ABS PORSCHE 911 TURBO 2014 6.G User Guide

182 Driving and Driving Safety
Combined operation of PSM and PTV Plus
In order to ensure optimum stabilization of the vehicle, the center differential lock is influenced when PSM interventions occur on vehicles with PTV Plus.
Combined operation of PSM and PTM
In order to ensure optimum stabilization of the vehicle, torque distribution between the front and rear wheels is adapted and the differential lock is influenced when PSM interventions occur on vehicles with PTV Plus.
In the event of a PTM fault, PSM cannot be switched off.If PSM is switched off, it is switched on again automatically.
Automatic brake differential (ABD)
The ABD system controls the front and rear axles separately. If one wheel of an axle starts to spin, it is braked so that the other wheel on the same axle can be driven.
ABD recognizes different driving states, and it features control strategies adapted to these states. In situations in which little propulsive power is required, such as when the vehicle moves off on a level gravel surface, traction control already becomes active at low engine speeds. If a large amount of propulsive power is required, e.g. when driving off on an uphill slope or for rapid acceleration, the ABD system is adapted accordingly.
Anti-slip control (ASR)
The anti-slip control system prevents the wheels from spinning by adjusting the engine power, thereby ensuring good lane-holding ability and stable handling.
Engine drag torque control (MSR)
In conditions of excessive slip, the engine drag torque control system prevents all driven wheels from locking up when the vehicle is overrunning. This is also the case for downshifts on a slippery road.
Steering torque pulse
The steering torque pulse provides the driver with steering assistance when braking on road surfaces with differing friction values.Additional steering forces also assist the driver during counter steering.
Switching off PSM
fPress button for at least 1 second.PSM is switched off after a short delay.The indicator light on the button and the PSM OFF warning light on the instrument panel light up.The warning “ PSM off” appears on the multi-function display in the instrument panel.
When you brake in the ABS control range , the vehicle is stabilized even when PSM is switched off.
One-sided spinning of the wheels is prevented, even with PSM switched off.
14_991_Turbo_21.book Seite 182 Mittwoch, 9. April 2014 2:19 14

Driving and Driving Safety 183
When PSM is switched off, PSM support is no longer provided in critical driving situations outside the ABS control range. fPSM should always be switched on during “normal” driving.
However, it may be a good idea to switch off PSM temporarily in exceptional situations:– On a loose surface and in deep snow.– When “rocking the vehicle free”.
Information
The vehicle retains its enhanced braking readiness through prefilling of the brake system even when PSM is switched off.
When PSM is switched off, wheel-specific brake interventions and the anti-slip control system (ASR) are also switched off.The automatic brake differential (ABD) remains on.
Switching PSM back on
fPress button . PSM is active immediately.The indicator light on the button and the PSM OFF warning light on the instrument panel go out.The message “ PSM on” appears on the multi-function display in the instrument panel.
“Sport Plus” mode
A sportier setup is obtained when “ Sport Plus” mode is switched on.PSM interventions occur later than in Normal mode. The vehicle can be maneuvered with greater agility at its performance limits, without having to dispense with the assistance of PSM in emergency situations. This helps to achieve optimal lap times, particularly on race circuits and on a dry road surface.
PSM warning light
– The PSM warning light on the instrument panel lights up for a lamp check when the ignition is switched on.– The light indicates a control operation, even when PSM is switched off, e.g. brake control in the event of one-sided wheel spin.– The light – in conjunction with the multi-function display – indicates a fault.The warning message “ PSM failure Consult a workshop Adapted driving permitted ” appears on the multi-function display in the instrument panel.
For information on warning messages on the multi-function display:fPlease see the chapter “OVERVIEW OF WARNING AND INFORMATION MESSAGES” on page 129.fAdapt your driving style according to the changed conditions.fContact an authorized Porsche dealer.
Towing
For information on towing:fPlease see the chapter “TOWING” on page 278.
No PSM assistanceWARNINGh
14_991_Turbo_21.book Seite 183 Mittwoch, 9. April 2014 2:19 14

