1,9,10) 3. Lock housing cover (1 8)
4. Tilt release lever (75)
5. Housing cover end cap
(44), and dimmer switch rod
NOTICE: Ensure all fasteners are securely seated before actuator (20)
applying required torque. Failure to do so may result in
component damage or malfunctioning of steering column.
lmporlant
Cruise control equipped columns: Unplug cruise
1. Lock cylinder set
(1 9) control
connector and remove multifunction lever 2. Lock retainin screw (17) and torque to 2.0-3.0 N-m (74).
(1 7.7-2~55 ~!s.ln.) 3. Key in "Runn position 4. Buner switch (1 5) and clip (1 6)

NAW STEER NG GEAR
GENERAL MOTORS CORBOR
1 - RETAINER
35 - ACTUATOR ASM, IGNlTlON SWITCH
2
- NUT, HEXAGON JAM 36 - RACK, SWITCH ACTUATOR
3
- COVER, SHAFT LOCK
37 - SPRING, RACK PRELOAD
4
- RING, RETAINING 38 - HOUSING, STEERING COLUMN
5
- LOCK, SHAFT
39 - SECTOR, SWITCH ACTUATOR
6
- CAM ASM, TURN SIGNAL CANCELLING 40 - SCREW, HEX WASHER HEAD
7
- SPRING, UPPER BEARING
41 - GUIDE, SPRING
8 - SCREW, BINDING HEAD CROSS RECESS 42 - SPRING, WHEEL TILT
9 - SCREW, ROUND WASHER HEAD
43 - RETAINER, SPRING
10
- ARM ASM, SIGNAL SWITCH 44 - CAP, COLUMN HOUSING COVER END
11 - SWlTCH ASM, TURN SIGNAL 45 - PIN, SWlTCH ACTUATOR PIVOT
12 - SEAT, UPPER BEARING INNER RACE
46 - SWITCH ASM, PIVOT &
13 - RACE, INNER 47 - SPRING, PIN PRELOAD
14
- SCREW, PAN HEAD CROSS RECESS 48 - MOUSING,
IGN SWITCH INHIBITOR
15 - SWITCH ASM, BUZZER 49 - SCREVV, VVASHER MEAD
16
- CLIP, BUZZER SWITCH RETAINING 50 - SWITCH, IGNITION
17 - SCREW,
LOCK RETAINING 51 - SWITCH, PIVOT & PULSE
18
- COVER, LOCK HOUSING 52 - SCREW,
OVAL HEAD CROSS RECESS
19
- LOCK CYLINDER SET, STEERING COLUMN 53 - PIN, DOWEL
20
- ACTUATOR, DIMMER SWITCH ROD 54 - PROTECTOR, WlRlNG
21 -THIS
NUMBER NOT USED 55 - SHAFT
ASM, RACE & UPPER
22
- BEARING ASM 56 - SPHERE,
CENTERING
23
- BOLT, LOCK 57 - SPRING,
JOINT PRELOAD
24
- SPRING, LOCK BOLT 58 - SHAFT ASM, LOWER STEERING
25
- SHOE, STEERING WHEEL LOCK 59 - SCREW,
SUPPORT
1 26 - SHOE, STEERING WHEEL LOCK 60 - SUPPORT,
STEERING COLUMN HOUSING
27
- SHAR, DRIVE 61 - PLATE, LOCK
28
- PIN, DOWEL 62 - SHROUD,
STEERING COLUMN HOUSING
29
- PIN, PIVOT 63 - ROD,
DIMMER SWITCH
30
- SPRING, SHOE 64 - SWITCH
ASM, DIMMER
31
- SPRING, RELEASE LEVER 65 - NUT,
HEXAGON
32
- PIN, RELEASE LEVER 66 - JACKET
ASM, STEERING COLUMN
33
- LEVER, SHOE RELEASE 67 - ADAPTER, LOWER BEARING
34
- BEARING ASM 68 - BEARING
ASM 69
- RETAINER,
BEARlNG ADAPTER
70
- CLIP, LOWER BEARING ADAPTER
ASSEMBLIES
0 - COLUMN ASM, E/A STEERING
101 - COVER ASM, LOCK HOUSlNG
102
- HOUSING ASM, STEERlNG COLUMN
103
- SHAFT ASM, STEERING
104 - SUPPORT ASM, STEERlNG COLUMN
HOUSlNG