ABS RENAULT KANGOO 2013 X61 / 2.G Petrol V42 Injection Owner's Manual

17B-64V2 MR-376-X76-17B050$082.mif
PETROL INJECTION
Fault finding – Interpretation of faults17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 05, 06,
14, 16, 18
AFTER REPAIRFollow the instructions to confirm repair.
Deal with any other faults.
Clear the stored faults.
DF093
CONTINUED
CONOTESNone.
Check the condition of the fuse of the supply circuit for the downstream oxygen sensor, component code 242.
If the fuse is faulty, check all the following steps and replace the fuse (see MR 388 (Logan and Sandero), MR 451
(Duster), MR 423 (Thalia 2/Symbol 2), MR 430 (Clio II F 6) or MR 374 (Kangoo VLL), Mechanical, 81C, Fuses,
Fuses: List and location of components).
Read the stored speed within the context of the fault using PR089 Vehicle speed.
If the value is 0, drive the vehicle to reach a speed of 6 mph (10 km/h) and check PR089 again.
If the value of this parameter is 0 whilst driving, apply the fault finding procedure for DF091 Vehicle speed signal,
abandoning the steps described below. If PR089 operates normally, follow the fault finding procedure for this fault.
Check the cleanliness and condition of the injection computer connector, component code 120 and of the
connector of the downstream oxygen sensor, component code 242.
If the connector or connectors are faulty and if there is a repair procedure (see Technical Note 6015A, Repairing
electrical wiring, Wiring: Precautions for repair), repair the connector(s), otherwise replace the wiring.
Check the insulation, continuity and the absence of interference resistance on the following connections:
–3GJ between components 120 and 242,
–3GL between components 120 and 242.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring. Otherwise replace the wiring.
If the fault is still present, replace the downstream oxygen sensor, component code 242 (see MR 388 (Logan and
Sandero), MR 451 (Duster), MR 423 (Thalia 2/Symbol 2), MR 430 (Clio II F 6) or MR 374 (Kangoo VLL),
Mechanical, 17B, Petrol injection, Oxygen sensors: Removal - Refitting).
If the fault is still present, contact the Techline.

17B-65V2 MR-376-X76-17B050$082.mif
PETROL INJECTION
Fault finding – Interpretation of faults17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 05, 06,
14, 16, 18
AFTER REPAIRFollow the instructions to confirm repair.
Deal with any other faults.
Clear the stored faults.
DF095
PRESENT OR
STOREDTHROTTLE POTENTIOMETER CIRCUIT GANG 11.DEF: Signal incoherent
WARNING
Never drive the vehicle without having confirmed that no faults involving the throttle valve are present.
NOTESSpecial notes:
OBD warning light and level 1 fault warning light illuminate,
The throttle no longer operates.
See the Wiring Diagrams Technical Note for Logan, Sandero, Duster, Thalia 2/
Symbol 2, Clio II F 6, Kangoo VLL.
Check the cleanliness of the throttle valve, component code 1076 and that the throttle rotates properly (no
resistance point)
Check the cleanliness and condition of the throttle valve connector.
If the connector is faulty and there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Check the cleanliness and condition of the injection computer connector, component code 120.
If the connector or connectors are faulty and if there is a repair procedure (see Technical Note 6015A, Repairing
electrical wiring, Wiring: Precautions for repair), repair the connector(s), otherwise replace the wiring.
Check the insulation, continuity and the absence of interference resistance on the following connections:
–3MO between components 120 and 1076,
–3MP between components 120 and 1076,
–3MN between components 120 and 1076.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the throttle valve has been replaced, reinitialise the programming by running command RZ031 Throttle stop
programming.
If the fault is still present, contact Techline.
V42_V04_DF095/V42_V05_DF095/V42_V06_DF095/V42_V14_DF095/V42_V16_DF095/V42_V18_DF095

