stop start RENAULT CLIO 2009 X85 / 3.G User Guide

Downloaded from www.Manualslib.com manuals search engine
stopping the engine ..............................(up to the end of the DU)engine start/stop button ........................(up to the end of the DU)driving ...................................................(up to the end of the DU)starting the engine ................................(up to the end of the DU)
2.4
ENG_UD10550_1Démarrage / arrêt moteur : véhicule avec clé / télécom\
mande à radiofréquence (X85 - B85 - C85 - S85 - K85 - Renault)ENG_NU_853-3_BCSK85_Renault_2
Starting/stopping the engine using the key
Stopping the engine
With the engine idling, turn the key back to the Stop position.
ÉDiesel injection
Cold or warm engine
– Turn the key to the “Start” posi
- tion D without depressing the accelerator pedal.
– Release the key as soon as the
engine starts.
Note: several seconds may pass be- tween turning the key and the engine starting to allow for engine preheating.
Starting the engine
Petrol injection
Engine warm or cold
– Run the starter
without depress- ing the accelerator.
– Release the key as soon as the
engine starts.
STARTING/STOPPING THE ENGINE: vehicle with key
Driver’s responsibility
Never leave your vehi- cle with the key inside and never leave a child (or a pet) unsupervised, even for a short while.
There is a risk that they could start the engine or operate electrical equipment (electric windows etc.) and trap part of their body (neck, arms, hands, etc.).Risk of serious injury.
Never switch off the ignition before the vehicle has stopped completely. Once the engine has stopped, the brake servo, power-assisted steer- ing, etc., and the passive safety de- vices such as the airbags and pre- tensioners will no longer operate.

Downloaded from www.Manualslib.com manuals search engine
stopping the engine ..............................(up to the end of the DU)engine start/stop button ........................(up to the end of the DU)RENAULT carduse ..................................................(up to the end of the DU)starting the engine ................................(up to the end of the DU)driving ...................................................(up to the end of the DU)child safety.............................................................(current page)
2.5
ENG_UD10551_1Démarrage moteur : véhicule avec carte Renault (X85 - B85 - C85 -\
S85 - K85 - Renault)ENG_NU_853-3_BCSK85_Renault_2
Starting - stopping the engine using the RENAULT card
Starting conditions.
Follow the starting instructions on the
instrument panel 2 describing the fol- lowing conditions:
to start, depress the brake pedal or clutch (the pedal must be depressed through-
out starting) and press button 3.
If a gear is engaged, the vehicle may only be started by depressing the clutch pedal.
RENAULT card
The card must be in detection zone 1 (passenger compartment and luggage compartment, except for some high areas such as the sun visor, spectacle holder, dashboard upper section, etc.)
or in card reader 4.
STARTING THE ENGINE: vehicle with RENAULT CARD (1/3)
1
2
34
Driver’s responsibilityNever leave your vehicle with the RENAULT card inside and never leave a child (or a pet) unsupervised, even for a short while.The reason for this is that the child may endanger himself or others by starting the vehicle, activating equip- ment such as the windows, or lock- ing the doors.Risk of serious injury.

Downloaded from www.Manualslib.com manuals search engine
stopping the engine ..............................(up to the end of the DU)engine start/stop button ........................(up to the end of the DU)RENAULT carduse ..................................................(up to the end of the DU)driving ...................................................(up to the end of the DU)
2.8
ENG_UD12574_2Arrêt moteur : véhicule avec carte Renault (X85 - B85 - C85 - S85\
- K85 - Renault)ENG_NU_853-3_BCSK85_Renault_2
When you leave your vehi- cle, especially if you have your RENAULT card with you, check that the engine is completely switched off.
To ensure that the engine is completely
stopped, press button 3 twice.
The steering locks. Check that it is cor- rectly locked in position.
With the engine switched off, any ac- cessories being used (radio, heating and air conditioning, etc.) will continue to function for a few minutes.
When the driver’s door is opened, the accessories stop working.
Conditions for stopping the
engine
Before stopping the engine, make sure you have your card.
When the vehicle is stationary, press
button 3.
If the card is not in the detection zone after pressing once, the messages ‘Confirm engine stop’ and ‘Press STOP
twice’ appear on instrument panel 2.
STOPPING THE ENGINE: vehicle with RENAULT CARD
3
2
Driver’s responsibility
Never leave your vehicle with the RENAULT card inside and never leave a child (or a pet) unsupervised, even for a short while.
There is a risk that they could start the engine or operate electrical equipment (electric windows etc.) and trap part of their body (neck, arms, hands, etc.).Risk of serious injury.
Never switch off the ignition before the vehicle has stopped completely. Once the engine has stopped, the brake servo, power-assisted steer- ing, etc. and the passive safety de- vices such as air bags and preten- sioners will no longer operate.

