door lock RENAULT MEGANE SCENIC 1995 Service User Guide

GLAZING
Front door window
Place the rear upper stop (8) in contact with the
lower window pad and tighten it.
Tighten the rear guide shoe bolt (2).
Tighten the window mounting bolts (3).
54
Place the front upper stop (8) in contact with the
lower window pad and tighten it.
Close and lock the hood.
Close the door.
Position the window at the dimensions:
D = 55 mm (window/weatherstrip)
E = 10 mm (window/frame)
Visually check that the window is aligned with the
hood seals.
12470R
12277-3R
12277-3R1
Tighten the rear slider bolt (4).
Open the door.
Push the rear slider gently towards the exterior of
the door.
Tighten the nut (4).
Open and close the window several times. Check
that the window is positioned correctly (aligned)
in relation to the hood seals.
Tightening torque of all mounting bolts 8 N.m.
54-4

TRIMS OF OPENINGS OTHER THAN SIDE DOORS
Exterior hood trim
Fold the hood in its housing.
Immobilise the hood cover in the case of the elec-
trohydraulic model.
73
PRE7301
RR R R
EE E E
MM M M
OO O O
VV V V
AA A A
LL L L
Before carrying out any work, protect the seats
and the rear wings.
Open the hood, raise the front section beyond the
pushing point (neutral position).
Remove the front frame cover clamps.Unscrew the pin (1) and remove the locking han-
dle.
Unclip and remove the cover.
12431S
12432R
73-1

TRIMS OF OPENINGS OTHER THAN SIDE DOORS
Exterior hood trim
73
RR R R
EE E E
MM M M
OO O O
VV V V
AA A A
LL L L
Place the rear frame in a vertical position.
Seat the rear formed section (12) in the rear
frame.
Rivet (Ø 4×12) the side tensioning strap (10) to
the main control rod.
Pass the side tensioning cable (9) into the exterior
trim, rivet it (Ø 3×8) to the front crossmember.
Seat:
- the side formed section (8) on the front cross-
member,
- the front formed section (6) on the front
frame.
Fold the hood.
Clip the front formed section tightening wrench
(5).
Place the hood in the neutral position.
Secure:
- the side tensioning strap (7) to the main
frame,
- the main frame seal (4).
Place the rear frame in a vertical position.
Seat:
- the rear seal (12) on the rear frame,
- the front crossmember side seal (2).
Clip and clamp the front frame cover, secure the
handle, close the hood.
Adjustment of the windscreen aperture seal -
front crossmember side seal.
A clearance of 1 mm must be obtained between
the two seals by sliding the side seal.
In the event of sideways offset, slide the winds-
creen aperture seal as necessary after unseating it
at the front locks.
73-4

TRIMS OF OPENINGS OTHER THAN SIDE DOORS
Interior hood trim
73
RR R R
EE E E
FF F F
II I I
TT T T
TT T T
II I I
NN N N
GG G G
Engage the formed section (8) in the main roof
arch groove.
Rivet (Ø 3×10) the tensioning strap (2) and the in-
terior trim to the main roof arch.
Clip the formed sections (7) to the main roof arch
and the auxiliary roof arch.
Fit the interior trim tensioning cable (3).
Rivet (Ø 3×10) the tensioning strap (1) and the in-
terior trim to the rear frame.
Fold the hood, seat the front formed section (6),
align the trim.
Fit the handles (4) without tightening the bolts.
Rivet the interior trim (5) to the front crossmem-
ber.
Close and lock the hood.
Tighten the handle mounting bolts.
73-9

51
SIDE OPENING ELEMENT MECHANISMS
Rear door locking knob (C)

51
SIDE OPENING ELEMENT MECHANISMS
Front door lock (F)

51
SIDE OPENING ELEMENT MECHANISMS
Front door lock (F)

51
SIDE OPENING ELEMENT MECHANISMS
Rear door lock (G)

51
SIDE OPENING ELEMENT MECHANISMS
Rear door lock (G)

NON-SIDE OPENING ELEMENT
MECHANISMS
Tailgate lock barrel
Rear screen wiper motorPage
Contents
WINDOWS
Rear door sliding window
Rear screen
Rear quarter panel window
EXTERIOR PROTECTION
Rear bumper
55
54
Mechanisms and
accessories
54-1
54-3
54-6
55-1
52
52-1
52-3
Number plate lights mounting 56-1 EXTERIOR ACCESSORIES
56
59-1
59-3 Front seat belts
Rear seat belts
59INTERIOR SAFETY ACCESSORIES