wheel bolts RENAULT KANGOO 1997 KC / 1.G Electrical Equipment Workshop Manual
[x] Cancel search | Manufacturer: RENAULT, Model Year: 1997, Model line: KANGOO, Model: RENAULT KANGOO 1997 KC / 1.GPages: 83
Page 15 of 83
IMMOBILISER
Coded key immobiliser system
82
Removal - Refitting
The dashboard must be partially removed to re-
move the decoder unit.
Remove:
- the steering wheel with the wheels straight,
- the half cowlings under the steering wheel,
- the knee protector under the steering column,
- the lights and wiper controls,
- the instrument panel surround,
- the instrument panel,
- the ashtray, its mounting and the two dash-
board mounting bolts on the heating unit,
- the trim at the bottom of the dashboard on the
driver’s side,
- the two speaker grilles on the dashboard,
- the dashboard mountings.
13065R1
Move the dashboard as far back as possible, dis-
connect the decoder unit and remove the two
mounting bolts (B) using a small ratchet fitted
with a Torx 20 socket.
•A red immobiliser warning light on the instru-
ment panel used to :
- indicate activation of the engine immobiliser
system,
- signal a fault in the system for vehicles with a
coded solenoid valve (diesel) or non-
recognition of the key,
- signal entry into the door locking remote
control resynchronisation mode (depending
on equipment).
• An injection warning light (petrol vehicle)
which indicates a fault in the:
- injection,
- engine immobiliser system when the engine
is running (flashes during deceleration and
at idle speed).
82-4
Page 28 of 83
INSTRUMENT PANEL
Dashboard
REMOVAL
Disconnect the battery.
Removing the steering wheel (with AIRBAG)
83
PRB5702
12973S
Remove the two airbag cushion bolts behind the
steering wheel.
Disconnect the connectors (airbag, horn).
Remove:
- the airbag cushion,
- the steering wheel bolt (renew it on refitting,
pre-bonded bolt, tightening torque: 4.5
daN.m),
- the steering wheel after setting the wheels
straight.
Removing the steering wheel (without AIRBAG)
Remove:
- the central cushion,
- the steering wheel bolt (renew it on refitting,
pre-bonded bolt, tightening torque: 4.5
daN.m),
- the steering wheel after setting the wheels
straight.
83-1
Page 30 of 83
INSTRUMENT PANEL
Dashboard
83
Remove:
- the lower protector (four bolts),
- the lower section of the dashboard (four bolts,
two clips),
Special notes for vehicles with airbag
Before removing the assembly, the position of the
rotary switch under the steering wheel must be
noted:
- by ensuring that the wheels are straight on re-
moval so that the strip may be positioned in the
centre,
- by immobilising the rotary switch rotor using
adhesive tape.
Slacken the bolt then sharply tap the screwdriver
to release the cone.
Disconnect the connectors.
12967-1R
12966R
12971-1R
83-3
Page 41 of 83
CONTROLS - SIGNALS
Windscreen wiper stalk
REMOVAL - REFITTING
Disconnect the battery.
Remove the two half cowlings under the steering
wheel.
Release the immobiliser antenna ring or the pla-
stic surround from the ignition switch.
Remove the two mounting bolts (A) for the wiper
stalk.
Release the stalk from its mounting and dis-
connect the connector.
84
CONNECTION
12970R
NOTE : the steering wheel does not have to be re-
moved.
13061R
Track Allocation
A1 Front timer
A2 Wiper high speed
A3 Wiper low speed
A4 Front washer pump
A5 Not used
A6 Intermittent slow speed
A7 + after ignition, front wiper
B1 Rear washer pump
B2 Rear timer
B3 Not used
B4 + after ignition, rear wiper
B5 Earth
B6 Not used
B7 Not used
84-1
Page 42 of 83
CONTROLS - SIGNALS
Lights stalk
REMOVAL - REFITTING
Disconnect the battery.
Remove the two half cowlings under the steering
wheel.
Remove the two mounting bolts (B) for the lights
stalk.
Release the stalk from its mounting and dis-
connect the connector.
84
CONNECTION
12970R1
NOTE : the steering wheel does not have to be re-
moved.
13062R
Track Allocation
A1 Front fog lights
A2 Not used
A3 Rear fog light
A4 Horn
A5 Right hand indicators
A6 Central flasher unit
A7 Left hand indicators
B1 Side lights
B2 + before ignition, side lights
B3 + before ignition, dipped headlights
B4 Not used
B5 Dipped headlights
B6 + before ignition, main beam headlights
B7 Main beam headlights
84-2
Page 44 of 83
CONTROLS - SIGNALS
Rotary switch under steering wheel
This makes the electrical connection between the
steering column and the steering wheel.