184 Driving and Driving Safety
HOLD function: Drive-Off
Assistant, Standstill Management
The HOLD function, as an assistance function, assists the driver when stopping and driving off on upward slopes.The vehicle is automatically prevented from rolling back away from the desired direction of travel.When the HOLD function is active, the indicator light on the instrument panel comes on.
The vehicle is stopped and prevented from rolling back away from the desired direction of travel even without pressing the brake.
Information
The HOLD function is not available if the PDK selector lever is in position P and N.
If the PDK selector lever is moved while the HOLD function is active, the HOLD function is deactivated.
If the driver’s safety belt is unfastened and the driver’s door is opened while the HOLD function is active, the electric parking brake is activated automatically.
For information on the electric parking brake:fPlease see the chapter “ELECTRIC PARKING BRAKE” on page 151.
The limits set by the physics of driving cannot be overcome, even with the HOLD function. Responsibility for driving off on upward slopes is still the driver’s, despite the HOLD function.Assistance by the HOLD function is not always guaranteed when stopping and driving off on a slippery surface (e.g. on icy or loose surfaces). In this case, the vehicle can slip.fAlways adjust your driving style to the driving conditions and vehicle load. Use the footbrake if necessary.
If the Drive-Off Assistant is not functioning, the driver cannot be assisted when driving off on hills.fHold the vehicle with the footbrake.
If the vehicle comes to a standstill on a steep uphill gradient without operation of the footbrake by the driver, this may result in a certain roll-back before the vehicle is held by the HOLD function. In this situation, the roll-back can be reduced by pressing the footbrake.fAssist holding of the vehicle by increasing the braking force with the footbrake.
Information
When the HOLD function is active, the brake pedal may feel different and you may hear hydraulic noises.
This behavior is normal for the system. It is not a fault.
ABS Brake System
(Anti-lock Brake System)
In spite of the advantages of ABS, it is still the driver’s responsibility to adapt his driving style and maneuvers in line with road and weather conditions, as well as the traffic situation.
The increased safety that is provided should not induce you to take greater risks with your safety. The limits set by the physics of driving cannot be overcome, even with ABS.Risk of accidents due to inappropriate speed cannot be reduced by ABS.
ABS helps provide:
– Full steering control The vehicle remains steerable– Good driving stability No skidding due to locked wheels– Optimum braking distance Shorter stopping distance in most cases– Prevention of wheel locking No flat spots on the tires
Limits of HOLD Function
Drive-Off Assistant Not Working
Vehicle Roll-back
WARNINGh
CAUTIONh
CAUTIONh
Loss of control over the vehicleWARNINGh
14_991_Turbo_21.book Seite 184 Mittwoch, 9. April 2014 2:19 14

Driving and Driving Safety 185
Function
The decisive advantage of ABS lies in the driving stability and maneuverability of the vehicle in hazardous situations.
ABS prevents locking of the wheels during full braking, on almost all road surfaces, until just before the vehicle stops.
ABS begins to control the braking process as soon as a wheel shows a tendency to lock.This controlled braking process is comparable with extremely rapid cadence braking.The pulsating brake pedal and a “juddering noise” warn the driver to adapt his driving speed to the road conditions.fIf full braking is necessary, press the brake pedal fully during the whole braking operation, even though the pedal is pulsating. Do not reduce brake pressure.
Warning light USA
Warning light Canada
If the ABS warning light lights up on the instrument panel while the engine is running, the ABS has switched off because of a fault.The warning message “ ABS/PSM failure Adapted driving permitted ” appears on the multi-function display in the instrument panel.
For information on warning messages on the multi- function display: fPlease see the chapter “OVERVIEW OF WARNING AND INFORMATION MESSAGES” on page 129.
In this case, the braking system will operate without lock prevention , as in vehicles without ABS.fAdapt your driving style to the changed braking behavior.The ABS must be checked by your authorized Porsche dealer in order to prevent the occurrence of further faults with unpredictable consequences.Please contact an authorized Porsche dealer.
The ABS control unit is adjusted for the approved tire dimensions.The use of tires with non-approved dimensions can lead to different wheel speeds, causing ABS to switch off.
Porsche Active Suspension
Management (PASM)
The PASM system actively adjusts the shock absorbers. The adjustable damper system selects the appropriate damping level for each wheel according to the driving situation and driving conditions. Driving safety, agility and comfort are optimized.
Two different chassis setups can be selected at the push of a button:–“ Chassis Normal” –“ Chassis Sport”
In Normal mode the vehicle is in a sporty and comfortable setup.Sport mode offers very sporty shock absorber tuning (e.g. for driving on the race circuit).
In addition to manual mode selection, PASM also adjusts shock absorber tuning for either sporty or comfort driving, depending on the driving situation.
14_991_Turbo_21.book Seite 185 Mittwoch, 9. April 2014 2:19 14

