air condition RENAULT SCENIC 2000 J64 / 1.G Technical Note 3426A Owner's Manual

Downloaded from www.Manualslib.com manuals search engine AIR CONDITIONING
Compressor
62
62-2
SCENIC Compressor
REMOVAL
Drain the R134a refrigerant circuit (refer to the
procedure described in the "Air conditioning" manual).
Disconnect the battery.
Remove:
– the cooling assembly (see section 19 ),
– the alternator (see section 16),
– the R134a refrigerant pipes retaining bolt,
– the four compressor mounting bolts.REFITTING
Refitting is the reverse of removal.
Tighten the R134a refrigerant pipes retaining bolt on
the compressor to 3 daN.m.
Fill the R134a refrigerant circuit using the filling
equipment.
IMPORTANT:
When replacing the existing compressor with a new
compressor, it is essential to drain some of the oil from
the new compressor, so that the amount of oil in the
new compressor corresponds to the amount of oil
drained from the oil compressor.
99211S
Oil drained
new
compressor=Oil
in the new
compressor-Oil remaining
in the old
compressor

Downloaded from www.Manualslib.com manuals search engine AIR CONDITIONING
Dehydration canister
62
62-3
SCENIC Dehydration canister
REMOVAL
Drain the R134a refrigerant circuit using the filling
equipment (refer to the procedure described in the
"Air Conditioning" manual).
Remove:
– the right hand mudguard,
– the mounting bolts which secure the pipes to the
dehydration canister,
– the two mounting bolts of the dehydration
canister (B).
Fit plugs to every hole to prevent any penetration by
moisture into the components.
REFITTING
Refitting is the reverse of removal.
Oil the threads with P.A.G. SP 10 oil and check that
the seals are in good condition.
Create a vacuum then fill the R134a refrigerant circuit
using the filling equipment (refer to the procedure
described in the "Air conditioning" manual).
When changing the dehydration canister, add 15 ml of
P.A.G. SP 10 oil to the compressor.
16763R

Downloaded from www.Manualslib.com manuals search engine AIR CONDITIONING
Condenser
62
62-4
SCENIC Condenser
REMOVAL
Place the vehicle on a lift.
Drain the R134a refrigerant circuit (refer to the
procedure described in the "Air conditioning"
manual).
Remove:
– the six mounting bolts of the upper cross member,
– the two lower mounting bolts of the condenser on the
fan unit, then the two upper bolts,
– the mounting bolts of the pipes on the condenser.
Fit plugs to prevent any moisture penetration.
Remove the condenser.
98838S

Downloaded from www.Manualslib.com manuals search engine AIR CONDITIONING
Pressure relief valve
62
62-5
SCENIC Pressure relief valve
REPLACEMENT
Drain the R134a refrigerant circuit using the filling
equipment (refer to the procedure described in the "Air
Conditioning" manual).
Remove the right hand cowl vent grille.
Slacken the left hand cowl vent grille.
Remove:
– the scuttle,
– the retaining bolt of the connection pipe, using a
5 mm Allen key
– the two retaining bolts of the pressure relief valve on
the evaporator using a 4 mm Allen key.
On refitting, ensure that the pipe seals are in good
condition.
Create a vacuum then fill the R134a refrigerant circuit
using the filling equipment (refer to the procedure
described in the "Air conditioning" manual). TIGHTENING TORQUES (in daN.m)
Pressure relief valve retaining bolt 0.6
Pipe retaining bolt 0.8
16766S

Downloaded from www.Manualslib.com manuals search engine AIR CONDITIONING
Connecting pipes
62
62-6
SCENIC Connecting pipes
Disconnect the battery.
Drain the R134a refrigerant circuit using the filling equipment (refer to the procedure described in the "Air
Conditioning" manual).
LOW PRESSURE PIPE
REMOVAL
Remove the right hand cowl vent grille.
Slacken the left hand cowl vent grille.
Remove:
– the scuttle,
– the mounting bolt on the pressure relief valve,
– the mounting bolt on the compressor.
Fit plugs to prevent any moisture penetration.
Remove the low pressure hose.
The low pressure circuit can be partially dismantled by
unclipping the click-fit connector (1).
REFITTING
Refitting is the reverse of removal.
Check the condition of the seals and lubricate with
PLANETELF PAG 488 (approximately 2 g).
When changing a pipe, add 10 ml of PLANETELF
PAG 488 oil or when a pipe bursts (rapid leak), add
100 ml.HIGH PRESSURE PIPE BETWEEN THE
COMPRESSOR AND THE CONDENSER
REMOVAL
Remove:
– the mounting bolt on the compressor,
– the mounting bolt on the condenser.
Disconnect the tri-function pressure switch.
Remove the high pressure hose.
Fit plugs to prevent any moisture penetration.
REFITTING
Refitting is the reverse of removal.
Check the condition of the seals and lubricate with
PLANETELF PAG 488 (approximately 2 g).
When changing a pipe, add 10 ml of PLANETELF
PAG 488 oil or when a pipe bursts (rapid leak), add
100 ml.
PRF6203
PRF6204

Downloaded from www.Manualslib.com manuals search engine AIR CONDITIONING
Connecting pipes
62
62-7
SCENIC
Disconnect the battery.
Drain the R134a refrigerant circuit using the filling equipment (refer to the procedure described in the "Air
Conditioning" manual).
HIGH PRESSURE PIPE BETWEEN THE
DEHYDRATION CANISTER AND THE PRESSURE
REDUCING VALVE
REMOVAL
Remove the right hand cowl vent grille.
Slacken the left hand cowl vent grille.
Remove the scuttle,
Detach the pipe from its mountings.
Remove the high pressure hose.
Fit plugs to prevent any moisture penetration.
REFITTING
Refitting is the reverse of removal.
Check the condition of the seals and lubricate with
PLANETELF PAG 488 (approximately 2 g).
When changing a pipe, add 10 ml of PLANETELF
PAG 488 oil or when a pipe bursts (rapid leak), add
100 ml.HIGH PRESSURE PIPE BETWEEN THE
DEHYDRATION CANISTER AND THE CONDENSER
REMOVAL
Remove:
– the mounting bolt on the dehydration canister,
– the mounting bolt on the condenser.
Fit plugs to prevent any moisture penetration.
Remove the high pressure hose.
REFITTING
Refitting is the reverse of removal.
Check the condition of the seals and lubricate with
PLANETELF PAG 488 (approximately 2 g).
When changing a pipe, add 10 ml of PLANETELF
PAG 488 oil or when a pipe bursts (rapid leak), add
100 ml.
PRF6205
PRF6206