It consists of a strip of conductor tracks (airbag)
whose length is designed to guarantee 2.5
steering wheel turns (steering lock plus safety
margin) on each side.
REMOVAL - REFITTING
84
- the horn connector, if fitted,
- the steering wheel bolt,
- the steering wheel after setting the wheels
straight,
- the half cowlings (3 bolts).
Disconnect the connector for the rotary switch
and remove it after removing the three mounting
bolts (E).
Before removing the rotary switch its position
must be noted:
- by ensuring that the wheels are straight on re-
moval so that the track may be positioned in
the centre,
- by immobilising the rotary switch rotor using
adhesive tape.
If it is being replaced, the new part is supplied rea-
dy centred by an adhesive label which will tear off
as soon as the steering wheel is turned for the first
time (fit with the wheels straight).
12970R3
Disconnect the battery.
Remove:
- the airbag cushion by the two torx T30 bolts
(tightening torque : 0.5 daN.m) located behind
the steering wheel and disconnect the connec-
tor (D),
IMPORTANT: It is not permitted to operate the
pyrotechnical systems (airbags and pretensioners)
near a source of heat or flame as there is a risk of
triggering.
IMPORTANT : If the steering wheel is removed,
the airbag connector (D)
MUST be disconnected.
The airbag has a connector which short circuits if
it is disconnected to prevent incorrect triggering.
12973R
84-4
Page 60 of 83
WIRING
Remote control for door locking
88
Ignition off:
1.Press and hold the central door locking button
for a few seconds until the doors lock and un-
lock.
From this moment, the operator has 10 se-
conds to carry out the next operation.
NOTE: The 10 seconds are shown by the illu-
mination of the red immobiliser warning light
(if fitted) and bargraph 17 LH on the XR25
(code
D56, fiche n° 56).
2.Press the remote control twice (the doors lock
and unlock and the red warning light extin-
guishes, if fitted).
NOTE : If both remote controls (if fitted) are
desynchronised, two resynchronisation proce-
dures will have to be carried out (one for each
remote control).
IMPORTANT: To ensure that the infrared code
is correctly transmitted it is essential to direct
the transmitter correctly towards the receiver.
If the procedure fails it will be necessary to
restart from the beginning (infrared remote
control only).
3.The procedure is complete - check that the
doors lock correctly.
Removal - Refitting
The dashboard must be partially removed to re-
move the decoder unit.
Remove:
- the steering wheel with the wheels straight,
- the half cowlings under the steering wheel,
- the knee protector under the steering column,
- the lights and wiper controls,
- the instrument panel surround,
- the instrument panel,
- the ashtray, its mounting and the two dash-
board mounting bolts on the heating unit,
- the trim at the bottom of the dashboard on the
driver’s side,
- the two speaker grilles on the dashboard,
- the dashboard mountings.
THE DECODER UNIT
The decoder unit is located in the left hand side of
the dashboard (A).
12967R
88-5
Page 76 of 83
WIRING
Airbags and seat belt pretensioners
88
12973R
Remove:
- the airbag cushion by its two Torx bolts (tighte-
ning torque: 0.5 daN.m) located behind the
steering wheel and disconnect connector (D),
- the steering wheel bolt,
- the steering wheel after straightening the
wheels.
NOTE: For these vehicles, the computer may be
locked using the XR25 and command G80* (ISO
selector on S8 code D49) during the operation.
When this function is active, all the trigger lines
are inhibited, the airbag warning light on the ins-
trument panel and bargraph 14 LH on the XR25 il-
luminate (new computers are supplied in this
condition).
After the operation, carry out a check using the
XR25. If everything is correct, unlock the compu-
ter using command G81*.
IMPORTANT : before scrapping a non-triggered
airbag cushion it
MUST be destroyed in accor-
dance with the method for destruction (see sec-
tion "Destruction procedure": destruction of part
removed from the vehicle).
STEERING WHEEL AIRBAG AND ROTARY SWITCH
REMOVAL
IMPORTANT: The pyrotechnic systems (airbag
and pretensioners) must not be handled near a
heat source or flame; there is a risk of triggering.
IMPORTANT : If the steering wheel is removed,
the airbag connector
MUST be disconnected (D) .
The airbag connector short circuits when it is dis-
connected to prevent incorrect triggering.
88-21