208 Parking
Ultrasound sensors
Maintenance notes
fThe sensors must always be kept free of dust, ice and snow in order to ensure that they are fully functional.fDo not damage sensors by abrasion or scratching.fMaintain sufficient distance when cleaning with high-pressure cleaning equipment.The sensors will be damaged if the pressure is too high.
Signal tones/function
When reverse gear is selected, ParkAssist confirms that it is switched on by issuing a short signal tone .
If the vehicle has front ParkAssist, no signal tone will be issued when reverse gear is selected.Instead, the ParkAssist visual display will appear on the central screen of the Porsche communication system.
A detected obstacle is signaled by an intermittent tone . The intervals decrease as the obstacle is approached.
If the distance drops to less than approx. 12 in. (30 cm), a continuous tone sounds.fSet the radio volume so that the signal tones are not drowned out.
The volume of the signal tones can be changed individually.
For information on changing the signal tone volume:fPlease see the chapter “ADJUSTING PARKASSIST VOLUME” on page 126.
Even when using ParkAssist, the driver is still responsible for taking due care when parking and when assessing obstacles.A continuous tone sounds when there is a risk of collision.fDo not drive rearward any further once a continuous tone sounds.
Limits of ultrasonic measurement
– ParkAssist cannot detect sound-absorbing obstacles (e.g. winter driving, powder snow, clothing made from fabric or fur),– sound-reflecting obstacles (such as glass surfaces and flat painted surfaces),– and very thin obstacles (e.g. thin posts).
Other ultrasound sources (e.g. pneumatic brakes of other vehicles, sweeping machines and jack hammers) can interfere with the detection of obstacles.
Care Required ParkingWARNINGh
14_991_Turbo_21.book Seite 208 Mittwoch, 9. April 2014 2:19 14

236 Maintenance and Car Care
If cleaning agents (e.g. wheel cleaning agents) come into contact with the brake disks, the resulting film on the brake disks can impair braking performance.fMake sure that no cleaning agent comes into contact with the brake disks.fIf cleaning agent has come into contact with the brake disks, clean the brake disks thoroughly with a strong jet of water.fPaying attention to any road users behind you, dry the brake disks by applying the brakes.
Stainless steel tailpipes
Stainless steel tailpipes can discolor due to soiling, strong heat and combustion residues.
The original shine can be achieved again using commercially available metal luster paste or metal polish.
Cleaning door, roof, lid and window seals
The lubricant coating on the inner door seals may be damaged by unsuitable cleaning and care agents.fDo not use any chemical cleaning agents or solvents.fDo not use any preservative agents.
fWash dirt (e.g. abrasion, dust, road salts) from all seals regularly using warm soapy water.fIf there is a risk of frost, protect the outer door seals and the lid and flap seals against freezing into place with a suitable care product.
Leather care
The natural surface markings of leather, e.g. creases, healed scars, insect sting marks, structural differences and slight variations in shade and grain add to the attractiveness of the high-quality natural leather product.
Observe the following care instructions:
The leather will be damaged by the use of unsuitable cleaning and care agents and by inappropriate treatment.fDo not use caustic cleaners or hard cleaning objects!fMake sure that perforated leather does not get wet on its reverse side.fRemove water drops from the leather without delay.
fClean all types of leather regularly to remove fine dust using a soft, damp, white woolen cloth or a commercially available microfiber cloth.fRemove heavy contamination (not water or moisture stains) with a leather cleaner.Always read the instructions for use given on the containers.We recommend Porsche leather care liquid.fTreat cleaned leather only with a leather care product.We recommend Porsche leather care liquid.
Seats with seat ventilation
Care instructions for water or moisture stains.
Rain water or moisture can stain the perforated leather.
Removing water and moisture stains
Preconditions: – Seat heating and seat ventilation must be switched off.– No direct sunlight.– Do not use leather cleaners or care products to remove water and moisture stains.fBlot the entire seat or backrest surface using a clean, absorbent sponge and distilled water.Make sure that the perforated leather does not get wet on its reverse side.fAllow the seat covering to dry completely at room temperature out of direct sunlight.Do not dry the seat covering by switching on the seat heating and seat ventilation.fOnce dry, wipe the seat covering with a dry, lint-free cloth.
Cleaning carpet, floor mats
fUse a vacuum cleaner or a brush (not too soft) for cleaning.fHeavy dirt and stains can be removed with a stain remover.We recommend Porsche stain remover.
To protect carpets, the Porsche range of accessories includes mats of the correct size and with the appropriate fastening.
Cleaning Agents on Brake Disks
WARNINGh
NOTICE
NOTICE
14_991_Turbo_21.book Seite 236 Mittwoch, 9. April 2014 2:19 14