Downloaded from www.Manualslib.com manuals search engine
driving ...................................................(up to the end of the DU)filterparticle filter ....................................(up to the end of the DU)special features of diesel vehicles with particle filter
(up to the end of the DU)
2.11
ENG_UD10555_1Particularités des versions diesel avec filtre à particules (X85 \
- B85 - C85 - S85 - K85 - Renault)ENG_NU_853-3_BCSK85_Renault_2
As a guide, this type of cleaning should take up to 20 minutes.
If the © warning light comes on, accompanied by the message “Check antipollution”, consult an approved Dealer as soon as possible.
Diesel engine speed
Diesel engines are fitted with injection equipment which prevents the engine speed being exceeded irrespective of the gear selected.
Special features of diesel versions fitted with a particle filter
Do not park the vehicle or
run the engine in locations where combustible sub- stances or materials such as grass or leaves can come into con- tact with the hot exhaust system.
When driving, depending on the grade of fuel used, it is possible that white smoke may be emitted.
This is due to the exhaust particle filter being cleaned automatically, and does not affect the way the vehicle runs.
Warning light
1 Ü comes on to indi- cate a filter saturation risk.
To clean the particle filter, for 60 miles (100 km) after the message appears, drive at an average speed of at least 24 mph (40 km/h), where suitable traf- fic conditions and the speed limit will allow, until the warning light goes out. You may need to restart the operation if the vehicle has to stop before the warn- ing light goes out.
DIESEL VERSIONS WITH PARTICLE FILTER
1

Downloaded from www.Manualslib.com manuals search engine
2.14
ENG_UD10558_1Conseils antipollution, économies de carburant, conduite (X85 - B85 \
- C85 - S85 - K85 - Renault)ENG_NU_853-3_BCSK85_Renault_2

JauneNoirNoir texte

– Brake as little as possible by suitably anticipating an obstacle or bend and then simply releasing the accelerator pedal.
– Avoid sudden acceleration.
– Do not overrev the engine in the in
- termediate gears.
Always use the highest gear possi- ble without labouring the engine.
On versions with an automatic trans- mission, it is preferable to keep the
gear lever in position D.
– Do not try to maintain the same
speed up a hill, accelerate no more than you would on level roads. Keep your foot in the same position on the accelerator pedal.
– Double declutching and accelerating
before switching off the engine are unnecessary in modern vehicles.
– Bad weather, flooded roads.
Do not drive through floods if the depth of water is above the lower edge of the wheel rims.
Exhaust gas monitoring
system
The exhaust gas monitoring system will detect any operating faults in the vehicle’s antipollution system.
If this system malfunctions, toxic sub- stances may be released into the at- mosphere or damage may occur.
ÄThis warning light on the in- strument panel will indicate if there are any faults in the system:This lights up when the ignition is switched on and goes out when the engine is started.
– If it lights up continuously, consult
your approved dealer as soon as possible;
– if it flashes, reduce the engine speed
until the light stops flashing. Contact your approved dealer as soon as possible.
Driving
– Drive carefully for the first few miles until the engine reaches its normal operating temperature, rather than let it warm up while the vehicle is sta- tionary.
– Speed is expensive.
– Sporty driving uses a lot of fuel: drive
with a light right foot.
ADVICE: antipollution, fuel economy and driving (2/3)

Downloaded from www.Manualslib.com manuals search engine
automatic gearbox (use) .......................(up to the end of the DU)changing gear .......................................(up to the end of the DU)driving ...................................................(up to the end of the DU)automatic gearbox selector lever..........(up to the end of the DU)
2.31
ENG_UD12577_2Boîte automatique (X85 - B85 - C85 - S85 - K85 - Renault)ENG_NU_853-3_BCSK85_Renault_2
Automatic gearbox
Operation
With gear lever 1 in position P, start the engine.
With your foot on the brake pedal (warn-
ing light 4 goes out), move the lever out of position P.
Only engage D or R when the vehi- cle is stopped, with your foot on the brake and the accelerator pedal re- leased.
You must apply the brake before pressing unlocking button 2 to move out of position P.
Selector lever 1
P: park
R: reverse
N: neutral
D: automatic mode
3:
displays gear engaged in manual mode.
AUTOMATIC TRANSMISSION (1/3)
1
3
Driving in automatic mode
Move lever 1 to position D.
In most traffic conditions, you will not have to touch the gear selector lever again: the gears will change automati- cally at the right time and at the most suitable engine speed because the au- tomatic system takes into account the vehicle load and road contour and ad- justs itself to the particular driving style you have chosen.
Economical driving
When driving, always leave the lever in position D, keeping the accelerator pedal lightly depressed to ensure au- tomatic gear changes at comparatively low engine speeds.
Accelerating and overtaking
Depress the accelerator pedal firmly and fully (so that it goes beyond the kickdown point).
This will enable you to change down to the optimum gear within the engine range.
4
2

Downloaded from www.Manualslib.com manuals search engine
3.6
ENG_UD12673_2Chauffage / air conditionné (X85 - B85 - C85 - S85 - K85 - Renault)ENG_NU_853-3_BCSK85_Renault_3