17B-66V2 MR-376-X76-17B050$082.mif
PETROL INJECTION
Fault finding – Interpretation of faults17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 05, 06,
14, 16, 18
AFTER REPAIRFollow the instructions to confirm repair.
Deal with any other faults.
Clear the stored faults.
DF096
PRESENT OR
STOREDTHROTTLE POSITION POTENTIOMETER CIRCUIT GANG 21.DEF: Signal incoherent
WARNING
Never drive the vehicle without having confirmed that no faults involving the throttle valve are present.
NOTESDeal with the following faults first:
DF011 Sensor supply voltage no. 1.
Special notes:
OBD warning light and level 1 fault warning light illuminate,
The throttle no longer operates
See the Wiring Diagrams Technical Note for Logan, Sandero, Duster, Thalia 2/
Symbol 2, Clio II F 6, Kangoo VLL.
Check the cleanliness of the throttle valve, component code 1076 and that the throttle rotates properly (no
resistance point).
Check the cleanliness and condition of the injection computer connector, component code 120 and of the throttle
valve connector, component code 1076.
If the connector or connectors are faulty and if there is a repair procedure (see Technical Note 6015A, Repairing
electrical wiring, Wiring: Precautions for repair), repair the connector(s), otherwise replace the wiring.
Check the insulation, continuity and the absence of interference resistance on the following connections:
–3MQ between components 120 and 1076,
–3MN between components 120 and 1076,
–3MO between components 120 and 1076.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the throttle valve has been replaced, reinitialise the programming by running command RZ031 Throttle stop
programming.
If the fault is still present, contact Techline.
V42_V04_DF096/V42_V05_DF096/V42_V06_DF096/V42_V14_DF096/V42_V16_DF096/V42_V18_DF096

17B-67V2 MR-376-X76-17B050$082.mif
PETROL INJECTION
Fault finding – Interpretation of faults17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 05, 06,
14, 16, 18
AFTER REPAIRFollow the instructions to confirm repair.
Deal with any other faults.
Clear the stored faults.
DF101
PRESENT OR
STOREDMULTIPLEX ELECTRONIC STABILITY PROGRAM LINK1.DEF: Invalid multiplex signals generated by computer
NOTESNone
Test the ABS computer (see38C, Anti-lock braking system).
V42_V04_DF101/V42_V05_DF0101/V42_V06_DF101/V42_V14_DF101/V42_V16_DF101/V42_V18_DF101

17B-68V2 MR-376-X76-17B050$082.mif
PETROL INJECTION
Fault finding – Interpretation of faults17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 05, 06,
14, 16, 18
AFTER REPAIRFollow the instructions to confirm repair.
Deal with any other faults.
Clear the stored faults.
DF102
PRESENT OR
STOREDALTERNATOR POWER SIGNAL AVAILABLE1.DEF: Below minimum threshold.
NOTESSpecial notes:
OBD warning light comes on.
See the Wiring Diagrams Technical Note for Logan, Sandero, Duster, Thalia 2/
Symbol 2, Clio II F 6, Kangoo VLL.
Check the cleanliness and condition of the alternator connector, component code 103 and of the injection
computer connector, component code 120.
If the connector or connectors are faulty and if there is a repair procedure (see Technical Note 6015A, Repairing
electrical wiring, Wiring: Precautions for repair), repair the connector(s), otherwise replace the wiring.
Check the insulation, continuity and the absence of interference resistance on the following connection.
–2K between components 103 and 120.
If the connection is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the fault is still present, contact the Techline.
V42_V04_DF102/V42_V05_DF102/V42_V06_DF102/V42_V14_DF102/V42_V16_DF102/V42_V18_DF102

17B-74
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
V2 MR-376-X76-17B050$082.mif
PETROL INJECTION
Fault finding – Interpretation of faults17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 05, 06,
14, 16, 18
DF319
PRESENT OR
STOREDCAMSHAFT SENSOR CIRCUIT1.DEF: Plausibility
2.DEF: No signal.
NOTESPriority when dealing with a number of faults:
Deal with the following faults first:
– DF047 Computer supply voltage
– DF015 Main relay control circuit
– DF120 Engine speed sensor signal
– DF195 Camshaft sensor / engine speed consistency
– DF457 Flywheel target
– DF080 Camshaft dephaser circuit
– DF363 Camshaft dephaser
Conditions for application to a stored fault:
– The fault is declared present after the ignition has been switched on.
See the Wiring Diagrams Technical Note for Duster.
Check the condition and connection of the camshaft sensor connectors, component code 1265.
If the connector or connectors are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Check the internal resistance of the camshaft sensor. It must be greater than 100 k.
Check for +12 V on the camshaft sensor, component code 1265 on the following connection:
•3FB of component 1265.
Check the continuity, insulation and the absence of interference resistance on the following connection:
•3FB between components 1265 and 1047.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
V42_V04_DF319/V42_V05_DF319/V42_V06_DF319/V42_V14_DF319/V42_V16_DF319/V42_V18_DF319

17B-75
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
V2 MR-376-X76-17B050$082.mif
PETROL INJECTION
Fault finding – Interpretation of faults17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 05, 06,
14, 16, 18
DF319
CONTINUED
Check the continuity, insulation and the absence of interference resistance on the following connections:
•3SX between components 1265 and 120,
•3SV between components 1265 and 120.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the fault is still present, contact the Techline.