Maintenance and Car Care 237
Improperly secured floor mats can obstruct pedal travel.fAlways check the movement of the pedals before driving and make sure that they are not obstructed by a floor mat or any other object.fSecure the floor mat to prevent it from sliding into positions that could interfere with the safe operation of your vehicle – do not lay them loosely in the vehicle.Your authorized Porsche dealer will be glad to offer you floor mats of correct size including a securing possibility.
Cleaning airbag covers
Incorrect modifications may damage the airbag system. The airbag may not deploy properly in the event of an accident.fDo not make any modifications whatsoever to individual components, such as the padded covers on the steering wheel, the instrument panel, the underside of the instrument panel, front seats and door panels.fHave your authorized Porsche dealer to clean these components.
Cleaning fabric linings
fFabric linings on pillars, roofliner and sun blinds, etc. must be cleaned only using suitable cleaning agents or a suitable dry foam and a soft brush.
Alcantara® care
Do not use leather care products to clean Alcantara®. Alcantara® is a manufactured product. It is not genuine leather or suede.
For regular care, it is sufficient to clean the cover with a soft brush.
Strong abrasion or rubbing when cleaning will produce a lasting change to the surface.
Cleaning when lightly soiled
fWet a soft cloth with water or a neutral soap solution and wipe off the dirt.
Cleaning when heavily soiled
fWet a soft cloth with lukewarm water or thinned white spirit and dab the dirt from the outside in.
Cleaning the safety belts
fUse mild detergent to clean soiled belts.fWhen drying, avoid direct sunlight.fOnly use suitable cleaning agents.fDo not tint or bleach the belts.The belt fabric could be weakened, thus affecting safety.
Storing your Porsche
If you intend to store your Porsche for a prolonged period, please consult your authorized Porsche dealer. The staff will be glad to advise you on the most suitable and necessary methods. fClean your vehicle thoroughly inside and outside. The under carriage and chassis components should be free of dirt and salt deposits. fFill up the fuel tank. fChange the oil and oil filter, and run the engine for several minutes. fIncrease the tire pressure to 50 psi/3.5 bar/350 kPa.It is not recommended to lift the vehicle, due to the possibility of corrosion on shock absorber piston shafts.The vehicle should be moved slightly, approximately every four weeks, to prevent flat spot on the tires.
Climate control
The air conditioning system should be in good working condition and fully charged.
Windshield/Headlight washer
fCheck and correct antifreeze/cleaning solution level as necessary.
Obstructed Pedals
Vehicle Interior Modifications
WARNINGh
DANGERh
14_991_Turbo_21.book Seite 237 Mittwoch, 9. April 2014 2:19 14

Minor Repairs 243
Information
If pure water is added in an emergency, the mixing ratio will have to be corrected.A significant loss of coolant indicates a leak in the cooling system.fThe cause must be eliminated without delay. Please contact an authorized Porsche dealer.
Hands, fingers, items of clothing (ties, sleeves, etc.), necklaces or long hair can be drawn in by moving parts, e.g. the engine-compartment blowers, drive belt, etc., when working in the engine compartment.
The engine-compartment blowers are mounted under the engine compartment lid.After the engine is switched off, the engine compartment temperature is monitored for approx. 30 minutes.During this period, and depending on temperature, the engine-compartment blowers may continue to run or start to run.fCarry out work in this area only with the engine off and exercise extreme caution.
The engine and adjacent components become very hot when the engine is running.fExercise extreme caution when working in the engine compartment.
Brake Fluid
Regular checking of the brake fluid is part of servicing.
The fluid level should always be between the MIN and MAX markings.
A slight decrease in the fluid level due to wear and automatic readjustment of the disk brakes is normal.However, if the fluid level falls significantly or goes below the MIN marking, the brake system may have developed a leak.fHave the brake system checked immediately. Please contact an authorized Porsche dealer.
Brake fluid is hazardous to your health, and may be fatal if swallowed.fKeep brake fluid out of children's reach.fIf brake fluid gets into your eye, immediately rinse with clean water for a few minutes. Then see a doctor immediately.fPlease note all the information on the refill container of the brake fluid.
Brake fluid attacks and can damage paintwork.fImmediately rinse off spilled brake fluid with clean water.
Changing brake fluid
Brake fluid absorbs moisture from the air over time. The absorbed water can impair braking efficiency.fIt is important therefore to have the brake fluid changed in accordance with the change intervals specified in the “Maintenance” booklet.fUse only brake fluid authorized by Porsche.
Brake warning light USA
Brake warning light Canada
The warning light on the instrument panel and the warning message on the multi-function display alert you to the fact that the brake fluid level is too low and could indicate brake circuit failure if the pedal travel is greater than normal.
Engine-compartment blowers or other moving parts in the area of the engine
Hot engine parts
WARNINGh
WARNINGh
Swallowing Brake FluidDANGERh
NOTICE
14_991_Turbo_21.book Seite 243 Mittwoch, 9. April 2014 2:19 14

