ignition RENAULT KANGOO 2013 X61 / 2.G Lighting Workshop Manual
[x] Cancel search | Manufacturer: RENAULT, Model Year: 2013, Model line: KANGOO, Model: RENAULT KANGOO 2013 X61 / 2.GPages: 30, PDF Size: 0.24 MB
Page 14 of 30
80D-14V1 MR-376-X76-80D000$060.mif
80D
UCH
Vdiag No.: 0F
NOTESOnly perform this conformity check after a complete check with the diagnostic tool.
The values indicated in this conformity check are given as examples.
Test conditions: Engine stopped, ignition on.
FunctionParameter or status
Checked or actionDisplay and Notes Fault finding
Lighting
controlET484Side lights signalPresent during command
for side lights In the event of a fault, apply
the interpretation of status
ET484.
ET485Hazard warning
lights signalPresent during command
for hazard warning lightsIn the event of a fault, apply
the interpretation of status
ET485.
ET486Right-hand
direction indicator
signalPresent during command
for right-hand direction
indicatorIn the event of a fault, apply
the interpretation of status
ET486.
ET487Left-hand direction
indicator signalPresent during command
for left-hand direction
indicatorIn the event of a fault, apply
the interpretation of status
ET487.
UCH_V0F_CCONF
LIGHTING
Fault finding – Conformity check
Page 19 of 30
80D-19
AFTER REPAIRCarry out another fault finding check on the system.
Deal with any other faults.
Clear the stored faults.
V1 MR-376-X76-80D000$080.mif
LIGHTING
Fault finding – Interpretation of statuses80D
UCH
Vdiag No.: 0F
ET486
ET487RIGHT-HAND INDICATOR SIGNALLEFT-HAND INDICATOR SIGNAL
NOTESThere must be no present or stored faults.
Switch on the ignition.
Activate the left or right direction indicator control.
The status should be PRESENT.
Special note:
Use Wiring Diagrams Technical Note for Kangoo VLL.
"ABSENT"
Check for the presence and condition of supply fuse F31 (10 A) on the passenger
compartment fuse and relay box, component code 260 (see MR 374 Mechanical,
81C, Fuses, Fuses: List and location of components).
Check the connection and condition of the direction indicator stalk connector,
component code 209 and the UCH connector, component code 645.
If the connector or connectors are faulty and there is a repair procedure (see
Technical Note 6015A, Electrical wiring repair, Wiring: Precautions for repair),
repair the connector, otherwise replace the wiring.
Check the operation of the indicator light stalk in the left-hand indicator position:
Check the continuity between connections 64T and NA.
Check the operation of the direction indicator stalk in the right-hand indicator position:
Check the continuity between connections 64S and NA.
Check the continuity of connection NA of component 209.
If the connection is faulty and there is a repair procedure (see Technical Note 6015A,
Electrical wiring repair, Wiring: Precautions for repair), repair the wiring,
otherwise replace it.
Disconnect the connectors of the UCH, the right-hand indicator, and the left-hand
indicator.
Check the continuity and insulation of the following connections:
•64S between components 209 and 645,
•64T between components 209 and 645.
If the connection or connections are faulty and if there is a repair procedure (see
Technical Note 6015A, Electrical wiring repair, Wiring: Precautions for repair)
repair the wiring, otherwise replace it.
If the fault is still present, contact the techline.
UCH_V0F_ET486/UCH_V0F_ET487
Page 21 of 30
80D-21
AFTER REPAIRCarry out a road test and then a check using the diagnostic tool.
V1 MR-376-X76-80D000$100.mif
80D
UCH
Vdiag No.: 0F
AC022LEFT-HAND INDICATOR
NOTESThis command is used to activate the left-hand direction indicators.
There must be no present or stored faults.
Check the conformity of the left-hand direction indicator bulbs.
Switch on the ignition.
Special Note:
Use Wiring Diagrams Technical Note for Kangoo VLL.
Check for the presence and condition of supply fuse F31 (10 A) on the passenger compartment fuse and relay box,
component code 260 (see MR 374 Mechanical, 81C, Fuses, Fuses: List and location of components).
Check the connection and condition of the indicator control stalk connector, component code 209, and the UCH
connector, component code 645.
If the connector or connectors are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Check the operation of the indicator light stalk in the left-hand indicator position:
Check the continuity between connections 64T and NA of component 209.
Check the continuity of connection NA of component 209.
If the connection is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
UCH_V0F_AC022
LIGHTING
Fault finding – Interpretation of commands
Page 23 of 30
80D-23
AFTER REPAIRCarry out a road test and then a check using the diagnostic tool.
V1 MR-376-X76-80D000$100.mif
LIGHTING
Fault finding – Interpretation of commands80D
UCH
Vdiag No.: 0F
AC023RIGHT-HAND DIRECTION INDICATOR
NOTESThis command is used to activate the right-hand direction indicators.
There must be no present or stored faults.
Check the conformity of the right-hand direction indicator bulbs.
Switch on the ignition.
Special Note:
Use Wiring Diagrams Technical Note for Kangoo VLL.
Check for the presence and condition of supply fuse F31 (10 A) on the passenger compartment fuse and relay box,
component code 260 (see MR 374 Mechanical, 81C, Fuses, Fuses: List and location of components).
Check the connection and condition of the indicator control stalk connector, component code 209, and the UCH
connector, component code 645.
If the connector(s) are faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Check the operation of the indicator control stalk in the right-hand indicator position:
Check the continuity between connections 64S and NA of component 209.
Check the continuity of connection NA of component 209.
If the connection is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace the wiring.
UCH_V0F_AC023
Page 25 of 30
80D-25
AFTER REPAIRCarry out a road test and then a check using the diagnostic tool.
V1 MR-376-X76-80D000$100.mif
LIGHTING
Fault finding – Interpretation of commands80D
UCH
Vdiag No.: 0F
AC145FRONT COURTESY LIGHTS
NOTESThis command is used to activate the front courtesy light.
There must be no present or stored faults.
Check the conformity of the courtesy light bulbs.
Switch on the ignition.
Special note:
Use Wiring Diagrams Technical Note for Kangoo VLL.
Check the connection and condition of the courtesy light console, component code 265 and the UCH connector,
component code 645.
If the connector(s) are faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Check the continuity between the following connections:
•BPT between components 265 and 645,
•13E between components 265 and 645,
•MK between components 265 and earth.
If the connection or connections are faulty and if there is a repair procedure (see Technical Note 6015A,
Electrical wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace the wiring.
Check the continuity of connection MK of component 265.
If the connection is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace the wiring.
If the fault is still present, contact the techline.
UCH_V0F_AC145