17B-77
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
V2 MR-376-X76-17B050$082.mif
PETROL INJECTION
Fault finding – Interpretation of faults17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 05, 06,
14, 16, 18
DF342
CONTINUED
Part 3:
Check the connection and condition of the connector of the injection computer, component code 120 and the
instrument panel, component code 247.
If the connector or connectors are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Check the continuity, insulation, and the absence of interference resistance on the following connection:
For Logan, Sandero, Duster, Clio II F 6 and Kangoo VLL:
•137C between components 247 and 120.
For Thalia 2/Symbol 2:
•3FH between components 247 and 120.
– If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A,
Electrical wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
– If the fault is still present, contact the techline.

17B-79V2 MR-376-X76-17B050$082.mif
PETROL INJECTION
Fault finding – Interpretation of faults17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 05, 06,
14, 16, 18
AFTER REPAIRFollow the instructions to confirm repair.
Deal with any other faults.
Clear the stored faults.
DF361
PRESENT OR
STOREDIGNITION COIL 1 - 4 CIRCUITCC.0: Short circuit to earth
CC.1: Short circuit to + 12 V
CO: Open circuit
NOTESConditions for applying the fault finding procedure to a stored fault:
The fault is present after starting the engine and under the following conditions:
– engine running at idling speed
Special note:
For CC.1 and CO, the OBD warning light and level 1 fault warning light illuminate.
For CC.0, the OBD warning light and level 2 fault warning light illuminate.
See the Wiring Diagrams Technical Note for Logan, Sandero, Duster, Thalia 2/
Symbol 2, Clio II F 6, Kangoo VLL.
The D4D and K7M engines are equipped with a quadruple ignition coil module.
The K4M engine is equipped with 4 "pencil" type coils.
D4D and K7M engines
Check the cleanliness and condition of the injection computer connector, component code 120 and of the coil
connector, component code 778.
If the connector or connectors are faulty and if there is a repair procedure (see Technical Note 6015A, Repairing
electrical wiring, Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Check the insulation, continuity and the absence of interference resistance on the following connections:
–3CV or 3CZ (for Clio II F 6) between components 120 and 778,
–3CW or 3CV (for Clio II F 6) between components 120 and 778.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
With the ignition on, check the supply of the ignition coil, component code 778 using a test light on connection 3NA.
Check the insulation, continuity and the absence of interference resistance on the following connection:
–3NA between components 1047 or 1016 (for Clio II F 6) and 778.
If the connection is faulty and if there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the fault is still present, contact the Techline.
V42_V04_DF361/V42_V05_DF361/V42_V06_DF361/V42_V14_DF361/V42_V16_DF361/V42_V18_DF361

17B-80V2 MR-376-X76-17B050$082.mif
PETROL INJECTION
Fault finding – Interpretation of faults17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 05, 06,
14, 16, 18
AFTER REPAIRFollow the instructions to confirm repair.
Deal with any other faults.
Clear the stored faults.
DF361
CONTINUED
K4M engine
Check the cleanliness and condition of the pencil coil no.1 connector, component code 1077, of the pencil coil no.4
connector, component code 1080 and of the injection computer connector, component code 120.
If the connector or connectors are faulty and if there is a repair procedure (see Technical Note 6015A, Repairing
electrical wiring, Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Check the insulation, continuity and the absence of interference resistance on the following connections:
–3CZ or 3CE (for Kangoo VLL) between components 120 and 1077,
–3CV between components 1077 and 1080.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring. Otherwise replace the wiring.
With the ignition on, check the supply of the pencil ignition coils, component code 1077 and 1080 using a test light
on connection 3NA of the injection relay, component code 1047 (for Logan, Sandero, Duster), on connection 3NA
of the fuel pump relay, component code 236 (for Kangoo VLL) or on connection 3N of the fuel pump relay,
component code 236 (for Thalia 2/Symbol 2).
Check the insulation, continuity and the absence of interference resistance on the following connection:
–3NA between components 1080 and 1047 (for Logan, Sandero, Duster) or 236 for Kangoo VLL),
–3N between components 1080 and 236 (for Thalia 2/Symbol 2).
If the connection is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the fault is still present, contact the Techline.