290 Index
Index
AA/C button Air-conditioning system .......................................56A/C MAX buttonAir-conditioning system .......................................56ABD (automatic brake differential)Functional description .......................................182ABS (anti-lock brake system)Functional description .......................................184Warning light on instrument panel ......................185ACCAdaptive cruise control .....................................157Active Safe (PAS)Settings in multi-purpose display........................128Adaptive cruise control ................................................157Display principle ...............................................160Exceptions.......................................................165Functional description .......................................157Interrupting/resuming control ............................164Operating principle ...........................................159Operating states ..............................................161Porsche Active Safe .........................................167Radar sensor ...................................................158Setting the desired distance ..............................162Setting/changing desired speed ........................161Switching on/off...............................................161 Adaptive light system, driving light assistant ....................79Adhesive foils, care instructions ....................................235Adjusting seat position ...................................................32Aftermarket Alarms......................................................169Air cleaner, maintenance instructions ............................244Air distribution ...............................................................58Air vents Adjusting ...........................................................59Opening/closing .................................................59AirbagAirbag warning light on the tachometer ................42Automatic deactivation of the passenger airbag....41Care instructions ..............................................237Disposal ............................................................39Function ............................................................39Functional description .........................................38Installation location .............................................38Passenger airbag warning light............................42Air-conditioning compressorInformation on air-conditioning compressor ..........55
Air-conditioning system Automatic load switch-off ................................... 55Extended ventilation panel .................................. 59Information on air-conditioning compressor.......... 55Setting air distribution ........................................ 58Setting air quantity............................................. 58Setting automatic air-recirculation mode .............. 57Setting temperature ........................................... 58Switching A/C MAX mode on/off ......................... 56Switching A/C mode on/off ................................ 56Switching air-conditioning compressor on/off....... 56Switching air-recirculation mode on and off .......... 57Temperature sensor ........................................... 55 Air-recirculation button Air-conditioning system ...................................... 57 Alarm button................................................................. 17Alarm system Avoiding false alarms ....................................... 217Functional description ...................................... 216Persons/animals remaining in the locked vehicle 216Switching off ................................................... 216Switching off interior surveillance and inclination sensor............................................. 216Switching on ................................................... 216 Alcantara, care instructions ......................................... 237Alloy wheels Care instructions ............................................. 235Inscription ....................................................... 253Allwheel driveFunctional description ...................................... 180Torque distribution ................................... 114, 116AlternatorVehicle electrical system warning ........................ 95 Aluminum rims Care instructions ............................................. 235Inscription ....................................................... 253 Ambient lighting ............................................................ 84Antifreeze in coolant ........................................................ 242In washer fluid ................................................. 224Anti-lock brake system (ABS)Functional description ...................................... 184Anti-slip control (ASR)Functional description ...................................... 182ArmrestOpening front oddments tray ............................ 194AshtrayEmptying ........................................................ 195
Opening .......................................................... 195 ASR (Anti-slip control) Functional description....................................... 182 Assigning MFS button (◊ )............................................. 127 Assistance systemsActive Safe (PAS) ............................................. 128Assistance when driving uphill Functional description....................................... 184 AudioTips ................................................................ 168 Audio interface, installation position .............................. 171AUTO (light switch) ........................................................ 79 Driving light assistant ......................................... 79 Auto Start Stop function Display ............................................................ 151Exceptions ...................................................... 149Operating principle ........................................... 149Preconditions................................................... 149Starting engine automatically ............................ 149Stopping engine automatically........................... 149Switching on and off................................. 150, 175 Automatic brake differential (ABD) Functional description....................................... 182Automatic Coming Home lights, courtesy lighting Entry function .................................................... 80Welcome Home function ..................................... 80 Automatic driving light assistant High Beam Assistant .......................................... 81 Automatic speed control (cruise control)Accelerating .................................................... 156Decelerating .................................................... 156Functional description....................................... 155Interrupting operation ....................................... 156Storing speed .................................................. 156Switching off ................................................... 157Switching on .................................................... 156 Automatic transmission................................................ 172AUX interface, installation position ................................ 171
BBaby seat Installing with LATCH system............................... 46LATCH restraint system ...................................... 46Prescribed installation direction (depending onweight of child) .................................................. 43BatteryCare ............................................................... 272
14_991_Turbo_21.book Seite 290 Mittwoch, 9. April 2014 2:19 14