JauneNoirNoir texte

HEATING, AIR CONDITIONING (3/4)
Position x
In this position:
– the air conditioning stops automati
-
cally even if button F is activated (the indicator light remains lit);
– the ventilation speed of air in the
passenger compartment is zero;
– there is, however, a slight flow of air
when the vehicle is moving.
This position should not normally be used.
Adjusting the ventilation
speed
Normal use
Turn control
C to one of the four posi- tions to start the ventilation system and adjust the power.
Select position  for minimum ventila-
tion and position y for maximum ven- tilation.
Adjusting the air temperature
Turn control B to obtain the desired temperature. The further the pointer is in the red, the more the temperature will be increased.
Switching air conditioning on
or off
The air conditioning is switched on (in- dicator light illuminated) or off (indicator
light extinguished) using button F.
The air conditioning system is used for:
– lowering the temperature inside the
passenger compartment;
– e l i m i n a t i n g c o n d e n s a t i o n m o r e
quickly.
The air conditioning does not operate when the exterior temperature is low.
B
C
F

Downloaded from www.Manualslib.com manuals search engine
3.10
ENG_UD12579_2Air conditionné automatique (X85 - B85 - C85 - S85 - K85 - Renault)\
ENG_NU_853-3_BCSK85_Renault_3

JauneNoirNoir texte

Adjusting automatic mode
The automatic mode is the system’s normal operating mode (AUTO light on) but you may alter the selections made by the system (air distribution, etc.).
These options are explained on the fol- lowing pages.
AUTOMATIC CLIMATE CONTROL (3/8)
This is the recommended mode of use: the automatic heating and air conditioning system guarantees comfort (except in the event of ex- treme conditions) in the passenger compartment and good visibility while optimising consumption.
Return to automatic mode as
soon as possible.
Ambient temperature:
automatic mode (continued)
Operation
To reach and keep the chosen comfort level and to maintain good visibility, the system controls:
– ventilation speed;
– air distribution;
– air recirculation management;
– air conditioning start/stop;
– the air temperature.
The displayed temperature values show a comfort level.
When starting the engine, increasing or decreasing the value displayed will not allow the comfort level to be reached any more quickly. The system will always optimise the tem- perature increase or decrease (the ventilation system does not start in- stantly at maximum speed: it gradu- ally increases). This may take several minutes.
Generally speaking, unless there is a particular reason not to, the dashboard air vents should remain open.

Downloaded from www.Manualslib.com manuals search engine
3.12
ENG_UD12579_2Air conditionné automatique (X85 - B85 - C85 - S85 - K85 - Renault)\
ENG_NU_853-3_BCSK85_Renault_3

JauneNoirNoir texte

Note: the Clear View function auto- matically activates the air conditioning system (indicator light on). Press but-
ton 6 to return to automatic mode.
AUTOMATIC CLIMATE CONTROL (5/8)
In automatic mode, in cold weather, the ventilation will not start imme- diately at maximum power but will increase progressively until the engine temperature is warm enough to heat the passenger compartment air. This may take from a few sec- onds to several minutes.
Varying the ventilation speed
In automatic mode, the system uses the most suitable amount of air to reach and maintain the desired comfort level.
Automatic mode is switched off by
pressing buttons 9 and 11.
These buttons allow you to increase or decrease ventilation speed. If you set it to zero, the system switches off.
Switching air conditioning on
or off
In automatic mode, the system switches the air conditioning system on or off, depending on the climate conditions.
Exit automatic mode by pressing
button 3: the AUTO warning light on
display 5 goes out.
Button
3 activates (display warning light comes on) or stops (warning light goes out) the air conditioning function.
356
9
11

Downloaded from www.Manualslib.com manuals search engine
rear bench seat.....................................(up to the end of the DU)rear seatsfunctions .........................................(up to the end of the DU)
3.30
ENG_UD10581_1Banquette arrière : fonctionnalités (X85 - B85 - C85 - S85 - K85 \
- Renault)ENG_NU_853-3_BCSK85_Renault_3
JauneNoirNoir texte
Then lift up the rear section of cushion 1 and tilt the seat base so that it is next to the front seats.
To fold down the seatback
Remove the rear headrests (if fitted).
Ensure that the front seats are far enough forward.
Place the seat belts in their guides
B.
Press button 2 and lower the seat-
back C.
Rear bench seat: functions
Before moving the seatback, put the seat belt in belt guide B to avoid damaging it.
For safety reasons, carry out any adjustments when the vehicle is not being driven.
The configuration of the two seat bench with the small seatback C pulled down, does not allow the central seat to be used as it would be impossible to buckle the seat belt (belt buckles inaccessible).
The seat base and the seatback may be folded down (one or both sections) to allow bulky objects to be carried.
Start by folding down the seat base, then the seatback.
To fold away the seat base
Lift up the front of the seat cushion A until it reaches the stop.
Where the bench seat is in one section, check that the two sides of the seat base are correctly locked.
REAR BENCH SEAT: functions (1/2)
A
1
C
B
2